Uploaded October 2012 | Updated September 2026, 2 weeks ago
Just get your front wheels balanced to fix the shaking.
Lancer Fix Playlist bit.ly/2JQkmfC
---
🌐 Website darkdragonwing.com
---
0:00 Intro
0:21 Rotors
2:35 Struts
7:07 Axle
9:42 Inner Tie Rods
---
This is a blue 2003 Mitsubishi Lancer ES 2.0L 4G94 SOHC AUTO FWD.
---
ซ้อมรถสั่นตอนวิ่ง 100
The front side of the car car slipped off the jack stand and then the steering wheel started to be shaking or vibrating. Here are the things that I did to find the fix:
1. I changed front rotors เปลี่ยนจานดิสแบรค
2. I changed front struts เปลี่ยนโชคอัพ
3. I change right front axle เป็นเพลาขับ
4. I changed the inner tie rods เปลี่ยนลูกหมากด้านใน
About $200
For balancing, I use tape measure to measure the gaps between the front wheels. The gaps are at the front of the wheels, and the back of the wheels. I measure right on one of the lines on the surface of the tires and also on the inside cheeks of the tires. I drive around and come back to measure and see if the gaps are the same. Then I adjust the tie rod if they aren't. I would do this for like 10 times.. just to make sure.
It amazingly feels better after changing the inner tie rods. However, there is still a very little vibration during 60 mph. THE REAL CAUSE is the WHEELS AND TIRES. They are out of balance or warned out or too old.
---
For the sockets and stuff I would suggest you to buy the whole set. Same thing with the wrenches, get the set.
Only two special socket and one big wrench for them that you need to buy.
+19mm or 3/4" socket (1/2" drive)
+31.75 - 32mm or 1-1/4" Socket (1/2" drive)
+Big wrench (1/2" drive) 3:45 a "17-Inch Breaker Bar with a Flex Head".
The pipe, you can just walk in the store and try on like this 3:49
Other tools:
+5" C clamp
+Vise-Grip Curved Jaw Locking Pliers
+1 pair of 10"(or above) Coil Spring Compressor
+Inner Tie Rod Remover/Installer Tool
+a big(or small) metal(or brass) hammer
+zip-ties
---
Mods on this car:
*Red calipers, red drums
*Security alarm CrimeStopper SP-400 with the engine start system
*Trunk release kit
*GENUINE A/C heater air controller gears kit
---
⚠️ Disclosure: This section contains affiliate links to products. We may receive a commission for purchases made through these links.
Just get your front wheels balanced to fix the shaking.
Lancer Fix Playlist bit.ly/2JQkmfC
---
🌐 Website darkdragonwing.com
---
0:00 Intro
0:21 Rotors
2:35 Struts
7:07 Axle
9:42 Inner Tie Rods
---
This is a blue 2003 Mitsubishi Lancer ES 2.0L 4G94 SOHC AUTO FWD.
---
ซ้อมรถสั่นตอนวิ่ง 100
The front side of the car car slipped off the jack stand and then the steering wheel started to be shaking or vibrating. Here are the things that I did to find the fix:
1. I changed front rotors เปลี่ยนจานดิสแบรค
2. I changed front struts เปลี่ยนโชคอัพ
3. I change right front axle เป็นเพลาขับ
4. I changed the inner tie rods เปลี่ยนลูกหมากด้านใน
About $200
For balancing, I use tape measure to measure the gaps between the front wheels. The gaps are at the front of the wheels, and the back of the wheels. I measure right on one of the lines on the surface of the tires and also on the inside cheeks of the tires. I drive around and come back to measure and see if the gaps are the same. Then I adjust the tie rod if they aren't. I would do this for like 10 times.. just to make sure.
It amazingly feels better after changing the inner tie rods. However, there is still a very little vibration during 60 mph. THE REAL CAUSE is the WHEELS AND TIRES. They are out of balance or warned out or too old.
---
For the sockets and stuff I would suggest you to buy the whole set. Same thing with the wrenches, get the set.
Only two special socket and one big wrench for them that you need to buy.
+19mm or 3/4" socket (1/2" drive)
+31.75 - 32mm or 1-1/4" Socket (1/2" drive)
+Big wrench (1/2" drive) 3:45 a "17-Inch Breaker Bar with a Flex Head".
The pipe, you can just walk in the store and try on like this 3:49
Other tools:
+5" C clamp
+Vise-Grip Curved Jaw Locking Pliers
+1 pair of 10"(or above) Coil Spring Compressor
+Inner Tie Rod Remover/Installer Tool
+a big(or small) metal(or brass) hammer
+zip-ties
---
Mods on this car:
*Red calipers, red drums
*Security alarm CrimeStopper SP-400 with the engine start system
*Trunk release kit
*GENUINE A/C heater air controller gears kit
---
⚠️ Disclosure: This section contains affiliate links to products. We may receive a commission for purchases made through these links.
