Making of Lithium - ion Battery 🔋🔋For Electric Vehicle (EV) and Solar Project || DIY ||Green Earth🌍🌎 @electriccreator

electric creator #howtomake #lithiumionbattery #DIY #EV #Electricvehicle #Battery #NMC #electriccycle #cyclebattery #BMS #lithium #ion #powerpack #greenenergy #creativescience #makingbattery

Making a battery of Electric Cycle my requirement is 48v & 10Ah battery which i have made from li-ion 26650 cells (Per cell is 3.7v & 5000mah) i have used 26 cells for making this kind of power pack. This i have made of my electric cycle project battery is giving very good efficiency 90-95% this cells are of 5c so we can get good range on EV-electric vehicle. This power pack discharge current is 50A.

making video of electric cycle link is :- youtu.be/Or3pyeVMv1I

Contact details for lithium ion battery Manufacturer:-

Meshi lithium battery
Address:-42 siddhivinayak industrial estate laskana to kholvad road, Surat, Gujarat.
Mob:-8469646654

Material requirement :-
1). 26650 cells (Per cell is 3.7v & 5000mah). 26pcs
2). Some Nickel Strip.
3). BMS(Battery Management System) 13S 20A.
4). 26650 cell holder.
5). heat sink tube.
6). some meter copper wire.

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

updated 3 years ago

Making of Lithium - ion Battery 🔋🔋For Electric Vehicle (EV) and Solar Project || DIY ||Green Earth🌍🌎

electric creator 2021-10-03 | #howtomake #lithiumionbattery #DIY #EV #Electricvehicle #Battery #NMC #electriccycle #cyclebattery #BMS #lithium #ion #powerpack #greenenergy #creativescience #makingbattery

Making a battery of Electric Cycle my requirement is 48v & 10Ah battery which i have made from li-ion 26650 cells (Per cell is 3.7v & 5000mah) i have used 26 cells for making this kind of power pack. This i have made of my electric cycle project battery is giving very good efficiency 90-95% this cells are of 5c so we can get good range on EV-electric vehicle. This power pack discharge current is 50A.

making video of electric cycle link is :- youtu.be/Or3pyeVMv1I

Contact details for lithium ion battery Manufacturer:-

Meshi lithium battery
Address:-42 siddhivinayak industrial estate laskana to kholvad road, Surat, Gujarat.
Mob:-8469646654

Material requirement :-
1). 26650 cells (Per cell is 3.7v & 5000mah). 26pcs
2). Some Nickel Strip.
3). BMS(Battery Management System) 13S 20A.
4). 26650 cell holder.
5). heat sink tube.
6). some meter copper wire.

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Smart Robot Dustbin

electric creator 2024-07-22 | ...

3axis Robot 🤖🤖

electric creator 2023-07-31 | ...

How to make Smart Dustbin || DIY Project

electric creator 2023-02-09 | This project is very helpful for city development and college projects.

code link :-

circuit diagram :-

Join this channel to get access to perks:
youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ/join

For more video :-youtube.com/c/electriccreator

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Indias 🇮🇳🇮🇳 First Made in India electric cycle IOT Based Smart Bicycle - BLDC motor controller

electric creator 2022-07-06 | This final year project solving the problem of Overspeed issue, Trouble in BLDC Controlling, It require more charging time, Battery lifespan, Vehicle Tracking, High cost of charger, EV driving range, Battery cost.

OBJECTIVE OF PROJECT
Enabling IOT to avoid danger of overspeed.
Taking Proper Feedback From Hall sensor.
Reducing total charging time to 60 - 75%.
Keeping the low Amps of charger to maintain constant battery life cycle.
Integrating GPS module as a tracker.
Increasing the driving range

Media coverage News link :- patrika.com/surat-news/e-vehicle-surat-students-invented-unique-e-cycle-7524544

Join this channel to get access to perks:
youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ/join

For more video :-youtube.com/c/electriccreator

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Smart plant monitoring system with OLED display🪴🪴🪴🌱🌱🌱

electric creator 2022-03-26 | This project is very helpful for the farmers and nursery.

code link :-drive.google.com/file/d/17JObml5X5vo5ZixAByxbS1xzYRZJtJJb/view

circuit diagram :-
drive.google.com/file/d/17IHAqBqT9SnFFI4H0rA6-AHyyR5eGzSZ/view

Join this channel to get access to perks:
youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ/join

For more video :-youtube.com/c/electriccreator

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Indias First Smart Delivery Robot 🇮🇳🇮🇳🤖🤖

electric creator 2022-02-06 | #robot #diy #diyproject #howtomake #homemade #smartrobot #madeinindia #fristtime #robotics #automation

Fully Smart Delivery robot iot and AI based robot,it is used to have other people's to make a life convenient from this robot we have made so many features like camera, obstacle avoidance,manual controls or human detection systems and etc.

The future is here! Their robots ready to serve you. robots are advanced devices that can carry items within a 4-mile (6km) radius and travel about 4 miles per hour.

Code and Cricuit Diagram :- drive.google.com/drive/folders/17EUTIog3o2DUtEaBH36QkQJweuPqO_tK?usp=sharing

How to make a powerful 15.2V 15600mAh li-ion Battery Pack for Robot :-youtu.be/Zoge50MtPd0

Join this channel to get access to perks:
youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ/join

For more video :-youtube.com/c/electriccreator

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Indias First Delivery Robot

electric creator 2022-02-03 | Join this channel to get access to perks:
youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ/join

Which Microcontroller is best for beginners ⁉️

electric creator 2022-01-26 | In this tutorial we will learn about the which Microcontroller is best for beginners in robotics, automation, power electronics, embedded systems. this all Microcontroller are Basic one you go for advance controller also like STM32 and etc.

if you have not seen my previous videos please go and See my previous video playlist the link is here:- youtube.com/playlist?list=PLKUKq8h48EzFZWQ5KHlKr4M82vDfK7rAs

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

autonomous robot #robot #diy #diyproject #howtomake #homemade #smartrobot #madeinindia #shortvideo

electric creator 2022-01-04 | ...

Real Time GPS Location Tracker | Nodemcu ESP8266

electric creator 2022-01-01 | #GPStracker #DIY #gpstracker #homemade #vehicletracking #tractor #blynk #iot #diyproject

Hey friends in this video I will show you how to make Real time GPS Location Tracker using nodemcu esp8266. You can also install into you Bike, Cycle & Car.

Download Codes and Circuit Diagrams :- drive.google.com/drive/folders/1CcauJ4M3t_WbHF8hBat-N_apTuUJlCUH?usp=sharing

Materials:-
1). Nodemcu ESP8266
2). NEO 6M GPS Module
3). Jumpers
4). Smart Phone

Join this channel to get access to perks:
youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ/join

For more DIY Project visit over channel electric creator :-
youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Banana Car #BananaCar #electricvehicle #ev #gogreen #diy @CreativeScienceOfficial

electric creator 2021-12-30 | ...

smart door security system #smartdoorlock #diy #homemade #arduino #howtomake #FingerprintLock #short

electric creator 2021-12-25 | #shortvideo #shorts #diyproject

Home automation using NodeMCU (ESP8266) and Blynk App - IOT based Project #automation

electric creator 2021-12-19 | #automation #iot #diyproject #homemade #homeautomation #esp8266 #nodemcu #howtomake #arduino #blynk

In this IoT based project, we will learn how to do Home automation using NodeMCU and Blynk App. This is a simple but useful home automation project with Nodemcu and a relay module where we can control home appliances securely from the smartphone.

During the video, I have shared the circuit diagram, Arduino sketch, Blynk example library for this internet of things project.

I have also shown the components used, it's circuit diagram and almost everything that require to make this amazing project.

Code and Circuit diagram link :-drive.google.com/drive/folders/1EnTkxEyfjqD6ohe9IojQHHiWCkLVhWXC?usp=sharing

if you have not seen my previous videos please go and See my previous video playlist the link is here:- youtube.com/playlist?list=PLKUKq8h48EzFZWQ5KHlKr4M82vDfK7rAs

Material used:-
1).Nodemcu - esp8266
2).Same jumper wires
3). copper wire 1mm
4). Four Channel relay module
5). Any load like Bulb, fan and etc

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Electric cycle #electricvehicle #electriccycle #diy #diyproject #cycle #lithiumionbattery #homemade

electric creator 2021-12-16 | #short #shortvideo #shorts #lithiumionbattery #electricvehicle #diyproject #diy #howtomake

OLED Displays with Arduino Nano - I2C OLEDs @CreativeScienceOfficial

electric creator 2021-12-11 | OLED (Organic Light Emitting Diode) displays have a lot of advantages over LCD and traditional LED displays. Today we will learn how to use OLED displays with our Arduino projects. We’ll also build a Image to CPP conversion on display.

OLED displays a bright, lightweight, and easy to read in almost any lighting condition. They come in all sizes, from huge wall-sized OLED televisions to thumbnail-sized status displays.

Today we will work with three small OLED displays:

- A 128x32 monochrome display that uses I2C
- A 128x64 dual-color display that also uses I2C
- A Waveshare 1.5 inch 128x128 monochrome display that can use either I2C or SPI

Code and circuit diagram :- drive.google.com/drive/folders/1G2-Crna6fy8_8nxbM57g8xy42uEa2SXP?usp=sharing

For more DIY Project visit over channel electric creator :-
youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

lithium ion battery pack assembly #lithiumion #lithiumionbattery #diy #homemade @electric creator

electric creator 2021-12-08 | #howtomake #lithiumionbattery #DIY #EV #Electricvehicle #Battery #NMC #electriccycle #cyclebattery #BMS #lithium #ion #powerpack #greenenergy #creativescience #makingbattery

Making a battery of Electric Cycle my requirement is 48v & 10Ah battery which i have made from li-ion 26650 cells (Per cell is 3.7v & 5000mah) i have used 26 cells for making this kind of power pack. This i have made of my electric cycle project battery is giving very good efficiency 90-95% this cells are of 5c so we can get good range on EV-electric vehicle. This power pack discharge current is 50A.

