Uploaded August 2017 | Updated November 2026, 1 hour ago
Part 5 is finally here! First we measured the compression ratio using a syringe and water. Then we made a new head gasket out of annealed 12AWG(0.0808 in)(2.05 mm) copper house wire. Then we soldered the ends together to make a continuous loop that would make a good seal. We then drilled a third hole in the cylinder which is the intake port(the carburetor will eventually be mounted on this hole). Then the most exciting part, I squirted some fuel into the intake after hooking the spark plug up to an neon sign transformer and used a piece of rope to start it. It sounds like an angry weed eater!!!
BTW sorry for the long delay in posting this video. I have been very busy. I was helping out a lot at my local makerspace, HackPGH. I was helping build a flying machine for the Red Bull Flutag. I was the pilot. Good thing I didn't die! If you noticed the scratch on my head in the closing that was from my craft.
Why? Because it will be a challenge and I like a little challenge. The main constraints that I have put on this project are limited power tools. I will only use a battery drill, hacksaw, and other common hand tools and materials. Working with constraints are what real world engineers basically do and I find it challenging and fun working in this way. There are three reason for trying to do this with minimal tools: 1. so anyone, even someone in a third world country can replicate. 2. to show what you might be able to do in an apocalyptic situation. 3. creative thinking. I hope you enjoy. Please leave ideas and suggestions in the comments below!
Instagram and Facebook for project updates, and pictures of casting, making, hacking, building, and more!
instagram.com/makerj101
facebook.com/makerj101
Keep exploramenting and thank you for watching!
Don't forget to subscribe for more! youtube.com/user/makerj101?sub_confirmation=1firmation=1
Part 5 is finally here! First we measured the compression ratio using a syringe and water. Then we made a new head gasket out of annealed 12AWG(0.0808 in)(2.05 mm) copper house wire. Then we soldered the ends together to make a continuous loop that would make a good seal. We then drilled a third hole in the cylinder which is the intake port(the carburetor will eventually be mounted on this hole). Then the most exciting part, I squirted some fuel into the intake after hooking the spark plug up to an neon sign transformer and used a piece of rope to start it. It sounds like an angry weed eater!!!
BTW sorry for the long delay in posting this video. I have been very busy. I was helping out a lot at my local makerspace, HackPGH. I was helping build a flying machine for the Red Bull Flutag. I was the pilot. Good thing I didn't die! If you noticed the scratch on my head in the closing that was from my craft.
Why? Because it will be a challenge and I like a little challenge. The main constraints that I have put on this project are limited power tools. I will only use a battery drill, hacksaw, and other common hand tools and materials. Working with constraints are what real world engineers basically do and I find it challenging and fun working in this way. There are three reason for trying to do this with minimal tools: 1. so anyone, even someone in a third world country can replicate. 2. to show what you might be able to do in an apocalyptic situation. 3. creative thinking. I hope you enjoy. Please leave ideas and suggestions in the comments below!
Instagram and Facebook for project updates, and pictures of casting, making, hacking, building, and more!
instagram.com/makerj101
facebook.com/makerj101
Keep exploramenting and thank you for watching!
Don't forget to subscribe for more! youtube.com/user/makerj101?sub_confirmation=1firmation=1



![Running My Homemade Steam Engine on Live Steam From My New Homemade Boiler
Here is my steam engine finally running on real steam! So it is officially a steam engine now! In the beginning I had problems with the piston binding. I thought at first it was because of the oil mixing with steam in the cylinder and making a sticky paste. But even after I cleaned it all out it still binded up. I then sanded the epoxy putty piston down to make it a little smaller. Then it worked great! This is because the thermal expansion coefficient of epoxy is much greater than the thermal expansion coefficient for copper.
The thermal expansion coefficient of JB Weld(essentially what my piston is made out of) is: 48 [(in)/(in) x °F)] x 10(-6) http://www.mombu.com/aviation/aviators/t-epoxy-bonding-to-aluminum-and-magnesium-3587575.html
The thermal expansion coefficient of copper is a mere 9.3 [(in)/(in) x °F)] x 10(-6). http://www.engineeringtoolbox.com/linear-expansion-coefficients-d_95.html
So a huge difference there in thermal expansion coefficients. Explains everything! Optimally I should make the piston and cylinder out of materials that have similar or the same thermal expansion coefficients.
Disclaimer: WARNING! Steam boilers are EXTREMELY DANGEROUS! If you blow yourself up because you tried something I did in this video. I AM NOT LIABLE. If you try anything in this video you do so at YOUR OWN RISK. So dont come whining at me if you get a tomato sauce can(or other boiler shrapnel) permanently embedded in you or all your skin falls off from a steam burn. I warned you. I encourage you to experiment as I am but please be safe and smart and remember that I am not liable for your actions. Thanks!
Thank you for watching! Running My Homemade Steam Engine on Live Steam From My New Homemade Boiler](https://i.ytimg.com/vi/kcHVOlkaJ0I/mqdefault.jpg)






