MATLAB | Learn to use FPGAs for Motor Control with Simulink @MATLAB | Uploaded October 2024 | Updated October 2024, 1 week ago.
FPGAs for Motor Control is becoming a pivotal technology in the development of high frequency switching power electronics and motor control systems, driven by highly mathematical computing algorithms. To implement such algorithms, engineers are increasingly looking towards System on Chip (SoC) devices, which blend the familiarity of embedded processors with the capabilities of FPGAs for parallel processing and deterministic behavior.
In this session you will learn how to use Simulink to deploy a field-oriented control (FOC) algorithm, onto an AMD-Xilinx Zynq UltraScale+ SoC device, with minimal need for deep FPGA programming knowledge. Using model-based design we will control a permanent magnet synchronous motor (PMSM), illustrate the process of automatically generating C and HDL code for the ARM Cortex processor and FPGA fabric within the SoC device. The techniques are demonstrated using the Trenz Electronics Motor Control Development kit.
Highlights:
- Model, Simulate, Test and Deploy the FOC algorithm onto Zynq UltraScale+ SoC Device.
- Explore the partition the design for ideal division of tasks between the ARM and FPGA.
- Automate deployment of the algorithm into reference frameworks for the processor and programmable logic.
Learn more about FPGA development: bit.ly/3IDqRgq
Chapters:
00:32 Learn how to use FPGAs for Motor control with Simulink
01:08 Overview of Model-Based Design for FPGAs
01:47 Motivation to use of FPGAs for motor control
03:20 Advantages of SoC Devices for control engineers
04:08 Model-Based Design Workflow
05:20 Simulink for Control Algorithms
05:50 Introduction to Motor Control Blockset
07:00 Introduction to the Trenz Electronic Motor Control Dev kit
08:05 Introduction to Field Oriented Control algorithm model
09:20 Introduction to HDL Coder
10:20 System Testbench in Simulink
11:05 Introduction to Hardware Support Package
11:50 Hardware-Software Partition
12:30 Generating C Code
13:02 Generating the HDL IP core
13:50 Reference design interface
14:50 Generating the HDL code
15:35 Introduction to Fixed-Point Conversion
16:15 Embedded system integration
17:00 Run the model on hardware
17:45 Key Takeaways
--------------------------------------------------------------------------------------------------------
Get a free product trial: goo.gl/ZHFb5u
Learn more about MATLAB: goo.gl/8QV7ZZ
Learn more about Simulink: goo.gl/nqnbLe
See what's new in MATLAB and Simulink: goo.gl/pgGtod
© 2024 The MathWorks, Inc. MATLAB and Simulink are registered trademarks of The MathWorks, Inc.
See mathworks.com/trademarks for a list of additional trademarks. Other product or brand names may be trademarks or registered trademarks of their respective holders.
FPGAs for Motor Control is becoming a pivotal technology in the development of high frequency switching power electronics and motor control systems, driven by highly mathematical computing algorithms. To implement such algorithms, engineers are increasingly looking towards System on Chip (SoC) devices, which blend the familiarity of embedded processors with the capabilities of FPGAs for parallel processing and deterministic behavior.
In this session you will learn how to use Simulink to deploy a field-oriented control (FOC) algorithm, onto an AMD-Xilinx Zynq UltraScale+ SoC device, with minimal need for deep FPGA programming knowledge. Using model-based design we will control a permanent magnet synchronous motor (PMSM), illustrate the process of automatically generating C and HDL code for the ARM Cortex processor and FPGA fabric within the SoC device. The techniques are demonstrated using the Trenz Electronics Motor Control Development kit.
Highlights:
- Model, Simulate, Test and Deploy the FOC algorithm onto Zynq UltraScale+ SoC Device.
- Explore the partition the design for ideal division of tasks between the ARM and FPGA.
- Automate deployment of the algorithm into reference frameworks for the processor and programmable logic.
Learn more about FPGA development: bit.ly/3IDqRgq
Chapters:
00:32 Learn how to use FPGAs for Motor control with Simulink
01:08 Overview of Model-Based Design for FPGAs
01:47 Motivation to use of FPGAs for motor control
03:20 Advantages of SoC Devices for control engineers
04:08 Model-Based Design Workflow
05:20 Simulink for Control Algorithms
05:50 Introduction to Motor Control Blockset
07:00 Introduction to the Trenz Electronic Motor Control Dev kit
08:05 Introduction to Field Oriented Control algorithm model
09:20 Introduction to HDL Coder
10:20 System Testbench in Simulink
11:05 Introduction to Hardware Support Package
11:50 Hardware-Software Partition
12:30 Generating C Code
13:02 Generating the HDL IP core
13:50 Reference design interface
14:50 Generating the HDL code
15:35 Introduction to Fixed-Point Conversion
16:15 Embedded system integration
17:00 Run the model on hardware
17:45 Key Takeaways
--------------------------------------------------------------------------------------------------------
Get a free product trial: goo.gl/ZHFb5u
Learn more about MATLAB: goo.gl/8QV7ZZ
Learn more about Simulink: goo.gl/nqnbLe
See what's new in MATLAB and Simulink: goo.gl/pgGtod
© 2024 The MathWorks, Inc. MATLAB and Simulink are registered trademarks of The MathWorks, Inc.
See mathworks.com/trademarks for a list of additional trademarks. Other product or brand names may be trademarks or registered trademarks of their respective holders.
