Uploaded July 2026 | Updated November 2026, 2 hours ago
In this video, we'll show you how to install and start using the LitterHopper® for Litter-Robot® 5.
The Litter-Robot 5 LitterHopper® automatically monitors and refills litter to optimal levels, as needed, with a larger capacity, effortless install, and smarter app integration. Perfect for busy cat families and multi-cat homes.
🕒 Timestamps:
00:00 Introduction
00:31 Firmware Update
00:55 Preparation - Remove the Bonnet
01:09 Preparation - Remove the Globe, install key, reattach bonnet
02:47 Installing the LitterHopper
What's included with your LitterHopper:
LitterHopper
LitterHopper lid
Key things to know:
Litter is added only when needed and only during a clean cycle.
Your Litter-Robot 5 must be running firmware version 5.09.06 or later.
Once installed, LitterHopper is automatically detected and enabled.
Any time you add litter to the globe or the LitterHopper, press the Cancel button to zero the weight sensors for accurate operation.
Check your firmware:
Press and hold the Cancel and Connect buttons together for 3 seconds.
Confirm your Robot firmware is 5.09.06 or later.
You can also verify your firmware version in the Whisker app under your Litter-Robot 5 settings. If an update is needed, contact Whisker Customer Experience for assistance.
Prepare your Litter-Robot 5:
Ensure the unit is in the Home/Ready position.
Remove the bonnet by pressing both side latches and rotating it to about 45° before lifting it away.
If your unit has been used, clean the base and remove any litter or debris from the mounting pockets.
Remove the center plate from the bonnet by releasing the clips.
Reinstall the bonnet before attaching the LitterHopper.
Install the LitterHopper:
Verify the metal prong on the LitterHopper is clean and undamaged.
Align the LitterHopper posts with the circular mounting pockets on the back of the base.
Lower the LitterHopper into place.
Ensure the mounting tab is fully seated in the slot on the bonnet.
Check that there are no visible gaps between the LitterHopper, bonnet, or base.
The LCD screen will display "LitterHopper detected" when installation is successful.
Final setup:
Fill the globe to the MAX fill line and level the litter.
Fill the LitterHopper with fresh litter up to the MAX fill line and securely replace the lid.
Press the Cancel button to zero the weight sensors after adding litter.
Once detected, the LitterHopper is automatically enabled and ready to maintain your litter level.
Enable or disable LitterHopper:
From the control panel:
Press and hold the Cycle and Empty buttons for 3 seconds.
From the Whisker app:
Select your Litter-Robot 5 → Controls → LitterHopper → Enable or Disable.
Helpful Links:
LitterHopper Support Articles: litter-robot.com/support/article/litter-robot-5-litterhopper-installation-guide
Visit our Support Center: litter-robot.com/support
Warranty Information: litter-robot.com/explore/warranty.html
Follow Litter-Robot:
litter-robot.com
youtube.com/@LitterRobot
In this video, we'll show you how to install and start using the LitterHopper® for Litter-Robot® 5.
The Litter-Robot 5 LitterHopper® automatically monitors and refills litter to optimal levels, as needed, with a larger capacity, effortless install, and smarter app integration. Perfect for busy cat families and multi-cat homes.
🕒 Timestamps:
00:00 Introduction
00:31 Firmware Update
00:55 Preparation - Remove the Bonnet
01:09 Preparation - Remove the Globe, install key, reattach bonnet
02:47 Installing the LitterHopper
What's included with your LitterHopper:
LitterHopper
LitterHopper lid
Key things to know:
Litter is added only when needed and only during a clean cycle.
Your Litter-Robot 5 must be running firmware version 5.09.06 or later.
Once installed, LitterHopper is automatically detected and enabled.
Any time you add litter to the globe or the LitterHopper, press the Cancel button to zero the weight sensors for accurate operation.
Check your firmware:
Press and hold the Cancel and Connect buttons together for 3 seconds.
Confirm your Robot firmware is 5.09.06 or later.
You can also verify your firmware version in the Whisker app under your Litter-Robot 5 settings. If an update is needed, contact Whisker Customer Experience for assistance.
Prepare your Litter-Robot 5:
Ensure the unit is in the Home/Ready position.
Remove the bonnet by pressing both side latches and rotating it to about 45° before lifting it away.
If your unit has been used, clean the base and remove any litter or debris from the mounting pockets.
Remove the center plate from the bonnet by releasing the clips.
Reinstall the bonnet before attaching the LitterHopper.
Install the LitterHopper:
Verify the metal prong on the LitterHopper is clean and undamaged.
Align the LitterHopper posts with the circular mounting pockets on the back of the base.
Lower the LitterHopper into place.
Ensure the mounting tab is fully seated in the slot on the bonnet.
Check that there are no visible gaps between the LitterHopper, bonnet, or base.
The LCD screen will display "LitterHopper detected" when installation is successful.
Final setup:
Fill the globe to the MAX fill line and level the litter.
Fill the LitterHopper with fresh litter up to the MAX fill line and securely replace the lid.
Press the Cancel button to zero the weight sensors after adding litter.
Once detected, the LitterHopper is automatically enabled and ready to maintain your litter level.
Enable or disable LitterHopper:
From the control panel:
Press and hold the Cycle and Empty buttons for 3 seconds.
From the Whisker app:
Select your Litter-Robot 5 → Controls → LitterHopper → Enable or Disable.
Helpful Links:
LitterHopper Support Articles: litter-robot.com/support/article/litter-robot-5-litterhopper-installation-guide
Visit our Support Center: litter-robot.com/support
Warranty Information: litter-robot.com/explore/warranty.html
Follow Litter-Robot:
litter-robot.com
youtube.com/@LitterRobot



![A Closer Look at Internal Camera Recordings | Whisker App Update
You shared your feedback, and we listened.
Introducing Internal Camera Recordings: a simpler, more seamless way to see your cat’s entire bathroom visit, from start to finish, with fewer individual events cluttering your feed.
We’re also launching Bathroom Visit Summaries, bringing each visit’s recordings and key details together in one convenient place. Plus, new notifications let you know when your cat has visited, making it easy to see what happened with just a tap.
Whisker Product Manager, Nicole Liggins, walks through how the new features work and what you can expect based on your Whisker App plan.
Check out Internal Camera Recordings, only on the Whisker App: [Link]
Learn more about Internal Camera Recordings and Bathroom Visit Summaries on our blog: [LINK]
Meet Litter-Robot® 5 Pro, the most insightful automatic, self-cleaning litter box for cats.
Shop Litter-Robot® 5 Pro: https://www.whisker.com/litter-robot-5-pro
#LitterRobot #WhiskerApp #InternalCameraRecordings #BathroomSummaries #NewFeature #AppUpdate #BathroomVisits A Closer Look at Internal Camera Recordings | Whisker App Update](https://i.ytimg.com/vi/uVCEXfdx0tM/mqdefault.jpg)






