Uploaded October 2026 | Updated November 2026, 2 days ago
Another before and after, this time from my latest reduction firing.
To answer some questions from last time that popped up, the colourful spiky things you see that turn molten and white are called pyrometric cones, I’ve got a bucket stuffed with them, which I’ve collected over the years. They’re tools, measuring devices that are single use and quantify heatwork, which is heat over time. By seeing how bent over they are I can make a judgement on whether the firing has come to a conclusion or not. I aim for all three to be bent over and I don’t use a guard cone, (this is poor advice perhaps). A guard cone is essentially a cone that would show only melt and bend IF you over fired the kiln, meaning the temperature rose too much.
With this kiln and how reliable it is, I could probably fire it with a single cone, as I keep an eye on it the entire time and I practically watch the cones through spy-holes in the door as they flop. Whereas if you’re firing with an electric kiln and you aren’t there when it’s firing, a guard cone can be useful as it’ll tell you if something went wrong and the kiln did in fact over-fire.
Otherwise, yes, pots shrink. From when freshly thrown to finally glaze fired, this specific body constricts about 12.5%, porcelains can be even more dramatic, shrinking up to 16%, that’s understated though, as volumetrically that’s a 40% reduction. This means the work you make initially has to be slightly oversized.
It’s one of those things you get used to gradually, although it’s always a shock with the larger pots I make as the shrinkage is more severe, with my larger urns and storage jars always feel far tinier as compared to the forms I threw at the start.
FINALLY, yes! On the lowest layer there are some pots that have already been fired. These normally have a defect of some kind and by firing them again, I’m attempting to resolve those. It could be a touch of crawling, (this is when glaze separates from itself), so I patch up and fire them again. Or, they might have under-fired initially, and a second go through the kiln is normally enough to fix that.
#pottery #beforeandafter #ceramics #craft #satisfying
Another before and after, this time from my latest reduction firing.
To answer some questions from last time that popped up, the colourful spiky things you see that turn molten and white are called pyrometric cones, I’ve got a bucket stuffed with them, which I’ve collected over the years. They’re tools, measuring devices that are single use and quantify heatwork, which is heat over time. By seeing how bent over they are I can make a judgement on whether the firing has come to a conclusion or not. I aim for all three to be bent over and I don’t use a guard cone, (this is poor advice perhaps). A guard cone is essentially a cone that would show only melt and bend IF you over fired the kiln, meaning the temperature rose too much.
With this kiln and how reliable it is, I could probably fire it with a single cone, as I keep an eye on it the entire time and I practically watch the cones through spy-holes in the door as they flop. Whereas if you’re firing with an electric kiln and you aren’t there when it’s firing, a guard cone can be useful as it’ll tell you if something went wrong and the kiln did in fact over-fire.
Otherwise, yes, pots shrink. From when freshly thrown to finally glaze fired, this specific body constricts about 12.5%, porcelains can be even more dramatic, shrinking up to 16%, that’s understated though, as volumetrically that’s a 40% reduction. This means the work you make initially has to be slightly oversized.
It’s one of those things you get used to gradually, although it’s always a shock with the larger pots I make as the shrinkage is more severe, with my larger urns and storage jars always feel far tinier as compared to the forms I threw at the start.
FINALLY, yes! On the lowest layer there are some pots that have already been fired. These normally have a defect of some kind and by firing them again, I’m attempting to resolve those. It could be a touch of crawling, (this is when glaze separates from itself), so I patch up and fire them again. Or, they might have under-fired initially, and a second go through the kiln is normally enough to fix that.
#pottery #beforeandafter #ceramics #craft #satisfying










