Uploaded February 2021 | Updated September 2026, 2 weeks ago
I will show you my attempt at modding the Jumper T-Lite to use an external Crossfire Nano module on 1W. The mod is really simple and you only need a resistor and an N channel MOSFET.
This mod allows the external module to be turned off when the radio is turned off or when the internal multi protocol module is used.
❗❗❗UPDATE - READ BEFORE MODDING ❗❗❗
It has been brought to my attention, that there are more efficient N channel MOSFET you should use. Instead of the one I used, go with one of the following:
► IRL540N: bit.ly/2OttUj0
► IRLB8743: bit.ly/37bi9Ek
They both have a lower Drain-Source resistance and are thus more efficient.
DISCLAIMER: I do not take responsibility for your actions. If you attempt this mod, you do it at your own risk. There is a chance of breaking the radio or shorting out the battery if you do something wrong. Be aware that 18650 batteries are not a joke and can be dangerous. Also by doing this you will probably use any support from Jumper and I am pretty confident void your warranty. Only do this if you know what you are doing.
►Used MOSFET (RFP12N10L): bit.ly/2N1yXqD
►SD-Card content: bit.ly/2MUdaRT
►TBS Agent Lite: bit.ly/3abQchM
💲 Buy the Jumper T-Lite on Banggood:
►banggood.com/custlink/GGDdI8rayc
🤯 Check out my homies:
►Noctaro Quad: goo.gl/8XWJUD
►kuhdjaku: goo.gl/WrqGop
►Resaikable FPV: goo.gl/wA1KY8
Tips:
►Paypal: paypal.me/stylesuxx
00:00 Intro
00:47 Needed tools
01:39 Step 1: Improving power wires
02:03 Step 2: Pulldown
02:14 Step 3: Routing the wires
02:44 Step 4: Hooking up the MOSFET
03:19 Step 5: Attaching the new power leads
03:57 Step 6: Putting everything back together
04:20 Powering on the radio with module
04:55 Preparing SD card
05:10 CRSF Setup
05:54 Power on time
06:24 Use quality cells
06:42 But how?
07:50 Outro
#Jumper #TLite #FPV
I will show you my attempt at modding the Jumper T-Lite to use an external Crossfire Nano module on 1W. The mod is really simple and you only need a resistor and an N channel MOSFET.
This mod allows the external module to be turned off when the radio is turned off or when the internal multi protocol module is used.
❗❗❗UPDATE - READ BEFORE MODDING ❗❗❗
It has been brought to my attention, that there are more efficient N channel MOSFET you should use. Instead of the one I used, go with one of the following:
► IRL540N: bit.ly/2OttUj0
► IRLB8743: bit.ly/37bi9Ek
They both have a lower Drain-Source resistance and are thus more efficient.
DISCLAIMER: I do not take responsibility for your actions. If you attempt this mod, you do it at your own risk. There is a chance of breaking the radio or shorting out the battery if you do something wrong. Be aware that 18650 batteries are not a joke and can be dangerous. Also by doing this you will probably use any support from Jumper and I am pretty confident void your warranty. Only do this if you know what you are doing.
►Used MOSFET (RFP12N10L): bit.ly/2N1yXqD
►SD-Card content: bit.ly/2MUdaRT
►TBS Agent Lite: bit.ly/3abQchM
💲 Buy the Jumper T-Lite on Banggood:
►banggood.com/custlink/GGDdI8rayc
🤯 Check out my homies:
►Noctaro Quad: goo.gl/8XWJUD
►kuhdjaku: goo.gl/WrqGop
►Resaikable FPV: goo.gl/wA1KY8
Tips:
►Paypal: paypal.me/stylesuxx
00:00 Intro
00:47 Needed tools
01:39 Step 1: Improving power wires
02:03 Step 2: Pulldown
02:14 Step 3: Routing the wires
02:44 Step 4: Hooking up the MOSFET
03:19 Step 5: Attaching the new power leads
03:57 Step 6: Putting everything back together
04:20 Powering on the radio with module
04:55 Preparing SD card
05:10 CRSF Setup
05:54 Power on time
06:24 Use quality cells
06:42 But how?
07:50 Outro
#Jumper #TLite #FPV
