RB26DETT rebuild, reinforcements and improvements. Nissan Skyline GT-R Inges garage 2016-10-06 | RB26DETT rebuild, overhaul, reinforcement and improvements. Nissan Skyline GT-R R32. 23.January to 30.April 2016.Jump to scene:1: Rods n pistons youtu.be/JQOej_pTtj4?t=422: Sylinder head youtu.be/JQOej_pTtj4?t=2353: Intake manifold n throttlebodys youtu.be/JQOej_pTtj4?t=2854: Turbos and exhaust manifolds youtu.be/JQOej_pTtj4?t=4565: Extra oil return from sylinder head to oilpan #1 youtu.be/JQOej_pTtj4?t=6136: Oil pan youtu.be/JQOej_pTtj4?t=6667: Timingbelt youtu.be/JQOej_pTtj4?t=8218: Extra oil return from sylinder head to oilpan #2 youtu.be/JQOej_pTtj4?t=12229: Flywheel n clutch youtu.be/JQOej_pTtj4?t=126710: Lifting engine into Skyline youtu.be/JQOej_pTtj4?t=134311: Pre-startup n startup youtu.be/JQOej_pTtj4?t=1492This is a short video edited down to 27 minutes. The engine was in good condition, but I wanted and improve the engine to withstand stress during race track and drag race. Engine block was drilled up to the new 86,5mm pistons and surface grounded. Cylinder heads were also surface grounded.Mounted Tomei 1,5mm oil restrictor to decrease the amount of oil to the cylinder head, which again leads to increased amount of oil in the oil sump. Made an extra oil return from the rear of the cylinder head, with a return hose below oil level in the sump, so that the oil flows faster down to the sump, and cannot be pumped up again (siphon principle).Mounted new Nismo main and rod bearings that are a little stronger than the original bearings. Oil clearings where all checked to 0,038mm. Thrust bearing clearance checked to less than 0,1mm, more than 0,05mm.New CP Carrillo 86,5mm forged lightweight pistons and Eagle forged H-beam rods with ARP 2000 rod bolts. Piston rings where filed to the correct gap, according to the sheet that came with the pistons: 1st ring 0,45mm , 2nd ring 0,55mm , oil rings 0,35-0,45mm.Re-used the Tomei Pon cams, 269 in and 252 ex, both with 8,9mm lift. Valve clearance where checked to 0,4mm in and 0,35 ex.Re-used the Nismo oil pump. I measured a total clearance to the crankshaft drive of 0,35mm (0,175mm on each side). Hope, and think, this is good enough for this power when keeping the rev limiter to max 8000rpm.New original NPT water pump. New ARP studs to keep the cylinder head and gasket tight.New Tomei metal head gasket with 1,5mm thickness (0,3mm over size) to keep the original compression ratio.New Tomei intake manifold metal gasket, throttle body metal gaskets and exhaust gaskets. New Nismo thermostat that opens at 62’C. It’s easier to keep it cold than cooling it down when it’s too hot ;-)Re-used the Greddy Grex oil cooler and oil cooler sandwich with thermostat.Re-used the HKS exhaust manifolds, but had to re-weld them because of cracks.Re-used the HKS 2530 ball bearing turbo’s.New Gates Racing timing belt, idler and tension wheel. Also see how I centred the CAS and CAS bracket in the "7: Timingbelt" -section. This is important. If not in centre, it could lead to bearing failure in the CAS or even crack.Filled oil in the oil pick-up to check the oil feed to the bearings, cylinder head and turbo’s.Oil pan where custom made to increase the oil amount about 1,7 litters, like “wings” on both sides. They do not go all the way down, to make the oil pick-up the lowest place in the sump. Also mounted Nismo baffle plates to keep the oil where the oil pick-up is, to prevent the oil pump sucking air which could lead to catastrophe.Re-used the OS Giken triple plate clutch and flywheel. New Nismo engine mounts. Re-used Greddy large intercooler and piping, Apexi Power FC ECU, Apexi boost control valve, Greddy / Denso 720cc injectors, 2 x 300ZX Z32 MAFS, Greddy air filters, ground wiring kit and Apexi exhaust system.If You have any questions, do not hesitate to ask.If You like the video, please press "LIKE" . Thanks :-DHere are my Skyline GTR at the racetrack:youtu.be/9WZmqA2o1y8 26.August 2016youtu.be/A1GQrkgGf28 24.July 2016Visit my YouTube channel at youtube.com/user/maxmekkker
Skyline GT-R Vaalerbanen Racetrack 15th August 2021 Inges garage 2021-10-02 | Skyline GT-R Vaalerbanen Racetrack 15th August 2021Finally, I have brought the whole family with me on the race track! Susanne and Theresa (daughters), Maria (wife) and Eivind (Theresa's boyfriend) each got their rounds in the GT-R.Thanks to everyone who subscribes to me. Very nice to see all of you who are interested.It's been too long since I last uploaded a video... sorry!Camera location also needs to be improved...For more information on the car, watch my other videos on my channel. Maybe especially the video where I overhal the engine.
Skyline GT-R at the drag strip Inges garage 2019-05-06 | Raceworz Norway at Gardermoen Raceway 4. may 2019.This was my first time at the drag strip with my Skyline GT-R.Not too happy with the result, but it's ok. Got serius tyre shake, so took softer starts after I set the best time at the 2nd run, 12,32 / 188 km/h (117 mph). I'm not quite sure how to get around the tyre shake. Feel free to add comments if you have any tips.Had a great day, and the Skyline works just fine! I've changed the ECU to a Maxxecu and tuned it. New video will come soon. I do now run with full boost at ~1,4 bar (~20 psi).Time slip:0.774 reaction1.882 60 feet5.237 330 feet144.76 km/h8.063 660 feet188.46 km/h12.321Feel free to like, share and comment.Visit my channel at: youtube.com/user/maxmekkker
Skyline GT-R vs Supra Inges garage 2018-08-28 | Supra and Skyline meeting at Gardermoen Raceway. Very unofficial drag race at the end of the drag strip. Everyone was running with street tires.The R32 was unbeatable this day :-DThis day I run with 1 bar (15psi) boost. The Apexi Power FC shows high signal from the knock sensors. I suspect engine knock, so decided to run at lower boost. I'll re-map it with new ECU, Maxxecu, next spring, April-May 2019, if goes as planned.Feel free to like, share and comment.Visit my channel at: youtube.com/user/maxmekkker
Skyline GT-R vs Tesla 90D Inges garage 2018-08-05 | Nissan Skyline GT-R R32 on low boost (0.6bar / 9psi) vs Tesla 90D.The Apexi Power FC showed high signal from the knock sensors. I suspect engine knock, so decided to run at low boost. I'll re-map it with new ECU, Maxxecu, next spring, April-May 2019, if goes as planned.The event was at Dagali Airport in Norway with 200SX-OGN. Without time records...just for fun and very unofficial .Feel free to like, share and comment.Visit my channel at: youtube.com/user/maxmekkker
Skyline GT-R: Upgraded cooling fans installation Inges garage 2017-10-01 | My old cooling fans started making bad sounds. The old fans did not have rubber pads between the fan fittings and the radiator, so the fans had vibrated slightly into the radiator cords.This video shows how I did when I replaced the fan for powerful fans.The old fans constantly pulled draw 7 amps each. The new ones constantly draw about 12 amps each (mounted on the radiator). They are both of pull type, which are more effective than push type.The old fans were already connected to Greddy MSS to control them. In the future, I will allow the ECU to do the job of managing them (fewer sources of error).Greddy larger radiator was also mounted on my GT-R when I bought it.Radiator Cooling Fan: Spal 12 "p. 30101504. Height 336mm (13.23"), width 321mm (12.64 "), thickness 63mm (2.48"). Max amps 25A.Oil cooler fan: Spal 5.2 "p.n. 30103011. Height 132mm (5.21"), width 132mm (5.12 "), thickness 60mm (2.36"). Max amps 10A.Live a comment if you have any questions, and I'll try to answer.
Skyline GT-R R32 wash n show off Inges garage 2017-09-10 | Just a wash n show off. Enjoy! Nissan Skyline GT-R R32, 1992. Showing the exterior and interior. Rocket Dancer carbon spoilers. Apexi exhaust system. A-Tech 18x9 rims with 245/35R18 Federal RSR tyres. Brembo V-Spec brakes. Nismo seat covers, Nismo floor mats, Nismo shift knob and Nismo mirror cover.Thanks for watching!Feel free to post a comment or question, like and subscribe.Visi my YouTube channel at youtube.com/user/maxmekkkerMy GT-R at the race track August 2016 youtu.be/9WZmqA2o1y8My GT-R at the race track July 2016 youtu.be/A1GQrkgGf28Engine rebuild January - April 2016 youtu.be/JQOej_pTtj4
Nissan Skyline GT-R R32 RB26DETT at the Race Track Inges garage 2016-08-27 | Nissan Skyline GT-R R32 RB26DETT at Rudskogen race track with NSK (Norsk Sportsvogn Klubb / Norwegian Sportscar Club), 26. August 2016. Chasing a Porsche GT3 CS and passing other cars.My brother, Jon Hildebrand, as passenger and co pilot.Thanks for watching!If you have any questions, just ask and I will try to answer as best I can.Visit my channel at youtube.com/user/maxmekkkerMotor was overhauled and reinforced from January to April 2016. See video here: youtu.be/JQOej_pTtj4Video from my first time with the Skyline GT-R at the same race track here: youtu.be/A1GQrkgGf28
Nissan Skyline GT-R R32 RB26DETT at the Race Track Inges garage 2016-07-25 | Nissan Skyline GT-R R32 RB26DETT at the Race Track with NSK (Norsk Sportsvogn klubb / Norwegian Sportscar club).This was my first day at the race track with my Nissan Skyline GT-R, 24. July 2016. It's an incredibly fun car to drive on the track!!! It was much more tail-happy than I had imagine, so have to learn to deal with it to get down lap times. Had initially problems with ignition knock because of the high temperature that day. Had to turn down the turbo pressure from 1,4 to 1,0 bar for it to be quiet, but then it was easier for me to drive, so it was a good thing.Running with Apexi Power FC without functions for ignition control by the intake temperature.Thanks for watching!If you have any questions, just ask and I will try to answer as best I can.Visit my channel at youtube.com/user/maxmekkkerMotor was overhauled and reinforced from January to April 2016. See video here: youtu.be/JQOej_pTtj4Also see video from the same race track when I'm chasing a Porsche 911 GT3 CS: youtu.be/9WZmqA2o1y8
Spitfire FPV with headtracker Inges garage 2015-10-03 | RC Spitfire FPV with headtracker.- Art-Tech Spitfire, wingspan: 88cm, length: 82cm, flying weight: just under 1kg - Top speed: 140km/h / 87mph.- Motor: NTM Prop Drive 28-36 2200KV / 696W with 6x4 propeller.- HobbyKing 70A BlueSeries Brushless Speed Controller- Battery: Turnigy nano-tech A-SPEC 2200mah 4S 65~130C Lipo.- Radio: TX: Spektrum DX7 2,4GHz. RX: Orange R800X DSMX- Fatshark Attitude googles.- Mobius camera.Flying over Smedstadgrenda, Gjerdrum, Akershus, Norway.See my other video of my Art-Tech Spitfire with nice sound here: youtu.be/FEAuNUOiz-w
Tiger Moth with acrobatics! Inges garage 2015-06-08 | I got this flight in a De Havillian Tiger Moth from my family as a birthday gift. From Kjeller airport, Akershus, Norway.This is a airplane build in 1941. It was used to train RAF pilots during world war 2.Engine: de Havilland Gipsy Major straight 4, 6.1 liters, 135hpTravel speed: 75-85 ktsMaxload: 828 kgWeigh: 506 kgFuel capasity: 86 litersFuel consumption: about 35 liters pr hour.
RC Falcon 56 with snow skis. Inges garage 2015-03-28 | This Falcon 56 RC airplane was bought in 1979. It was ready made in 1981. Today, 34 years later, took it its first flight, but now as a electric RC airplane.
FPV Bixler by night Inges garage 2015-01-24 | Flying my FPV RC Bixler 2 by night, five hours after sunset (21:00 pm).Almost cloudfree sky and landscape covered with snow.The picture in the googles are a little brighter.Camera: Sony 600TVL Super HAD with Low Illumination Lens.Skylark Dianmu OSD.Fatshark googles.Spektrum Tx.
Fast tuned-up Art-Tech Spitfire , nice sound! Inges garage 2015-01-03 | Art-Tech Spitfire with:- NTM Prop Drive 28-36 2200KV / 696W motor.- Turnigy nano-tech A-SPEC G2 2200mah 4S 14,8V 65~130C Lipo Pack.- HobbyKing 70A BlueSeries Brushless Speed Controller.- TGS Sport 6x4E Precision propeller- OrangeRx R800X DSMX Compatible 8Ch 2.4Ghz TwinPort Rx.
Bixler 2 FPV in Våler, over Glomma. Inges garage 2014-09-14 | Bixler 2 FPV. 14.10.2014.Tok en tur opp i lufta med Bixler'n mens Susanne, Theresa, Felix og jeg var på besøk hos Ingfrid.
Bixler 2 cloud surfing Inges garage 2014-09-14 | Bixler 2 cloud surfing, just when the fog lifts.HD Wing camera. Skylak Dianmu OSD. Fatshark Attitude video googles, 5.8Ghz 250mW video TX with circular polarized antenna. Spektrum DS7S TX.
Bixler 2 FPV chasing CUB Inges garage 2014-05-16 | Inge's Bixler 2 & Andre's CUB. The battle of Smedstadgrenda.
2nd flight with my selfmade I38 RC airplane Inges garage 2014-03-23 | After a few adjustments it flew fine.Specs:Wingspan: 125cmWeight: 1090g45A ESC
First flight with my selfmade i38 RC airplane CRASH! Inges garage 2014-03-22 | The first flight goes wrong!Specs:Wingspan: 125cmWeight: 1090g45 ESC
Bixler 2 FPV lowpass Inges garage 2014-01-01 | Recorded 23/11-2013 over Smedstadgrenda, Gjerdrum, Akershus, Norway.Bixler 2 from Hobbyking. Fatshark FPV system with Sony camera. Spektrum Tx, Orange Rx with satellite reciver. Recorded with HD Wing Camera.
