Uploaded September 2019 | Updated September 2026, 5 hours ago
When Hell Decides To Visit
Internally it utilizes original Nintendo 64 hardware for the main system and several custom components and 3D printed parts to make up the rest of it.
Originally this system was a commission for a buyer, but there was an unfortunate paint failure that happened very far into the project and it essentially made starting over an easier option.
Because of this, I decided I would finish off this project, but it is as basic as a portable system can get and though it is solid, it's not without its flaws.
However, this does present an opportunity for those who would like to get into console modding or those who already know what they are doing to add the features this lacks.
System Specs:
- Original N64 Motherboard, Cartridge Based System
- Standard Jumper Pak (Expansion Pak Required for Games like Donkey Kong 64)
- Custom Controller Board, but no built-in Memory Card or External Connector. The option to hard-wire a Memory Card to the Controller Board is possible. (Not Included)
- Battery Power Only - 2 3.7v 5000mAh Li-Po batteries with Smart Charger. The option for Wall Power is possible via the HDMI connector and a Breakout Box. (Not Included)
- Single Player Only - The option for multi-player is possible via the HDMI connector and a Breakout Box (Not Included)
- 5" 4:3 Aspect Ratio Screen - The option for A/V out is possible via the HDMI connector and a Breakout Box (Not Included)
- Stereo Speaker Output with Custom Amp and Headphone Jack.
Overall the system handles great and the controls work beautifully, with the exception of the D-Pad. It does work but is very stiff. Fortunately not many games used it, but if you're wanting to play a game that requires it, it will take some modification to make work.
NOTE ABOUT THE BREAKOUT BOX & MEMORY CARD "OPTIONS":
What this means is that original commission was going to be fully loaded with A/V Out, Play & Charge, Multi-Player and Internal Memory abilities. However, when the project was scrapped, the internals had not been wired up yet and the connections from the N64 to the HDMI connector were never made. On top of this, certain components like the Power Management board and Controller Board with Built-In memory were no longer going to be used as they are expensive and still needed to be used for the original customers project. So this made this console a very basic system all around.
That being said, the options are technically there to be wired up, but as-is will not work. Again, if you are skilled with soldering/modding you can implement these options, but it would be a project.
If you are interested in getting into the console modding hobby or are looking for someone who can do the modifications for you, please visit the Bit Built as it's a very good place to start!
bitbuilt.net/forums/index.php
When Hell Decides To Visit
Internally it utilizes original Nintendo 64 hardware for the main system and several custom components and 3D printed parts to make up the rest of it.
Originally this system was a commission for a buyer, but there was an unfortunate paint failure that happened very far into the project and it essentially made starting over an easier option.
Because of this, I decided I would finish off this project, but it is as basic as a portable system can get and though it is solid, it's not without its flaws.
However, this does present an opportunity for those who would like to get into console modding or those who already know what they are doing to add the features this lacks.
System Specs:
- Original N64 Motherboard, Cartridge Based System
- Standard Jumper Pak (Expansion Pak Required for Games like Donkey Kong 64)
- Custom Controller Board, but no built-in Memory Card or External Connector. The option to hard-wire a Memory Card to the Controller Board is possible. (Not Included)
- Battery Power Only - 2 3.7v 5000mAh Li-Po batteries with Smart Charger. The option for Wall Power is possible via the HDMI connector and a Breakout Box. (Not Included)
- Single Player Only - The option for multi-player is possible via the HDMI connector and a Breakout Box (Not Included)
- 5" 4:3 Aspect Ratio Screen - The option for A/V out is possible via the HDMI connector and a Breakout Box (Not Included)
- Stereo Speaker Output with Custom Amp and Headphone Jack.
Overall the system handles great and the controls work beautifully, with the exception of the D-Pad. It does work but is very stiff. Fortunately not many games used it, but if you're wanting to play a game that requires it, it will take some modification to make work.
NOTE ABOUT THE BREAKOUT BOX & MEMORY CARD "OPTIONS":
What this means is that original commission was going to be fully loaded with A/V Out, Play & Charge, Multi-Player and Internal Memory abilities. However, when the project was scrapped, the internals had not been wired up yet and the connections from the N64 to the HDMI connector were never made. On top of this, certain components like the Power Management board and Controller Board with Built-In memory were no longer going to be used as they are expensive and still needed to be used for the original customers project. So this made this console a very basic system all around.
That being said, the options are technically there to be wired up, but as-is will not work. Again, if you are skilled with soldering/modding you can implement these options, but it would be a project.
If you are interested in getting into the console modding hobby or are looking for someone who can do the modifications for you, please visit the Bit Built as it's a very good place to start!
bitbuilt.net/forums/index.php
