Loose Radial Parts In, Taped Reel Out: S-300B #shorts @Smthelping
Loose Radial Parts In, Taped Reel Out: S-300B #shorts  @Smthelping
Uploaded November 2026 | Updated November 2026, 12 hours ago
Stop forming and taping radial components by hand. See how the S-300B fully automatic high-speed molding and taping machine from Southern Machinery works, in 3D from the real CAD model: loose LEDs, capacitors and resistors go in, formed, tested and sealed tape comes out, at 180 +/- 20 parts per minute.

How it works: a vibratory bowl orients loose radial parts onto a linear track. Walking-beam transfer clips carry each part station by station: the leads are spread, then pressed in an integrated forming die to 2.5, 3.5 or 5.0 mm pitch. Polarity is checked and a reversed part is turned 180 deg by a stepper-driven re-orientation clamp instead of being rejected. With the optional tester, capacitance and resistance are measured and failed parts drop into the reject chute. Leads are trimmed, good parts are placed onto 12.7 mm pitch paper tape, a heated top tape seals the leads, sprocket holes are punched and a servo indexer advances the tape one pitch at a time. The finished tape is folded into an ammo box or wound on a reel, ready for your radial inserter.
Key data (S-300B product sheet)
- Capacity: 180 +/- 20 pcs/min
- Body diameter: Ø4-Ø10 mm, two fixture sets (Ø4-6, Ø8-10)
- Formed lead pitch: 2.5 / 3.5 / 5.0 mm (7.5, 10, 15 mm and above to order)
- Hole pitch / hole diameter: 12.7 mm / 4.1 mm (other pitches on request)
- Taping height: 17-21 mm; product length 5-30 mm
- Packing: boxed (ammo) or coiled (reel)
- Servo control system replaces the traditional clutch
- Imported cams ground to 0.01 mm, design service life 15+ years
- Touch-screen operation, PLC or single-chip control
- 220 V / 50 Hz / 1.6 kW; air 4-5 kg/cm^2
Final configuration (fixtures, pitch, tester) is confirmed after reviewing your component list.

Chapters
00:00 Hand taping is the bottleneck
00:13 S-300B fully automatic molding & taping machine
00:28 Feed: vibratory bowl, linear track, transfer clips
00:40 Lead spread + integrated forming die (2.5 / 3.5 / 5.0 mm)
00:56 Polarity check, re-orientation, C/R value test, reject chute
01:12 Taping: 12.7 mm paper tape, heated top tape, punch, servo indexer
01:25 Packing: ammo box or reel
01:32 Servo drive and imported 0.01 mm cams
01:47 Specification
02:00 The result
02:09 Send us your component list

Machine geometry from the CAD model; components, paper and top tape, tape paths and motion timing shown illustratively, slowed for clarity in the close-ups.

Product page: smthelp.com
Contact: info@smthelp.com - WhatsApp +86 136 0256 2576
Southern Machinery, SMT & THT automation since 2011.
Subscribe: youtube.com/c/Smthelping

#THT #RadialTaping #PCBA #EMS #ElectronicsManufacturing #TapingMachine #Automation
Loose Radial Parts In, Taped Reel Out: S-300B #shortsOffline AOI for 01005 & 0.3 mm Pitch | SM-VT-980 by Southern Machinery2-in-1 X-Ray Component Counter & Inspection: See Hidden Broken WiresHow China made SFY03 AGV SMT Safety Guardian for Smart EMS factory PCB assemblyX-ray Component Counter Running Cost, Maintenance & ServiceWhy Is Your SMT Line Slow? #SMT #PCBAssembly #PCBConveyor #SMTAutomation #FactoryAutomationHow a Vibratory Bowl Feeder Works | SBF1001 Bulk Parts Feeder for SMT & THTX-ray Component Counter: Count 4 SMT Reels in 10 Seconds | X3100THT Automation Loop: Auto Insertion, Wave Soldering and AGV ReturnLED Insertion Machine Changeover in 6 Steps: Excel to ProductionOdd Form Insertion solution for Smart EMS factory PCB assemblyIndustrial Power Supply THT Solution: Terminals & Odd-Form Parts ROI
SMT solution provider |

Loose Radial Parts In, Taped Reel Out: S-300B #shorts

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER