Uploaded April 2023 | Updated September 2026, 4 days ago
😎 Get your FREE FDM 3D Printing Glossary Here:
itsmeadmade.myflodesk.com/glossary
In this video, I'll show you how to use Ultimaker Cura 5's bed adhesion settings to improve the first layer adhesion of your 3D prints. A good first layer is essential for a successful print, and using the right bed adhesion technique can prevent warping, lifting, or shifting during printing.
First, I'll explain the differences between skirts, brims, and rafts, which are the most common bed adhesion techniques in 3D printing. Skirts are thin lines printed around the model's perimeter, brims are wider flat structures printed around the model's base, and rafts are complete platforms printed under the model, providing a more stable surface for the first layer.
Next, I'll guide you through Ultimaker Cura 5's settings for skirts, brims, and rafts, including the number of lines, distance from the model, and overlap settings. I'll also show you how to adjust the extrusion width and nozzle temperature to improve the first layer's bonding with the bed.
00:00 - Intro
00:25 - Beginner Disclaimer
01:20 - Build Plate Adhesion
02:21 - PRO TIP!
03:18 - What are Skirts?
05:13 - Skirt Line Count Setting
06:30 - PRO TIP!
06:49 - Skit Distance Setting
07:16 - Skirt/Brim Minimum Length
08:46 - Brim = More Adhesion
09:42 - Skirt/Brim Minimum Length
10:04 - Brim Width & Brim Line Count Settings
11:05 - Brim Distance Setting
12:06 - Brim Only on Outside
13:20 - Brim Replaces Supports Setting
15:21 - What are Rafts?
16:30 - Raft Settings
17:02 - Raft Extra Margin Setting
18:11 - Raft Smoothing Setting
20:27 - Air Gap Setting
22:23 - Printed Air Gap Examples
28:18 - Initial Z Overlap Setting
29:51 - 3 Parts of a Raft
30:21 - Raft Top Layers
31:04 - Raft Top Layer Thickness Setting
31:28 - Raft Top Line Width Setting
31:46 - Raft Top Spacing Setting
32:16 - Raft Middle Layers Setting
32:47 - Raft Middle Thickness Setting
33:13 - Raft Middle Line Width Setting
33:38 - Raft Middle Spacing Setting
34:50 - Raft Base Thickness Setting
35:25 - Raft Base Line Width Setting
36:03 - Raft Base Line Spacing Setting
38:00 - Raft Print Speed Setting
38:48 - Raft Top Print Speed Setting
38:58 - Raft Middle Print Speed Setting
39:06 - Raft Base Print Speed Setting
40:14 - Raft Fan Speed Settings
41:20 - THANK YOU!
42:07 - What you now know!
42:38 - Join the Community!
42:57 - Conclusion
43:22 - Chris’ Extras
DISCLAIMER: This video is not sponsored. Some of the links are affiliate links in which I will receive a small commission.
😎 Get your FREE FDM 3D Printing Glossary Here:
itsmeadmade.myflodesk.com/glossary
In this video, I'll show you how to use Ultimaker Cura 5's bed adhesion settings to improve the first layer adhesion of your 3D prints. A good first layer is essential for a successful print, and using the right bed adhesion technique can prevent warping, lifting, or shifting during printing.
First, I'll explain the differences between skirts, brims, and rafts, which are the most common bed adhesion techniques in 3D printing. Skirts are thin lines printed around the model's perimeter, brims are wider flat structures printed around the model's base, and rafts are complete platforms printed under the model, providing a more stable surface for the first layer.
Next, I'll guide you through Ultimaker Cura 5's settings for skirts, brims, and rafts, including the number of lines, distance from the model, and overlap settings. I'll also show you how to adjust the extrusion width and nozzle temperature to improve the first layer's bonding with the bed.
00:00 - Intro
00:25 - Beginner Disclaimer
01:20 - Build Plate Adhesion
02:21 - PRO TIP!
03:18 - What are Skirts?
05:13 - Skirt Line Count Setting
06:30 - PRO TIP!
06:49 - Skit Distance Setting
07:16 - Skirt/Brim Minimum Length
08:46 - Brim = More Adhesion
09:42 - Skirt/Brim Minimum Length
10:04 - Brim Width & Brim Line Count Settings
11:05 - Brim Distance Setting
12:06 - Brim Only on Outside
13:20 - Brim Replaces Supports Setting
15:21 - What are Rafts?
16:30 - Raft Settings
17:02 - Raft Extra Margin Setting
18:11 - Raft Smoothing Setting
20:27 - Air Gap Setting
22:23 - Printed Air Gap Examples
28:18 - Initial Z Overlap Setting
29:51 - 3 Parts of a Raft
30:21 - Raft Top Layers
31:04 - Raft Top Layer Thickness Setting
31:28 - Raft Top Line Width Setting
31:46 - Raft Top Spacing Setting
32:16 - Raft Middle Layers Setting
32:47 - Raft Middle Thickness Setting
33:13 - Raft Middle Line Width Setting
33:38 - Raft Middle Spacing Setting
34:50 - Raft Base Thickness Setting
35:25 - Raft Base Line Width Setting
36:03 - Raft Base Line Spacing Setting
38:00 - Raft Print Speed Setting
38:48 - Raft Top Print Speed Setting
38:58 - Raft Middle Print Speed Setting
39:06 - Raft Base Print Speed Setting
40:14 - Raft Fan Speed Settings
41:20 - THANK YOU!
42:07 - What you now know!
42:38 - Join the Community!
42:57 - Conclusion
43:22 - Chris’ Extras
DISCLAIMER: This video is not sponsored. Some of the links are affiliate links in which I will receive a small commission.
