Uploaded October 2026 | Updated November 2026, 2 days ago
Uncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST: fpvknowitall.com/ultimate-fpv-shopping-list
SUPPORT ME ON PATREON at: bit.ly/2Ep5Sia
THIS IS MY FULL TIME JOB. Here are other ways that you can support me: fpvknowitall.com/support-me
---
I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.
The exact 21700 cells I used: 18650batterystore.com/products/samsung-58e-21700-battery
0.1mm nickel strip - https://link.amazon/B09OkpMqV
21700 Fish Paper Rings - https://link.amazon/B0fiDX5NX
Adhesive-backed fish paper - https://link.amazon/B037IBFmt
4S balance leads - https://link.amazon/B0dIsIAgH
Silicone wire - https://link.amazon/B076UoPpK
65W USB-C power board - https://link.amazon/B02MiLJL1
MANDATORY DISCLAIMER: I am a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites.
---
0:00 - You can build this battery pack!
0:53 - YOU WANT THIS. Don't you?
2:04 - Caveats
2:35 - Stuff you need
8:03 - 3D print the case
Print your own battery case from:
thingiverse.com/thing:7423769
9:10 - Apply the fish paper
11:14 - Arrange the batteries in 4S1P configuration
12:11 - Cut lengths of nickel strip
13:13 - Solder to the strips first? Or after?
14:22 - Be careful from here!
15:12 - Spot-welding the strips
Learn more about my kWeld spot welder at:
youtube.com/watch?v=9Zc5GL7IVL4
15:54 - No really BE CAREFUL
16:46 - Install the positive and negative strips
17:36 - Solder the wires
23:13 - Slide the cells into the case
24:55 - I have doubts
26:11 - Adjust the wire lengths
26:31 - Install the USB power board
28:10 - Test the wiring
29:06 - Close up the case
31:00 - Install the XT60
32:07 - You're done!
Uncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST: fpvknowitall.com/ultimate-fpv-shopping-list
SUPPORT ME ON PATREON at: bit.ly/2Ep5Sia
THIS IS MY FULL TIME JOB. Here are other ways that you can support me: fpvknowitall.com/support-me
---
I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.
The exact 21700 cells I used: 18650batterystore.com/products/samsung-58e-21700-battery
0.1mm nickel strip - https://link.amazon/B09OkpMqV
21700 Fish Paper Rings - https://link.amazon/B0fiDX5NX
Adhesive-backed fish paper - https://link.amazon/B037IBFmt
4S balance leads - https://link.amazon/B0dIsIAgH
Silicone wire - https://link.amazon/B076UoPpK
65W USB-C power board - https://link.amazon/B02MiLJL1
MANDATORY DISCLAIMER: I am a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites.
---
0:00 - You can build this battery pack!
0:53 - YOU WANT THIS. Don't you?
2:04 - Caveats
2:35 - Stuff you need
8:03 - 3D print the case
Print your own battery case from:
thingiverse.com/thing:7423769
9:10 - Apply the fish paper
11:14 - Arrange the batteries in 4S1P configuration
12:11 - Cut lengths of nickel strip
13:13 - Solder to the strips first? Or after?
14:22 - Be careful from here!
15:12 - Spot-welding the strips
Learn more about my kWeld spot welder at:
youtube.com/watch?v=9Zc5GL7IVL4
15:54 - No really BE CAREFUL
16:46 - Install the positive and negative strips
17:36 - Solder the wires
23:13 - Slide the cells into the case
24:55 - I have doubts
26:11 - Adjust the wire lengths
26:31 - Install the USB power board
28:10 - Test the wiring
29:06 - Close up the case
31:00 - Install the XT60
32:07 - You're done!