Full making Video this Lithium ion Battery 48v 10Ah Link:-youtu.be/QSKNPYlpxzs

Contact details for lithium ion battery Manufacturer:-

Meshi lithium battery
Address:-42 siddhivinayak industrial estate laskana to kholvad road, Surat, Gujarat.
Mob:-8469646654 / 8000346746

Material requirement :-
1). 26650 cells (Per cell is 3.7v & 5000mah). 26pcs
2). Some Nickel Strip.
3). BMS(Battery Management System) 13S 20A.
4). 26650 cell holder.
5). heat sink tube.
6). some meter copper wire.

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Arduino RFID Card Door lock System || Multiple Cards (MFRC522) || DIY

electric creator 2021-12-04 | In this video, We have Made the best smart RFID door lock. This is the safest lock to use for the home or office. This smart RFID lock has many smart features which is have added that have surprised me also. I have talked about all of them so please watch the video till the end.

Code and circuit diagram :- drive.google.com/drive/folders/1ellg1r3rd96cTQZ0vJa_l9Owz3ZCSiKY?usp=sharing

Required Materials :-

1). Arduino Nano.
2). RFID reader MC522 Module.
3). LM7803 IC.
4). 7805 IC.
5). Push Button.
6).12v 2A Power Adapter .
7). 100uf and 10uf Capacitor.
8). Zero Board.
9). Male and Female Bug.
10). 12V Relay.
11). i2c 16x2 Display.
12). Jumper Wire.

For more DIY Project visit over channel electric creator :-
youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Racing boat ⛵ #RCboats #diy #diyproject #homemade #boat #boatrace #howtomake #rc 😀😀😀⛵⛵⛵

electric creator 2021-12-02 | #Boat #electricboat #evboat #ev #automation #iot #racingboat #diy #homemade #robot #diyproject #arduino #shorts #short #shortvideo

In this project tutorial we will learn how to Make RC Boat at Home using BLDC Drone Motor by using android device via WiFi over the Internet. We will use the NodeMCU (ESP8266) for this tutorial.

To watch this full video link is here :-youtu.be/5kULKYFrYX8

How to do Wiring of Self-balancing one wheel electric Scooter at Home || DIY @CreativeScienceOfficial

electric creator 2021-11-27 | #howtomake #DIY #Onewheelscooter

In this video we are going to learn the wiring of self-balancing controller or one wheel scooter.

buying Link of self balancing controller :- gogoa1.com/products/60v-250w-350w-solo-wheel-controller

For more DIY Project visit electric creator :-
youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ

Video:-
1.How to make Self-balancing one wheel electric Scooter at home Part-1|| DIY
-youtu.be/KzkIBLLRTJA

2.How to make Self-balancing one wheel electric bike at home
-youtu.be/cqXd6oJAHSg

3.How to make Self-balancing one wheel electric Scooter at home Part-2|| DIY
-youtu.be/4IqlXYEYcFk

And I will also thankful to you creative science channel team who has helped me out to shoot this video and for everything.

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

electric tractor #tractor #electrictractor #minielectrictractor #electricvehicle @CreativeScienceOfficial

electric creator 2021-11-26 | #creativeScience #DIY

Type of lithium-ion Cell & its uses || Which Lithium cell is Best for Electric Vehicle ?? 🔋🔋🔋

electric creator 2021-11-20 | #howtomake #lithiumionbattery #DIY #EV #Electricvehicle #Battery #NMC #electriccycle #cyclebattery #BMS #lithium #ion #powerpack #greenenergy #creativescience #makingbattery #creativescience #trending #trendingtopic

In this Video we are going learn about the lithium cell which type of cell and which cell is best in electric vehicle.

Contact details for lithium ion battery Manufacturer:-

Meshi lithium battery
Address:-42 siddhivinayak industrial estate laskana to kholvad road, Surat, Gujarat.
Mob:-8469646654

For more DIY Project visit electric creator :-
youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ

And I will also thankful to you creative science channel team who has helped me out to shoot this video and for everything.

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

How to Make Fire or Smoke 🔥🔥🔥 Protection system || Homemade || DIY

electric creator 2021-11-14 | I have used DHT11 or MQ2 sensor for measuring an air quality of my room and mq2 to data will be sent to the e-mail if there will be gas, LPG or smoke leakage in your room. if the sensor detects smoke or gas then it will give you buzzer sound and email notification.

I have also shown the components used, it's circuit diagram and almost everything that require to make this amazing project.

if you have not seen my previous videos please go and See my previous video the link is here:- youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ

Material Required used:-
1).Nodemcu
2).DHT11 or DHT22
3).Same jumper wires
4). Adaptor 12V-2A
5).MQ2 or MQ135
6).Buzzer 5v
7).buck convertor

code & Circuit Diagram link :- drive.google.com/drive/folders/1Eu9GNu6YtpNKPHDSKIWzptGKNoUsh9n7?usp=sharing

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

How to Make Fingerprint Smart Door Security Lock 🔐🔐|| Nodemcu(ESP8266) || DIY

electric creator 2021-11-05 | #diy #diyproject #homemade #iot #fringerprinter(R-307) #howtomake #arduino #arduinoproject #nodemcu #esp8266 #collegeprojects #oled #smartdoor #smartdoorlock #electriclock
#dangerousLock

In this video, I have Made the best smart door lock for Office. This is the safest lock to use for the Office. This smart lock has many smart features which is i have added that have surprised me also. I have talked about all of them so please watch the video till the end.

Smart security system in this system I have integrated so many features fingerprint R-307 in anywhere in the world you can unlock the door. I can unlock my door through phone on sitting on my chair. I have also given a power backup in this smart door.

Code and circuit diagram :- drive.google.com/drive/folders/11c5ph4CxW0FTxbe-eaalaUh-yeNLo4HS?usp=sharing

Required Materials:-
1). R-307 Fingerprint Sensor.
2). Nodemcu Esp8266.
3). 12v relay.
4). 12v solenoid lock.
5). BC547 transistor.
6). Buzzer.
7). Led 2pcs.
8). OLED ssd1306 display.
9). zero board.
10). 7805 ic.
11). push button and toggle switch.

For more DIY Project visit electric creator :-
youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ

And I will also thankful to you creative science channel team who has helped me out to shoot this video and for everything.

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

How to Program or Setup the KK 2.1.5 Flight Controller || Drone Part - 2

electric creator 2021-10-28 | #drone #diy #homemade #howtomake #quadcopter #diyproject #flyrobu #flysky #electriccreator #india #CheapestDrone #RcDrone #kk2.1.5 #flightcontroller

Hello guys I hope all you are doing good in this video we are going to assemble a Drone which I have ordered from a flyrobu this is very interesting video please see this video till end this Drone can get height upto 150 feets and this can goes up to range of 500meter. this robot cost is very cheap you can make this Drone under 9999 rupees good quality drone.

Buying links :- https://www.flyrobo.in/quadcopter_combo_kit_for_beginner_motor_esc_propeller_flightcontroller

Part-1 Making Video Link :- youtu.be/W5_bo9SQTLA

For more video :-youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

How to Make cheapest Drone at home in Rs-8999 || Drone ||Homemade

electric creator 2021-10-23 | #drone #diy #homemade #howtomake #quadcopter #diyproject #flyrobu #flysky #electriccreator #india #CheapestDrone #RcDrone

Hello guys I hope all you are doing good in this video we are going to assemble a Drone which I have ordered from a flyrobu this is very interesting video please see this video till end this Drone can get height upto 150 feets and this can goes up to range of 500meter. this robot cost is very cheap you can make this Drone under 9999 rupees good quality drone.

Buying links :- https://www.flyrobo.in/quadcopter_combo_kit_for_beginner_motor_esc_propeller_flightcontroller

if you want full setup video of flight controller KK 2.1.5 please comment on description I will make that video.

For more video :-youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

How to make 3 Axis Arm using Nodemcu or Arduino Board || DIY

electric creator 2021-09-28 | #iot #robot #3axisarm #creativescience #electriccreator #3axis #nodemcu #servomotors #diy #diyproject #homemade #3dprinting

In this DIY project we will learn how to make 3-Axis Arm with wifi control by using android device via WiFi over the Internet. We will use the NodeMCU ESP8266-12E for this project and MG995 Servo Motor.

To download circuit diagram & code:
Link :-drive.google.com/drive/folders/1MVZnqu9EZBQQTXDxTaE8ZjedI_-Y8gLk?usp=sharing

Required Material :-
1. ESP8266 ESP-12 (NodeMcu) - 1pcs
2. Servo Motor MG99 3pcs
3.Jumper wire
4.Servo Motor MG90s 1pcs
5. Lithium-ion 18650 3pcs
6. Any Android Mobile.

I will thankful to the creative science team for supporting me.

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

How to make smart 2 in 1 Line follow with wifi control || DIY project

electric creator 2021-09-20 | #linefollow #2in1robot #iot #robot #smartrobot #mobilecontrol #line #AI #Nodemcu #IRsensor #DIYproject #DIY #Project #Wificontrol #internetcontrol #Arduino

In this DIY project we will learn how to make smart 2 in 1 Line follow with wifi control by using android device via WiFi over the Internet. We will use the NodeMCU ESP8266-12E for this project and L298N motor Driver Board also IR Sensor for line follow.

To download circuit diagram & code:
Link :- drive.google.com/drive/folders/18CDGMpAJk7fDyrk4m-p7PsPVjhedCRVr?usp=sharing

Required Material :-
1. ESP8266 ESP-12 (NodeMcu) - 1pcs
2. Dual H Bridge DC Motor Drive Controller Board Module - 1pcs
3. Geared DC Motor 200_rpm 12v - 2pcs
4. Frame for Holding 2 DC Motors. 1pcs
5.IR Sensor 2pcs
6. Lithium-ion 18650 3pcs
7. 3s Cell Holder 1pcs
7. Some Jumper wire Female to Female
8. Any Android Mobile.

I will thankful to the creative science team for supporting me.

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Homemade AC to DC Variable Power Supply || DIY || All in one

electric creator 2021-09-16 | #dcpowersupply #ACtoDC #charger #varaiablepowersupply #creativescience #dcpower #homemade #powersupply #allinone #iot
This video shows you how to make AC to DC power supply here you can connect different type of load across power supply this power supply can handle upto 0-25v and 0-10A .

