Is xTool P3 IR Enough for Metal? Or Do You Need Fiber? @3DPrintscape
Is xTool P3 IR Enough for Metal? Or Do You Need Fiber?  @3DPrintscape
Uploaded September 2026 | Updated November 2026, 2 days ago
Is the xTool P3 5W IR laser enough for metal — or do you still need a fiber laser? CO2 vs IR on business cards, stainless cards, brass and steel coins, with real settings and an honest verdict.

I ran side-by-side tests on the P3: coated business cards and brushed stainless with CO2 vs IR, then IR-only on brass and stainless coins (no CO2 on reflective coins — lens risk). Full power/speed/LPI and times on screen.

━━━━━━━━━━━━━━━━━━━━━━
🧰 xTool
━━━━━━━━━━━━━━━━━━━━━━
▸xTool P3: xtool.pxf.io/aNZE5N
▸xTool P2S: xtool.pxf.io/WOPV4J
▸xTool P3 5w IR: xtool.pxf.io/5kGvY2

━━━━━━━━━━━━━━━━━━━━━━
🖨️ MY GEAR & RECOMMENDED PRODUCTS
━━━━━━━━━━━━━━━━━━━━━━
▸ SparkX i7: crealityofficialstore.sjv.io/c/5142166/3791607/25652
▸ SparkX i7 on Amazon: geni.us/IDV6JKl
▸ All Creality printers: crealityofficialstore.sjv.io/c/5142166/2096381/25652
▸ Flashforge Creator 5: flashforge.sjv.io/YVj0Jq
▸ Flashforge Creator 5 Pro: flashforge.sjv.io/5kq9v3
▸ Anycubic Kobra 4: us.anycubic3d.com/products/kobra-4-combo-3d-printer?_sasdk=dMTlmYTM3YWIwYmExNjdhLTBkMWVkNTE2Njc4NjEzLTRjNjU3YjU4LTQ5MTYxNjAtMTlmYTM3YWIwYmIyNjA2&ref=3dprintscape&utm_source=goaffpro
▸ BIQU filament: tidd.ly/4ukNtsZ
▸ Filament on Amazon: geni.us/BJx0Gdj

─────────────────────────────
📌 CHAPTERS
─────────────────────────────
0:00 Intro – IR good enough or need fiber?
0:59 Business card: CO2 vs IR + settings
2:14 Stainless steel cards: CO2 vs IR
4:30 Brass & stainless coins on IR
6:26 Verdict: marking vs deep engraving
7:49 Cost, 2–3W vs 5W, who should buy

─────────────────────────
📌 CONNECT
─────────────────────────
💬 Discord: discord.gg/Bu94EYVkrU
🌐 Website: 3dprintscape.com
📸 Patreon: patreon.com/3dprintscape

If this helped, hit like and subscribe — and tell me if you want copper/titanium next or a P3 IR vs fiber head-to-head.

#xtoolp3 #irlaser #laserengraving #metalengraving #xtool #co2laser
Is xTool P3 IR Enough for Metal? Or Do You Need Fiber?These 3D Prints Started as AI Renders — Full PipelineFlashforge Creator 5 Pro After 1 Week: The Real Deal?Pronterface Setup – The Easy Way!The Cheapest Way to Setup a 3D PrinterHi3D Full Workflow: Text to 3D Printable Model (4 Prints)Is the Revopoint POP 4 Worth It? Unboxing & Real-World Scan TestsI Tested The Elegoo Centauri Carbon 2 For 100+ Hours — Heres What BrokeFIXDRY Filament Dryer Box – Initial ReviewAdd Percent Complete to Marlin FirmwareThis Firmware Builder Saves Hours of HeadachesFix Your 3D Prints With This One Simple Trick #3dprinting #hacks
3D Printscape |

Is xTool P3 IR Enough for Metal? Or Do You Need Fiber?

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER