Uploaded August 2018 | Updated November 2026, 13 hours ago
Welcome Back,
Sorry for the Lack of Uploads, but due to health reasons i have not been able to get into the Shedquarters.
This week I wanted to make something special for my Nephew, as he is a Jack Daniels fan, i decided to upcycle an old Cutlery Display Case into a fitting home for a bottle of Jack Daniels, I offer you a Jack Daniels Presentation case.
I started by removing all the hardware, it soon became apparent that the case was in worse condition than first thought.
There was a strip of wood missing from the lower part on the right hand side that needed replacing. I trimmed a length of scrap wood to fit including the mitres on each end. The type of wood was not important, due to the fact that i was going to paint it later. Once the glue had dried, i shaved of any protrusions, using my Stanley Block Plane.
The lid had one side that had also came loose, so using Gorilla glue, i fixed it back in place, using masking tape as a clamp, until the glue dried.
The veneer on the lid was water damaged and peeling off, to remove this i set to work with a stanley blade and a sharp paint scraper, once removed a quick sanding provided a smooth surface to start to add some embellishments
I had printed out a template of the iconic Jack Daniels sign and started cutting, as i wanted to add a twist.
The newly trimmed template was adhered to the lid with some spray adhesive, once cured i started with the routering. I used a 2 mm up-cutting router bit, taking slow and steady passes. I avoided forcing the cut as with the bit, being so small, there was a lot of potential for snapping.
There was very little clean up needed after the routering was completed, so i started to apply a spray primer, my current favorite is the one from the Wilko’s Range (UK only), once dry i went over with a coat of matt black spray.
Now came the time consuming part, i have no real experience in detail painting, but as always i like to to push myself. With the finest brush in my toolbox, i set to work infilling the recently routered signage with gloss paint.
I hope you enjoy the video.
If you would like to Support my work, then please consider leaving me a “tip” in my paypal account - all donations will go towards future projects
paypal.me/mgmakes
Please Follow me on,
Instagram
instagram.com/mgmakes
Facebook
facebook.com/mg.makes.73
Find Me on Etsy
etsy.com/uk/shop/MGmakes1973
A Proud Member of
Small Workshop YouTube Makers Facebook Group
facebook.com/groups/SmallWorkshopYouTubeMakers
Makers Media Network
facebook.com/groups/MakersMediaNetwork
Welcome Back,
Sorry for the Lack of Uploads, but due to health reasons i have not been able to get into the Shedquarters.
This week I wanted to make something special for my Nephew, as he is a Jack Daniels fan, i decided to upcycle an old Cutlery Display Case into a fitting home for a bottle of Jack Daniels, I offer you a Jack Daniels Presentation case.
I started by removing all the hardware, it soon became apparent that the case was in worse condition than first thought.
There was a strip of wood missing from the lower part on the right hand side that needed replacing. I trimmed a length of scrap wood to fit including the mitres on each end. The type of wood was not important, due to the fact that i was going to paint it later. Once the glue had dried, i shaved of any protrusions, using my Stanley Block Plane.
The lid had one side that had also came loose, so using Gorilla glue, i fixed it back in place, using masking tape as a clamp, until the glue dried.
The veneer on the lid was water damaged and peeling off, to remove this i set to work with a stanley blade and a sharp paint scraper, once removed a quick sanding provided a smooth surface to start to add some embellishments
I had printed out a template of the iconic Jack Daniels sign and started cutting, as i wanted to add a twist.
The newly trimmed template was adhered to the lid with some spray adhesive, once cured i started with the routering. I used a 2 mm up-cutting router bit, taking slow and steady passes. I avoided forcing the cut as with the bit, being so small, there was a lot of potential for snapping.
There was very little clean up needed after the routering was completed, so i started to apply a spray primer, my current favorite is the one from the Wilko’s Range (UK only), once dry i went over with a coat of matt black spray.
Now came the time consuming part, i have no real experience in detail painting, but as always i like to to push myself. With the finest brush in my toolbox, i set to work infilling the recently routered signage with gloss paint.
I hope you enjoy the video.
If you would like to Support my work, then please consider leaving me a “tip” in my paypal account - all donations will go towards future projects
paypal.me/mgmakes
Please Follow me on,
instagram.com/mgmakes
facebook.com/mg.makes.73
Find Me on Etsy
etsy.com/uk/shop/MGmakes1973
A Proud Member of
Small Workshop YouTube Makers Facebook Group
facebook.com/groups/SmallWorkshopYouTubeMakers
Makers Media Network
facebook.com/groups/MakersMediaNetwork










