Mechanics Carport Driveway Shade Tarp @keithnoneya
Mechanics Carport Driveway Shade Tarp  @keithnoneya
Uploaded September 2016 | Updated November 2026, 1 day ago
Description: Here's my Shade Tarp I made for working in front of my garage. I use it for doing mechanic work, wood working or any kind of work in front of my garage where I could use some shade. I live in southern Louisiana and it gets HOT here. Mid-summer can be in the mid to upper 90's with 100% humidity. So working on the driveway with the white concrete can really be bright, and very hot to lie down on. Also tools lying in the sun on the concrete get extremely hot, too hot to handle. The Tarp fixed a lot of my issues and it takes about 5-10 minutes to set it up and the same to take it down, fold up and put away. The Tarp also solved some of the light rain pop ups we have here as well. This system is not meant to be left up in winds over 10mph or you risk it tearing in the center hole where the boom hook goes through.
** Ground Poles. I initially I tried 2" x 2" x 8' foot poles mounted in pipes with holes in the ground. I used Eye Bolts on top to bungee the tarp to. The holes in the ground would constantly fill up with water & debris, so it became a constant battle to clean them out, so I found it easier to just bungee them to the car door handles or the frame on the bottom of the car. The poles also made it harder to open the car doors on the driveway sides. One issue with anchoring to the car is, it can’t be moved until the job is done or you take the tarp down or find an alternate anchor point for the tarp ends.

List of materials:
- QTY One 15' x 12' 8 or 10 oz Canvas Painters Tarp/Drop Cloth Lowes 8oz $31.98
Don't use the plastic tarps they will only last a short time outside as the sun will tear them up FAST. My Thompson Sealed Canvas has been used for 10 years now. I take it down when I'm not using it so the wind and sun don't tear it up.
- Qty One Tarpaulin Repair Kit eBay item number 400851762695 $8.89
- Qty 15 Galvanized #6 Nails or screw in Stainless hooks.
- Qty Two 2" x 2" x 8' Square Poles. Lowes $1.89 One for the Boom & one for the Cross Bar. The Cross Bar upgrade, it's not shown in this video, but it's at the end of my in my Ford F250 F350 7 3L Belt Tensioner video at time index 3:14 youtube.com/watch?v=Ntjy8id0AyE
- Qty Five Stainless "Eye" Bolts. Lowes Three for Garage, one for the Boom Pole and one for the Cross Bar. These come in 3 per pack, you'll need to packs.
- Qty Two Stainless Hook Bolts. Lowes $1.01 One for the Boom & one for the Cross Bar.
- Qty Two Pulleys Lowes $3.48
- Qty One Line Clamp or Clevis. Lowes $1.67
- Qty Four 2 foot Bungy Cords. Lowes 2 pack $3.58
- 1/16" Heavy duty Twine to tie loops into the Tarp Corners.
- 4.5" Boat Cleat to anchor robe. Lowes $0.99
- Two 1-5/8" Deck or Fence Screws to Anchor Boat Cleat to side of Garage Door Frame.
- 30' 3/8 Polyester Stable Braided Rope for pulley system. Note: *** After you run the rope through the top pulley at the peak, tie the rope to the hook and clamp on the Eye Bolt on the “Garage Door Frame” 1:19. Pull the rope tight, then note the rope length between the pulley and the Eye Bolt. Pull the rope down to the spot where it goes into the pulley and I suggest you tie a knot in the rope at that point. This is so if you forget to clamp the clamp to the Eye Bolt when you pull the rope, the clamp won’t go all the way up to the pulley at the peak of the roof. If that happens you’ll need a ladder to get it back down. You can see this knot in the video at time index; 1:04.

Chemical Used:
- 2 Gallons of Thompsons WaterSeal Clear Multi-Surface Low Voc PN: TH.024101-16 Lowes Item #236342 $15.98 gal ea.

Tools Used:
- Large 6-9" Needle Nose Pliers. Bend the nails into hooks after put into the garage door upper frame board.
- Carpenters Hammer. for nails, & punch holes in the tarp and set the Eyelets.
- Barbecue Lighter to Melt the ends of the Nylon Rope so that it won't come undone.
- Drill Set. Drill Pilot holes in the Wood Jib Pole and Garage Frame Boards for Eye Bolts.
- 3/8" Electric Hand Drill to, you guessed it Drill holes. LOL
- 2 Gal Chemical Sprayer, to spray sealer on canvas. Lowes $21.97
- No. 2 Phillips screw driver. To spread the Eye Bolts to mount the Pulleys into the eyes, then use the needle nose to hold the Eye Bolts while you hammer the Eye Bolts closed around the end of the Pulley Eyes. After you assemble the pulley and eye bolts use the screw driver to screw the eye bolts into the garage frame where you drilled a pilot hole. Make sure you drill the holes quite a bit smaller than the threads on the Eye Bolts but not smaller than the metal shaft the threads are cast into or they will come loose.

If you see something I missed in the description, drop a comment and I'll include it.
I hope you all enjoy the video and found it useful. If you did find it useful, please give it a thumbs up to let me know my work is appreciated. Also it helps my channel if you subscribe, even if you never come back. So if you'd like to help me please subscribe.
Thanks for watching.
Best Wishes & Blessings Keith Noneya
Mechanics Carport Driveway Shade TarpEASY Caravan Wiper Assy Removal for Spark Plugs or Rear Engine Access 2002Picture CNC Building Mess AHHHHHow to Remove a Stuck Rotor on 99-03 F250 or F350 SRW95 Pathfinder D21 No Start Crank or Dash lights Fix Most Likely Solution Part 12003 Cadillac CTS Drivers Mid Quarter Panel Part 27 ofUnboxing an Eastwood 175 Mig Welder w Spool Gun Unboxing ONLY2003 Cadillac CTS Quarter Panel Roof Rail Update Part 19 of99 03 Driver 7_3 PS Valve Cover Breather Factory Clamp Removal2003 Cadillac CTS Drivers Quarter Panel Part 22 of2003 Cadillac CTS Drivers Quarter Grey Primer Gone Part 33 of2003 Cadillac CTS Drivers Quarter Body Metal Prep Part 6  of
Keith Noneya |

Mechanics Carport Driveway Shade Tarp

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER