Uploaded October 2024 | Updated November 2026, 2 days ago
This video works as a guide for how to swap out the tach/hour meter cable on your L2502 model Kubota Tractor.
What you'll need:
10 mm socket (for instrument cluster)
12 mm socket ( for removing the cowling over the instrument panel)
Scissors/Cutters for cutting the zip ties.
17mm socket (to remote the steering wheel nut)
The process should be as follows:
Open the hood.
Remove both engine guards on both sides (the grey plastic pieces) Left side is a wing nut. Right site is a 12mm socket.
NOTE: All the 10mm and 12mm bolts are identical, so you don't have to remember which one goes where with one exception. I didn't know that at first so I kept track of them. The top 12mm bolt over the instrument cluster is black (to blend in with your black cover). The bottom one and the two on the sides are silver in color.
Instrument Cluster Stuck?
I couldn't record this because I didn't have enough hands, but when you pull the cowling up to reveal the instrument cluster, there are two connections you can pull off. You don't "need" to but I found it helpful. Both are pop-style connectors so you can spring them apart with just your hands.
After you remove what feels like everything you'll still notice that your instrument cluster really doesn't want to move. I learned it's the tach cable itself wedging it into place. On the right side of the cluster there is a black bar attached with 12mm bolts above and below the cluster. THIS is the black bar that the tach cable is wedged behind. Take your 12mm socket and loosen both bolts a bit and the cluster will move easier. Then you can pull it out, remove the old cable, put the new cable in, reseat the cluster, put the four 10mm bolts back in, retighten the 12mm bolts you just loosened, and go ahead and fire up the tractor to be sure you got it installed right.
If you see the tach move, you're back in business.
Reassembly should be fairly straight-forward. No spare parts left when you're done ok?
Entire time to complete this repair took me about 40 minutes, in a dirt lot, with limited tool. It would probably take me 30 in the shop with a concrete floor to work on, or 20 if I had another set of hands to help out.
I hope you find this useful.
Special thanks to Stanly Tractor Company in New London NC who had 1 spare tach cable on hand for $37.00!
© Copyright 2024, by Tommy Jordan. All rights reserved. Duplication without express written permission of the author is prohibited.
This video works as a guide for how to swap out the tach/hour meter cable on your L2502 model Kubota Tractor.
What you'll need:
10 mm socket (for instrument cluster)
12 mm socket ( for removing the cowling over the instrument panel)
Scissors/Cutters for cutting the zip ties.
17mm socket (to remote the steering wheel nut)
The process should be as follows:
Open the hood.
Remove both engine guards on both sides (the grey plastic pieces) Left side is a wing nut. Right site is a 12mm socket.
NOTE: All the 10mm and 12mm bolts are identical, so you don't have to remember which one goes where with one exception. I didn't know that at first so I kept track of them. The top 12mm bolt over the instrument cluster is black (to blend in with your black cover). The bottom one and the two on the sides are silver in color.
Instrument Cluster Stuck?
I couldn't record this because I didn't have enough hands, but when you pull the cowling up to reveal the instrument cluster, there are two connections you can pull off. You don't "need" to but I found it helpful. Both are pop-style connectors so you can spring them apart with just your hands.
After you remove what feels like everything you'll still notice that your instrument cluster really doesn't want to move. I learned it's the tach cable itself wedging it into place. On the right side of the cluster there is a black bar attached with 12mm bolts above and below the cluster. THIS is the black bar that the tach cable is wedged behind. Take your 12mm socket and loosen both bolts a bit and the cluster will move easier. Then you can pull it out, remove the old cable, put the new cable in, reseat the cluster, put the four 10mm bolts back in, retighten the 12mm bolts you just loosened, and go ahead and fire up the tractor to be sure you got it installed right.
If you see the tach move, you're back in business.
Reassembly should be fairly straight-forward. No spare parts left when you're done ok?
Entire time to complete this repair took me about 40 minutes, in a dirt lot, with limited tool. It would probably take me 30 in the shop with a concrete floor to work on, or 20 if I had another set of hands to help out.
I hope you find this useful.
Special thanks to Stanly Tractor Company in New London NC who had 1 spare tach cable on hand for $37.00!
© Copyright 2024, by Tommy Jordan. All rights reserved. Duplication without express written permission of the author is prohibited.










