Joshua Bardwell | OpenIPC is ... here? // Emax Wyvern & Runcam WifiLink @JoshuaBardwell | Uploaded 1 week ago | Updated 4 hours ago
Uncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST: fpvknowitall.com/ultimate-fpv-shopping-list
SUPPORT ME ON PATREON at: http://bit.ly/2Ep5Sia
THIS IS MY FULL TIME JOB. Here are other ways that you can support me: fpvknowitall.com/support-me
---
I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.
Buy the Runcam WifiLink at:
* GetFPV - bit.ly/3Y509qf
* NewBeeDrone - bit.ly/3XQPlKR
* Runcam Store - bit.ly/3XNvble
By the Emax Wyvern at:
* Emax Store - bit.ly/4gNecIk
MANDATORY DISCLAIMER: I am a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites.
---
00:00:00 - OpenIPC is HUGE
00:01:50 - There are TWO systems being reviewed in this video
00:02:41 - Why is it shaped like this?! (Runcam)
00:03:49 - This is NOT finished hardware
00:04:27 - Disclaimer: I'm an OpenIPC newbie
00:05:07 - Runcam: overview of the video transmitter
00:06:59 - Emax: vTX Overview
00:07:47 - Emax: a nano-sized vTX for whoops!
00:08:21 - Emax video receiver
00:09:27 - No HDMI out?!
00:10:41 - Runcam: video receiver
00:10:46 - Latency
Mads Tech's channel is: youtube.com/channel/UCxpgzA0iO-7anEAyiLMDRmg
00:13:54 - Why only 4 Mbps?!
00:14:20 - No channel change or auto scan
00:15:31 - My flight test setup
00:17:30 - Emax Flight Test
00:23:44 - Runcam Flight Test
00:28:56 - Conclusion
Mario FPV's YouTube is the main source for info about OpenIPC: youtube.com/channel/UCX2UiZjg485tDoq_Yl4Pysw
OpenIPC project website: openipc.org
Uncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST: fpvknowitall.com/ultimate-fpv-shopping-list
SUPPORT ME ON PATREON at: http://bit.ly/2Ep5Sia
THIS IS MY FULL TIME JOB. Here are other ways that you can support me: fpvknowitall.com/support-me
---
I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.
Buy the Runcam WifiLink at:
* GetFPV - bit.ly/3Y509qf
* NewBeeDrone - bit.ly/3XQPlKR
* Runcam Store - bit.ly/3XNvble
By the Emax Wyvern at:
* Emax Store - bit.ly/4gNecIk
MANDATORY DISCLAIMER: I am a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites.
---
00:00:00 - OpenIPC is HUGE
00:01:50 - There are TWO systems being reviewed in this video
00:02:41 - Why is it shaped like this?! (Runcam)
00:03:49 - This is NOT finished hardware
00:04:27 - Disclaimer: I'm an OpenIPC newbie
00:05:07 - Runcam: overview of the video transmitter
00:06:59 - Emax: vTX Overview
00:07:47 - Emax: a nano-sized vTX for whoops!
00:08:21 - Emax video receiver
00:09:27 - No HDMI out?!
00:10:41 - Runcam: video receiver
00:10:46 - Latency
Mads Tech's channel is: youtube.com/channel/UCxpgzA0iO-7anEAyiLMDRmg
00:13:54 - Why only 4 Mbps?!
00:14:20 - No channel change or auto scan
00:15:31 - My flight test setup
00:17:30 - Emax Flight Test
00:23:44 - Runcam Flight Test
00:28:56 - Conclusion
Mario FPV's YouTube is the main source for info about OpenIPC: youtube.com/channel/UCX2UiZjg485tDoq_Yl4Pysw
OpenIPC project website: openipc.org