Bixler 2 flying over Lillestrøm, Norway FPV Inges garage 2013-09-06 | Inge's Bixler 2 flying over Lillestrøm, Norway, 27.08.2013Info:Wingspan 1500mm.Flying weight: 800g.Spektrum DX7s Tx radio transmitter.OrangeRx R620 full range radio receiver w/failsafe.HD Wing Camera 1280x720.
Skogen Performance, Patricks BMW E30 Tech2 S50B32 Inges garage 2013-07-06 | Skogen Performance, Patrick's BMW E30 Tech2 S50B32. 200SX OGN treff på Rudskogen 6.Juli 2013.Lagt ut for Skogen Performance.
RC Bixler 2 under the volleyball net, first attempt goes very wrong! Inges garage 2013-06-30 | Inge's Bixler 2 and Andre's CUB goes under the volleyballnet. First attempt goes very wrong! The 2 next attempts goes fine.FPV. Camera mounted on the Bixler 2.Smedstadgrenda, Gjerdrum, Akershus, Norway, 23.June 2013.
Tørris og vann i cola-flaske Inges garage 2013-03-27 | Når tørr is smelter, går den ikke over til vann, men gass. Gassen får ikke plass i flaska :oDFilmet i Smedstadgrenda, Gjerdrum, Akershus, Norway.
Leke med tørris Inges garage 2013-03-25 | Theresa leker med tørris, lager en røykboble / røykbombe med tørris, vann og såpeboblevann.Slik gjør du det:- Fyll en bolle med vann.- Ta noen skjeer med tørris i vannet.- Ta en lodden tråd og dypp den i såpe boble vann.- Trekk tråden over skålen og "fang" røyken fra tørrisen som koker i vannet.- Se boblen vokse til en stor boble som til slutt sprekker.- Ha det moro! Men husk at man kan skade seg på tørrisen hvis man får den på huden, siden det er veldig kald.
RC Piper J3 CUB FPV over low clouds i sunrise Inges garage 2013-03-10 | Flying over Smedstadgrenda, Gjerdrum, Norway.Camera mounted under the belly.
RC Tamiya Sand Scorcher Inges garage 2012-12-08 | Restored RC Tamiya Sand Scorcher.I have changed the battery to a 7,4V 2200mAh 40-50C Li-Po battery (original 7,2V 1200mAh Ni-Cd), both servos to digital with metal gears, radio Rx and TX. The original battery box with 4 AA-batteries have bin changed to a 5A BEC.The rest is original, inc. the motor and speedcontroller.This car was a birthday gift to me from my grandmother, grandfather and uncle on my 9 years birthday 1983. Now, 29 years later, I found the same car in a museum! I decided to restore my old RC car, and here it is! :oD
RC Piper J3 CUB FPV, in sunset, landscape covered in snow. Inges garage 2011-12-12 | RC Piper J3 CUB EPO airplane with FPV onboard camera. Flying over Smedstadgrenda, Gjerdrum, Norway 7.December 2011. Camera mounted on top of the right wing.
RC Airplane Piper J3 CUB in sunrise FPV Inges garage 2011-10-21 | RC Piper J3 CUB in sunrise in the air over Smedstadgrenda, Gjerdrum, Akershus, Norway. Between 3:43 and 3:55 you can see four swans below.
RC Piper J3 CUB Epo FPV Inges garage 2011-10-20 | Up in the clouds and strokes the grass. Flying over Smedstadgrenda, Gjerdrum, Akershus, Norway.
Nissan 200SX S13, SS2 Gardermoen 1.August 2010 Inges garage 2010-08-01 | Nissan 200SX S13 CA18DET, SS2.
200SX Trackday Rudskogen 8.Mai 2010 Inges garage 2010-05-09 | 200SX S13 CA18DET på Trackday, Rudskogen 8.Mai 2010.
Nissan 200SX S13 CA18DET Inges garage 2009-11-26 | Nissan 200SX S13 CA18DET at the Dynopack, braking 343hp / 424nm @ 1,4bar at the crank.Greddy E-Manage piggy-back.
Japsetreff 21.Mai 2009 Inges garage 2009-06-02 | Japsetreff med 200SX OGN på Vålerbanen 21.Mai2009. Maxmekker's 200SX S13 CA18DET
Maxima vs Golf VR6 Inges garage 2009-02-12 | Maxima vs Golf VR6, Dragrace at Gardermoen, "En Dag På Strippen" with Bilsport 2003.Got the 2nd place in the class "fwd with natural aspiration". Best time: 60 feet: 2,2261/8 mile: 9,645 @ 116,38 kph1/4 mile: 14,978 @ 148,76 kph