Required Material :-
1. SMPS 24v 10A 1Pcs
2. Voltage ampere display 1Pcs
3. Red Black prob. 1Pcs
4. Some Jumper wire. 1pcs
5. Rocker switch. 1pcs
6. multiturn 10k potentiometer. 1pcs
7. 10k potentiometer. 1pcs
8. buck convertor 300w. 1pcs
9. 12v dc fan. 1pcs
10. fuse box. 1pcs
11. three pin connector. 1pcs

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

How to make Racing Boat ⛵ ⛵ at Home ||DIY 🛥️🛥️

electric creator 2021-09-05 | #Boat #electricboat #evboat #ev #automation #iot #racingboat #diy #homemade #robot #diyproject #arduino

In this project tutorial we will learn how to Make RC Boat at Home using BLDC Drone Motor by using android device via WiFi over the Internet. We will use the NodeMCU (ESP8266) for this tutorial.

Material:-
1). 3-inchs PVC pipes
2). BLDC Drone Motor
3) Battery 12v 10Ah or Li-po battery
4) Glue of PVC Pipe
5) Switch
6) And some wire

To download code:drive.google.com/file/d/1Wdi-w6taAW2nR1mQa8ig84j9drfnGH7V/view?usp=sharing

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

how to make Electric Bicycle🚴🚴 || Hub Motor || Lithium-ion Battery || Diy Project

electric creator 2021-07-30 | #electricbike #ev #electriccycle #cycle #smartcycle #diy #diyproject #homemade #electric #lithiumionbattery #ElectricCreatorCycle

In this video we have made an electric cycle hindi cycle i have used 48v 10ah battery and it give me range of 50 kilometres in 2.5 rupees. if you want to make this kind of battery I have given contact in below you can contact Meshi lithium batteries.

Contact details for lithium ion battery Manufacturer:-

Meshi lithium battery
Add:-42 siddhivinayak industrial estate laskana to kholvad road Surat Gujarat

Mob:-8469646654

For more Videos visit our channel Link:- youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.😀😀😀🙏🙏

Indias 🇮🇳🇮🇳 First RTO Approved Electric Conversion Kit for Bike 🚨🚨 || GoGoA1.com

electric creator 2021-07-07 | #GoGoA1 #Testing #ev #Splendorconversion #Splendor
#GogoA1splender #GoGoA1.com #creativescience #evconversion

this kit has been designed by the Gogo a1.com which is the manufacture of conversion kit this kit is is approved by the RTO and ARAI approved. this kind of Kit can be fitted in any kind of bike. But here gogoa1.com has only approved splendor bike for this kit. In this bike we can claim also insurance.

Buying link :- gogoa1.com/products/gogoa1-17inch-2000w-brushless-hub-motor-kit-for-motorcycle-electric-conversion

For more Videos visit our channel Link:- youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

😱😱Fat tyre Electric Bicycle 🚴🚴

electric creator 2021-06-30 | we have made this super fat tyre electric bicycle to watch complete video link is here :- youtu.be/qfORLtP-TME

😂😂🔥🔥 (WATCH TILL END) While Testing The Wheelchair See What Just Happened😭😱🤭

electric creator 2021-05-14 | while testing the wheelchair accident happened because of some technical fault

How to Setup 3D Printer for First time🛠️🖨️🛠️🖨️😊

electric creator 2021-05-10 | this video we will going learn about how to use 3D printer and how to setup with the PC and how to dump the program in the 3D printer to run and start the printing of the 3D three-dimensional object.

here we will also print and ganpati bappa murti to check the accuracy of the 3D printer here we are using Ender 3d printer.

So I decided to print some models to see what it could do.
In this video, you’ll see my very first print with this 3D printer.

Buying link of 3d printer : - https://www.amazon.in/dp/B07BR3F9N6/ref=cm_sw_r_wa_apa_glt_fabc_1CR2JGX99RAPGW64KVHB

I will thankful to the creative science team for supporting me and we are bringing very amazing and big project for you on YouTube channel please stay tuned with us.

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

How to Control Hub Motor ⚙️ (BLDC) from Mobile📲

electric creator 2021-04-01 | In this project tutorial we will learn how to control a hub motor by using android device via WiFi over the Internet. We will use the NodeMCU (ESP8266) for this tutorial, this tutorial is the part of the project or a big project.

this is the first time on YouTube controlling a hub motor with a iot module or smartphone

To download code:
Link :- drive.google.com/file/d/1UDKuQ4--Qs8NGOlHSY44D2784IODUt0S/view?usp=sharing

I will thankful to the creative science team for supporting me and we are bringing very amazing and big project for you on YouTube channel please stay tuned with us.

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Smart Door Security Lock For Home 🔐 || Dangerous Lock 😱 || ⚠️🚨 BE ALERT 🚨⚠️

electric creator 2021-02-15 | In this video, I have Made the best smart door lock for home. This is the safest lock to use for the home. This smart lock has many smart features which is i have added that have surprised me also. I have talked about all of them so please watch the video till the end.

Smart security system in this system I have integrated so many features like card unlock, face and eye detection unlock and in anywhere in the world you can unlock the door.if someone comes in front of camera system it will automatically send photo to system and it will send the notification to my phone and I can unlock my door through phone on sitting on my chair. I have also given a power backup in this smart door

This DIY project have a feature like :-
1). Notification in mobile phone with photo if someone come on door.
2). Anti - theft alarm system.
3). Take photo feature again and again.
4). Via a internet door unlock and we can take photo also.
5). It has RFID reader system .
6). We can unlock the door via smart card and smart Tag also.
7). It has a power back of 5-6 hour.
8). If someone come on the door it automatically start taking photo, give a Notification on mobile and Bell will automatically ring.
9). It has a two IR sensor to detect human or object.
10). It has AI(Artificial Intelligence) based camera it can unlock the door if when the saved or unroll person come in front of camera.
11). RFID Reader Lock + Internet based Camera Lock Integrated System.

For more DIY Project visit electric creator :-
youtube.com/channel/UCYJyLsf3RsRNXfl87PSg3oQ

I will like to thank you who has Sponsored this video Janmay Trivedi.

And I will also thankful to you creative science channel team who has helped me out to shoot this video and for everything.

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Arduino Nano with Voltage Sensor(0-25V) & Current Sensor(0-30A)

electric creator 2021-01-06 | This video shows you how to Arduino Voltage & Current Sensor. You will learn how to measure 25V DC and Ampere but trick is shown so you can measure virtually any voltage and Current.

To Download Code & Circuit diagram link is here :- drive.google.com/drive/folders/1YOnt0QpSV0ERHmOOlzfLkMLtJi1_WZqf?usp=sharing

Required Material :-
1. Arduino Nano 1Pcs
2. Voltage Sensor 1Pcs
3. Current Sensor(ACS712) 1Pcs
4. Some Jumper wire
5. Any Power Supply
6. Any load

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

How To Connect I2C LCD display(16x2) with Arduino Nano | I2C Display | Arduino Nano

electric creator 2020-12-27 | Interface LCD 16X2 with I2C module with Arduino Nano. Error fixing and 100% working Demonstration.
(Please let me know in the comments if the video has any issues on playing.)

To Download Codes link is here :-drive.google.com/file/d/1RtPz2PxV3i81hHg7iQ_mkh_B6EBiO4l_/view?usp=sharing

Connection Diagram :-

I2C module Arduino Nano

VCC --- 5V Pin
GND --- Ground Pin
SDA --- A4 Pin
SCL --- A5 Pin

Materials:-
1). Arduino Nano 1pcs
2). I2C Module 1Pcs
3). 16x2 Lcd display 1pcs
4). Jumper wire F to F 4Pcs
5). Nano cable 1Pcs

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

electric creator 2020-12-24 | In this project tutorial we will learn how to control robot car by using android device via WiFi over the Internet. We will use the NodeMCU ESP8266-12E for this project and L298N motor Driver Board.

To download circuit diagram & code:
Link :- drive.google.com/drive/folders/1kFG28H9firUgThMbqmaGI4MnVmd5inAe?usp=sharing

Required Material :-
1. ESP8266 ESP-12 (NodeMcu) - amzn.to/2SvpcCt
2. Dual H Bridge DC Motor Drive Controller Board Module - L298N D2 - amzn.to/2X9eX5M
3. 2 Geared DC Motor - amzn.to/2SvkmFn
4. Frame for Holding 2 DC Motors. - amzn.to/2E8nPkr
5. Any Android Mobile.

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Blynk ESP8266 DHT11 Temperature Sensor || WEATHER MONITORING System

electric creator 2020-12-20 | Hey friends in this tutorial i will show you how to get data of Temperature from NodeMcu ESP8266 board to your Smartphone through Blynk app

To Download Codes :-drive.google.com/file/d/1t-0r1aMz2G_sNSxk1HvIoKG7VPgb4XH0/view?usp=sharing

To Download Circuit Diagrams :- drive.google.com/file/d/1K91tJ71L_3-po38fmoaKHL_jSI668wqZ/view?usp=sharing

Materials:-
NodeMcu ESP8266 : https://www.flyrobo.in/nodemcu_esp826...
DHT11 Temperature Sensor : https://www.amazon.in/dp/B01MXRT9DZ/ref=cm_sw_em_r_mt_dp_vf03FbXWFGSFB
Jumpers : https://www.flyrobo.in/combo-of-3-typ...

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Autonomous robot 🤖

electric creator 2020-12-03 | Fully autonomous robot iot and AI based robot,it is used to have other people's to make a life convenient from this robot we have made so many features like line follower, obstacle avoidance,manual controls or human detection systems and etc.

To see full video link is here :- youtu.be/_CnTbfZWGuY

How to make a powerful 15.2V 15600mAh li-ion Battery Pack for Robot :-youtu.be/Zoge50MtPd0

Home Automation Playlist link:- youtube.com/playlist?list=PLKUKq8h48EzFZWQ5KHlKr4M82vDfK7rAs

Automatic Soap Dispenser Playlist link:- youtube.com/playlist?list=PLKUKq8h48EzFdNqD7bbvJGodstynCi5nD

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

How Robot is Working, Coding of Robot, Hardware Overview, Mobile or internet Controlling by Blynk.

electric creator 2020-11-18 | Fully autonomous robot iot and AI based robot,it is used to have other people's to make a life convenient from this robot we have made so many features like line follower, obstacle avoidance,manual controls or human detection systems and etc.

How to make a powerful 15.2V 15600mAh li-ion Battery Pack for Robot :-youtu.be/Zoge50MtPd0

Home Automation Playlist link:- youtube.com/playlist?list=PLKUKq8h48EzFZWQ5KHlKr4M82vDfK7rAs

Automatic Soap Dispenser Playlist link:- youtube.com/playlist?list=PLKUKq8h48EzFdNqD7bbvJGodstynCi5nD

Material for Robot Main Circuit Diagram :-
1). Zero board. 1Pcs
2).Nodemcu ESP8622. 1Pcs
3).Arduino Nano. 2Pcs
4).Soldering Wire.
5).BC547. 15Pcs
6).Relay 12V. 11Pcs
7).1k ohm Resistor. 20Pcs
8).220 ohm Resistor. 20pcs
9).7408 IC. 2Pcs
10).7486 IC. 1Pcs
11).7404 IC. 1Pcs
12).Buzzer 12V. 1Pcs
13).Line follower 8array sensor 1Pcs
14).IR sensor. 2Pcs
15).Male and Female Bug. 4Pcs each
16).7805 IC. 3Pcs
17).Heat sink. 3Pcs
18).Some LED Light 8pcs
19).Buck Converter 300w 1Pcs
20).Small fan 12v. 1Pcs
21).fan 12v. 1Pcs
22).Motor Driver VNH2SP30. 2Pcs
23).Battery 15.2V 15600mah power pack. 1Pcs
24)Diode IN4007. 25Pcs
24).Blynk server.

Creative Science Links:-
How to Make a Smart Robot Body at home Part-1 :- youtu.be/XNcdSkCjZWo
How to Make a Smart Robot Body at home Part-2 :-youtu.be/pE6wMa9kj_E

Autonomous Robot Code Link :-

Joystick Control(Nodemcu) :- drive.google.com/file/d/1_pK9ziG0QwmkNk97316s0_Fer4lxVev5/view?usp=sharing

Line follow 8 Array(Nano) :-drive.google.com/file/d/12N_75NKuadSdfn8zlWllomY1su1EJKY_/view?usp=sharing

Head code(Nano) :-drive.google.com/file/d/1XNWmW0aFeBO0qBXvRGdP6jC8nCJ6fyxl/view?usp=sharing

Circuit Diagram :- drive.google.com/file/d/1OURbyoMYJGMwzDvWlgyqpyoLFw6R2LEm/view?usp=drivesdk

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

How to make a powerful 15.2V 15600mAh li-ion Battery Pack for Electric Vehicle and Projects

electric creator 2020-11-13 | Making a battery of an robot my requirement is 15.2v & 15600mah battery which i have made is of li-ion 18650 cells (Per cell is 3.8v & 2600mah) i have used 24 cells for making this kind of power pack.

Material requirement :-
1). 18650 cells (Per cell is 3.8v & 2600mah) 24pcs
2). Some Nickel Strip.
3). BMS 4S 40A.
4). 18650 cell holder.

Contact details for lithium ion battery Manufacturer:-

Meshi lithium battery
Add:-42 siddhivinayak industrial estate laskana to kholvad road Surat Gujarat

Mob:-8469646654

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

circuit Assembly of Automatic soap and hand sanitizer dispenser

electric creator 2020-10-22 | If you touch normal dispenser it's very dangerous to spread the corona virus and other viruses so that we should go the automation please like and subscribe my channel technical secrets.if you want to see my previous video see on my channel and I will share the link. Be safe be happy.

Circuit Diagram:-drive.google.com/file/d/1R-NIpzeDYRSjrf5EKNzVgnglYI_W9QPq/view?usp=drivesdk

In circuit Assembly i have used material :-

1). BC547 transistor x1pcs
2). optocoupler(PC 817) x1pcs
3). 7404 IC(not gate) x1pcs
4). 12 volt adaptor x1pcs
5). IR sensor x1pcs
6). 1 Kohm Resistor x2pcs
7). IN-4007 Diode x1pcs
8). Zero board x1pcs
9). 7805 ic x1pcs
10). 100uf capacitor x1pcs
11). 10uf capacitor x1pcs
12). Motor or Pump x1pcs

Automatic soap and hand sanitizer dispenser 1.0 :- youtu.be/o5lJvouRU0g
Automatic soap and hand sanitizer dispenser 2.0 :- youtu.be/nSneP91Np9Q

If we touch the normal soap dispenser so virus can be spread from normal soap dispenser. If used automatic soap dispenser it can we stop spreading covid-19. it is best way to sanitize your hand. Be safe and be happy.

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Google Home using NodeMCU, DHT11, MQ2(Smoke Detector), Blynk, Touch sensor, I2C display and IFTTT.

electric creator 2020-08-26 | Voice controlled Home Automation with Google Assistant-IFTTT-BLYNK
IFTTT is a web based application to make weblinks .We link Google assistant with Blynk cloud using IFTTT to control devices using Voice commands.

I have used DHT11 or MQ2 sensor for measuring air quality of my room and mq2 to data will be sent to the e-mail if there will be gas,LPG or smoke leakage in your room.

