3D Maker Noob | PID Tuning In 10 Easy Steps @3DMakerNoob | Uploaded December 2019 | Updated October 2024, 23 hours ago.
Testing out to see what the response is for these quick instructional video. They are short and straight to the point. Let me know if you guys want to see more!
Steps Below:
Step 1: Open Pronterface
Step 2: Connect USB cable to printer and PC
Step 3: Switch on 3D Printer
Step 4: Connect to the printer through Pronterface
Step 5: In the command line enter: "M303 S215 C10" - Hit Enter
Step 6: Make Beverage
Step 7: Take note of the Kp values displayed in Pronterface
Step 8: Input the PID values through the command line: "M301 Pxx.xx Ix.xx Dxx.xx" - (xx.xx represent the Kp Ki and Kd values) - Hit Enter
Step 9: In the command line enter: "M500"
Step 10: Disconnect Printer
Should you wish to support me, you can do so via:
Patreon: patreon.com/3Dmakernoob
paypal: paypal.me/jcasha
Want to send me something? go ahead (Normal mail as courier packages get returned):
Attn: Joseph Casha
P.O. Box 12
Constitution Street,
Mosta, MST 9059
Malta
Europe
#3DMNShorts
-----------
✌✌Affiliate Links ✌✌
Matterhackers: geni.us/MH3DMN
Amazon International: geni.us/3DMNoob
Gearbest: geni.us/3DMNGB
Banggood: geni.us/3DMNBG
Aliexpress: geni.us/3DMNAE
Recording Equipment:
Main Camera: Panasonic Lumix G7: geni.us/LumixG7
(B-Roll) Canon EOS760D: geni.us/CanonEOS
Canon EF 10-18mm: geni.us/CanonEF1018
Canon Lens: geni.us/Canon2470
ElGato Stream Deck: geni.us/Streamdeck
Elgato HD60S Capture Card: geni.us/elgatohd60
Timelapse - GoPro Hero 5: geni.us/GoProH5
Microphone, Rode Filmmaker Kit: geni.us/RodeFMkit
Light Boxes: geni.us/StudioLights
High Speed SD Card: geni.us/SandiskSD
Testing out to see what the response is for these quick instructional video. They are short and straight to the point. Let me know if you guys want to see more!
Steps Below:
Step 1: Open Pronterface
Step 2: Connect USB cable to printer and PC
Step 3: Switch on 3D Printer
Step 4: Connect to the printer through Pronterface
Step 5: In the command line enter: "M303 S215 C10" - Hit Enter
Step 6: Make Beverage
Step 7: Take note of the Kp values displayed in Pronterface
Step 8: Input the PID values through the command line: "M301 Pxx.xx Ix.xx Dxx.xx" - (xx.xx represent the Kp Ki and Kd values) - Hit Enter
Step 9: In the command line enter: "M500"
Step 10: Disconnect Printer
Should you wish to support me, you can do so via:
Patreon: patreon.com/3Dmakernoob
paypal: paypal.me/jcasha
Want to send me something? go ahead (Normal mail as courier packages get returned):
Attn: Joseph Casha
P.O. Box 12
Constitution Street,
Mosta, MST 9059
Malta
Europe
#3DMNShorts
-----------
✌✌Affiliate Links ✌✌
Matterhackers: geni.us/MH3DMN
Amazon International: geni.us/3DMNoob
Gearbest: geni.us/3DMNGB
Banggood: geni.us/3DMNBG
Aliexpress: geni.us/3DMNAE
Recording Equipment:
Main Camera: Panasonic Lumix G7: geni.us/LumixG7
(B-Roll) Canon EOS760D: geni.us/CanonEOS
Canon EF 10-18mm: geni.us/CanonEF1018
Canon Lens: geni.us/Canon2470
ElGato Stream Deck: geni.us/Streamdeck
Elgato HD60S Capture Card: geni.us/elgatohd60
Timelapse - GoPro Hero 5: geni.us/GoProH5
Microphone, Rode Filmmaker Kit: geni.us/RodeFMkit
Light Boxes: geni.us/StudioLights
High Speed SD Card: geni.us/SandiskSD