KADA 2018D only Blue Screen Problem | Fix Any Dead SMD Station Using Universal STM32 @ilyasrao
KADA 2018D only Blue Screen Problem | Fix Any Dead SMD Station Using Universal STM32  @ilyasrao
Uploaded July 2026 | Updated November 2026, 6 days ago
introduction:
In this video, I demonstrate a permanent solution for the common "Dead Display" or "Logo Stuck" issue in the KADA 2018D+ SMD Rework Station. Since the original MCU is often unavailable or unreliable, we are replacing it with a powerful STM32 "Blue Pill" board running custom firmware.

What you will learn in this video:
. Identifying the 44-pin IC board and 19-pin LCD variant of the KADA 2018D+.
. Using an HT1621 display driver as a bridge between the STM32 and the original LCD.
. Step-by-step guide on flashing the STM32 using a USB-to-Serial (TTL) adapter.
. Complete wiring and jumper settings to integrate the new controller.
. Overview of the new features: Custom firmware, iron presets, and optimized sleep mode for longer heater life.

Tools Used:
. STM32F103C8T6 (Blue Pill)
. USB to Serial TTL Adapter
. HT1621 (extracted from a PWM frequency generator board)

Hardware Prep:
i removed the original MCU and bypassed certain points with jumpers to interface with the new STM32 board.

Firmware Installation:
Using official STM32 STM32CubeProgrammer software and a USB-to-Serial adapter, i flashed the custom binary file onto the STM32.

Wiring:
used 18 AWG copper wire to make the final connections between the STM32, the HT1621 bridge, and the station's motherboard, following a custom circuit diagram.

Feature Upgrades:
After the fix, i added that the machine now includes a preset feature for the soldering iron, allowing users to store and quickly jump to specific temperatures—a feature not present in the original setup.

This specific firmware is designed for the 44-pin MCU board version. Please verify your board model before applying this fix.

If you find this technical guide helpful, please Subscribe to CHAND MOBILES and hit the Like button. If you have a different rework station model that needs a custom firmware solution, let me know in the comments!

Resources & Downloads:
Get the circuit diagrams, pinout maps, and the binary firmware file here: [drive.google.com/file/d/17h3fhe15LaFEt1kmdIc4jjphlvEnOcIE/view?usp=drive_link]

Contact:
Whatsapp
03110171906
Facebook
web.facebook.com/raoilyas.chand
Gmail
chandmobiles22sp@gmail.com
#Kada2018D #ElectronicsRepair #STM32 #SMDRework #CustomFirmware #DIYElectronics #ChandMobiles #RepairGuide #STM32Project #SolderingRepair
KADA 2018D only Blue Screen Problem | Fix Any Dead SMD Station Using Universal STM32Custom Firmware for T12 Pro Soldering iron | T12 Soldering iron Upgrade STC15W408asSolar inverter card software | old ups converted into Sine wave inverter without battery #electronicNOKIA DISPLAY ON ARDUINO #ARDUINO #NOKIA #DISPLAY #1616 #TFTSMD hot Air Rework Station Repaired | WOLDER 8586D | electronic infoKUAIQU SPS-C3010 30V 10 Ampere dc Power Supply No Power repairing and tear downUMT SMART CARD PROBLEM #CM2 #EFTHOW TO MAKE A FAST CHARGING HUB STATION FAST CHARGERSugon 8620DX firmware ic replaced with Arduino | SMD Rework Custom Firmware #electronicNOKIA DISPLAY ON ARDUINO DETAILS EXAMPLES AND PINOUTS Urdu HindiDIY Universal SMPS Repair Module | Replace Black Magic Chip UC3843 | Bright Miracle Chip V2KADA 2018D+ OP ERROR SOLUTION
CHAND MOBILES |

KADA 2018D only Blue Screen Problem | Fix Any Dead SMD Station Using Universal STM32

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER