Uploaded May 2026 | Updated September 2026, 2 weeks ago
In this video, I show how I created a universal magnetic peg holder system for cribbage boards using my CNC machine and laser. This hidden peg storage method works great even on thinner cribbage boards. It can actually work on boards only 5/8” thick.
I walk through:
👉 Designing the peg holder in VCarve
👉 Testing pocket depths and magnet sizing
👉 Creating a reusable alignment template
👉 CNC toolpaths for the lid pocket, magnets, peg storage, and finger pull
👉 Using magnets and steel plates for secure hidden storage
👉 Tips for avoiding tear out with downcut bits
👉 How to install everything cleanly
This method makes it easy to place peg storage anywhere on the back of a cribbage board while maintaining a clean professional look.
If you watch the full video I will share with you how you can receive the file for this project for free by going to my website and putting in the coupon code I share in the video.
If wanting the file but not interested in getting the file for free it can be purchased on my website at the following link:
robsandstromdesigns.com/product/cribbage-board-peg-holder
⏰ TimeStamps. ⏰
00:00 Introduction
00:40 Why Peg Storage Matters
01:30 The Magnetic Steel Plate Concept
03:05 Designing the Peg Holder in VCarve
05:10 Setting Up the Lid Pocket Toolpath
07:00 Magnet Pocket Design & Testing
09:00 Peg Pocket Toolpath Setup
11:20 Creating the Finger Pull with Fluting Toolpath
13:30 Test Cuts & Adjustments
15:20 Making a Laser Alignment Template
17:40 Positioning the Peg Holder on the Board
19:00 CNC Cutting the Final Board
21:10 Installing Magnets & Testing Fit
23:00 Final Results & Demonstration
24:15 Wrap Up
TOOLS & MATERIALS USED WITH LINKS::
This video is not sponsored. The following links may be affiliate links. By using these links you are supporting this channel. Thank you.
IDC Woodcraft Downcut Ball Nose Bit: idcwoodcraft.com/products/1-4-ball-nose-downcut?_pos=1&_sid=c6d8cfc80&_ss=r
CIC Workshop Bowl & Tray Bit: cicworkshop.com/products/7-16x5-16-bowl-tray-1-4-shank-se1370?sca_ref=7158192.YJVxMOI6w9sj
CIC Workshop1/8" Downcut Endmill: cicworkshop.com/products/1-8x1-2-downcut-spiral-endmill-1-4-shank-srd203?sca_ref=7158192.YJVxMOI6w9sj
Starbond CA Glue: starbond.com/?rfsn=7955313.9020a2&utm_source=refersion&utm_medium=affiliate&utm_campaign=7955313.9020a2
N42 2x6mm Rare Earth Magnets: amzn.to/4xc0HdB
Steel Plates: totalelement.com/products/2-inch-steel-disc-blank-metal-strike-plates-60-pack
If you enjoy woodworking, CNC projects, cribbage boards, laser engraving, and maker content, consider subscribing for more tutorials and shop projects.
Laguna IQ CNC
Vectric vCarve Pro Software
====================
Connect with me !
====================
Website: robsandstromdesigns.com
Instagram: instagram.com/robsandstrom
Facebook: facebook.com/robsandstrom1
In this video, I show how I created a universal magnetic peg holder system for cribbage boards using my CNC machine and laser. This hidden peg storage method works great even on thinner cribbage boards. It can actually work on boards only 5/8” thick.
I walk through:
👉 Designing the peg holder in VCarve
👉 Testing pocket depths and magnet sizing
👉 Creating a reusable alignment template
👉 CNC toolpaths for the lid pocket, magnets, peg storage, and finger pull
👉 Using magnets and steel plates for secure hidden storage
👉 Tips for avoiding tear out with downcut bits
👉 How to install everything cleanly
This method makes it easy to place peg storage anywhere on the back of a cribbage board while maintaining a clean professional look.
If you watch the full video I will share with you how you can receive the file for this project for free by going to my website and putting in the coupon code I share in the video.
If wanting the file but not interested in getting the file for free it can be purchased on my website at the following link:
robsandstromdesigns.com/product/cribbage-board-peg-holder
⏰ TimeStamps. ⏰
00:00 Introduction
00:40 Why Peg Storage Matters
01:30 The Magnetic Steel Plate Concept
03:05 Designing the Peg Holder in VCarve
05:10 Setting Up the Lid Pocket Toolpath
07:00 Magnet Pocket Design & Testing
09:00 Peg Pocket Toolpath Setup
11:20 Creating the Finger Pull with Fluting Toolpath
13:30 Test Cuts & Adjustments
15:20 Making a Laser Alignment Template
17:40 Positioning the Peg Holder on the Board
19:00 CNC Cutting the Final Board
21:10 Installing Magnets & Testing Fit
23:00 Final Results & Demonstration
24:15 Wrap Up
TOOLS & MATERIALS USED WITH LINKS::
This video is not sponsored. The following links may be affiliate links. By using these links you are supporting this channel. Thank you.
IDC Woodcraft Downcut Ball Nose Bit: idcwoodcraft.com/products/1-4-ball-nose-downcut?_pos=1&_sid=c6d8cfc80&_ss=r
CIC Workshop Bowl & Tray Bit: cicworkshop.com/products/7-16x5-16-bowl-tray-1-4-shank-se1370?sca_ref=7158192.YJVxMOI6w9sj
CIC Workshop1/8" Downcut Endmill: cicworkshop.com/products/1-8x1-2-downcut-spiral-endmill-1-4-shank-srd203?sca_ref=7158192.YJVxMOI6w9sj
Starbond CA Glue: starbond.com/?rfsn=7955313.9020a2&utm_source=refersion&utm_medium=affiliate&utm_campaign=7955313.9020a2
N42 2x6mm Rare Earth Magnets: amzn.to/4xc0HdB
Steel Plates: totalelement.com/products/2-inch-steel-disc-blank-metal-strike-plates-60-pack
If you enjoy woodworking, CNC projects, cribbage boards, laser engraving, and maker content, consider subscribing for more tutorials and shop projects.
Laguna IQ CNC
Vectric vCarve Pro Software
====================
Connect with me !
====================
Website: robsandstromdesigns.com
Instagram: instagram.com/robsandstrom
Facebook: facebook.com/robsandstrom1