I have also shown the components used, it's circuit diagram and almost everything that require to make this amazing project.

if you have not seen my previous videos please go and See my previous video the link is here:-
Part 1 - youtu.be/FSIZtjeRz0o

Part 2 - youtu.be/1hlHTzNQdiI

Part 3 - youtu.be/A0kfhzeXuRI

Material used:-
1).Nodemcu
2).DHT11
3).Zero board
4). IC 7805
5). 50x50mm 12V 0.1A Fan
6).Same jumper wires
7). 100uf Capacitor
8). 10uf Capacitor
9). Adaptor 12V-2A
10). push button
11). copper wire 1mm
12). Four Channel relay module
13).MQ2 or MQ135
14).IC7404
15).Buzzer 5v
16).heat sink
17).I2C display
18).Touch sensor
19).IC X-or(7486)

Nodemcu new display code link :-
drive.google.com/file/d/1Ysq4PqeE6EvfvJBs1wlZYQYGxtFM2KVA/view?usp=sharing

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Google Home using NodeMCU, DHT11, MQ2(Smoke Detector), Blynk, e-mail(Notif), I2C display and IFTTT.

electric creator 2020-08-20 | Voice controlled Home Automation with Google Assistant-IFTTT-BLYNK
IFTTT is a web based application to make weblinks .We link Google assistant with Blynk cloud using IFTTT to control devices using Voice commands.

I have used DHT11 or MQ2 sensor for measuring air quality of my room and mq2 to data will be sent to the e-mail if there will be gas,LPG or smoke leakage in your room.

I have also shown the components used, it's circuit diagram and almost everything that require to make this amazing project.

if you have not seen my previous videos please go and See my previous video the link is here:-

Part 1 - youtu.be/FSIZtjeRz0o

Part 2 - youtu.be/1hlHTzNQdiI

Part4 :- youtu.be/wst737jqWnk

Material used:-
1).Nodemcu
2).DHT11
3).Zero board
4). IC 7805
5). 50x50mm 12V 0.1A Fan
6).Same jumper wires
7). 100uf Capacitor
8). 10uf Capacitor
9). Adaptor 12V-2A
10). push button
11). copper wire 1mm
12). Four Channel relay module
13).MQ2 or MQ135
14).IC7404
15).Buzzer 5v
16).heat sink
17).I2C display

Nodemcu new display code link :-
drive.google.com/file/d/1Ysq4PqeE6EvfvJBs1wlZYQYGxtFM2KVA/view?usp=sharing

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Google Home using NodeMCU, DHT11, MQ2(Smoke Detector), Blynk, e-mail(Notification) and IFTTT.

electric creator 2020-08-16 | Voice controlled Home Automation with Google Assistant-IFTTT-BLYNK
IFTTT is a web based application to make weblinks .We link Google assistant with Blynk cloud using IFTTT to control devices using Voice commands.

I have used DHT11 or MQ2 sensor for measuring air quality of my room and mq2 to data will be sent to the e-mail if there will be gas,LPG or smoke leakage in your room.

I have also shown the components used, it's circuit diagram and almost everything that require to make this amazing project.

if you have not seen my previous or future videos please go and See my previous video the link is here:-

Part 1 : - youtu.be/FSIZtjeRz0o

Part 3 :- youtu.be/A0kfhzeXuRI

Part4 :- youtu.be/wst737jqWnk

Material used:-
1).Nodemcu
2).DHT11
3).Zero board
4). IC 7805
5). 50x50mm 12V 0.1A Fan
6).Same jumper wires
7). 100uf Capacitor
8). 10uf Capacitor
9). Adaptor 12V-2A
10). push button
11). copper wire 1mm
12). Four Channel relay module
13).MQ2 or MQ135
14).IC7404
15).Buzzer 5v
16).heat sink

Nodemcu new code link :-
drive.google.com/file/d/1j04HBJCzyB-oU4Wf-0fvEzmvemr3tElJ/view?usp=sharing

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Google Home using NodeMCU, Blynk,DHT11 and IFTTT

electric creator 2020-08-13 | Voice controlled Home Automation with Google Assistant-IFTTT-BLYNK
IFTTT is a web based application to make weblinks .We link Google assistant with Blynk cloud using IFTTT to control devices using Voice commands.

I have also shown the components used, it's circuit diagram and almost everything that require to make this amazing project.
If you want to see update in nodemcu with sensor or display go and see my future video

Part 2 :- youtu.be/1hlHTzNQdiI

Part 3 :- youtu.be/A0kfhzeXuRI

Part4 :- youtu.be/wst737jqWnk

Material used:-
1).Nodemcu
2).DHT11
3).Zero board
4). IC 7805
5). 50x50mm 12V 0.1A Fan
6).Same jumper wires
7). 100uf Capacitor
8). 10uf Capacitor
9). Adaptor 12V-2A
10). push button
11). copper wire 1mm
12). Four Channel relay module

Nodemcu code link :-
drive.google.com/file/d/10VbtMPkakxNA7_Wejk_oHEg6BR4h_kYH/view?usp=sharing

Thank you for watching this video
And please Like, Comment, Share & Subscribe My Channel Which is electric creator.

Wireless robot using a Lora module part - 2, longest range 4km.

electric creator 2020-07-01 | It will work as a bomb diffuser,
lab assistant or for security purpose.

it required lots of knowledge and I am working from 6 month.

Please help for FPV camera and FPV receiver.

And please save someone give idea for gripper how I can increase the mechanical strength of gripper so that I can improve my design.

part - 1
youtu.be/WVNXE7x2POA

Please Subscribe