Uploaded November 2024 | Updated September 2026, 3 weeks ago
iRobot Roomba Combo Robot Vacuum & Mop (Y0110)
B0CNKVHSS9
SETUP:
Upon receiving, the robot came with full battery, I didn't need to charge it before use, but do require to sat on the base for app setup. Since I'm already a iRobot App user for my 6 series, setting up the Y0110 was fairly easy, basically just add a device, pressing couple button and let it sync, then it's ready to go.
RUNNING AND MAPPING:
This model starts with a straight line to the end of the wall, then make a perfect U-turn, make another straight line right back. it does cover every inch when it's in an open area. I really like that, compare to Y0110, my 6 series is like in a dumb/blind mode, it will make a angle turn whenever it hits the wall or object, therefore it's always zig zagging. Y0110 seem like knowing what direction it's going, even when it his object, it will slowly adjust itself to go back to it's original direction to make straight line. and at the end of each job, you will receive a map in the app, telling you the area it covered. But the map can be confusing sometime, maybe because I do pick up the robot and let it run at certain area one more round as needed, this might mess up the mapping.
CLEANESS:
I think the end result of mopping is good enough. There are always some tough stains here and there, I just need to give it a handwipe if I want it to be perfect, but I don't blame the robot. I tried mopping with water only, and with iRobot hardwood floor cleaning solution. Both options looks the same to me, but I personally prefer to use cleaning solution, just to hope it will sanitize better. Cleaning solution does make the house smells cleaner =P
The vacuum part, It does the job as it's expected. I use this robot mainly for kitchen and living room. I have a dog and a kid in the household. So I do need it to pick up small crumbs before it mops over it. and so far, the concept works out perfectly.
iRobot Roomba Combo Robot Vacuum & Mop (Y0110)
B0CNKVHSS9
SETUP:
Upon receiving, the robot came with full battery, I didn't need to charge it before use, but do require to sat on the base for app setup. Since I'm already a iRobot App user for my 6 series, setting up the Y0110 was fairly easy, basically just add a device, pressing couple button and let it sync, then it's ready to go.
RUNNING AND MAPPING:
This model starts with a straight line to the end of the wall, then make a perfect U-turn, make another straight line right back. it does cover every inch when it's in an open area. I really like that, compare to Y0110, my 6 series is like in a dumb/blind mode, it will make a angle turn whenever it hits the wall or object, therefore it's always zig zagging. Y0110 seem like knowing what direction it's going, even when it his object, it will slowly adjust itself to go back to it's original direction to make straight line. and at the end of each job, you will receive a map in the app, telling you the area it covered. But the map can be confusing sometime, maybe because I do pick up the robot and let it run at certain area one more round as needed, this might mess up the mapping.
CLEANESS:
I think the end result of mopping is good enough. There are always some tough stains here and there, I just need to give it a handwipe if I want it to be perfect, but I don't blame the robot. I tried mopping with water only, and with iRobot hardwood floor cleaning solution. Both options looks the same to me, but I personally prefer to use cleaning solution, just to hope it will sanitize better. Cleaning solution does make the house smells cleaner =P
The vacuum part, It does the job as it's expected. I use this robot mainly for kitchen and living room. I have a dog and a kid in the household. So I do need it to pick up small crumbs before it mops over it. and so far, the concept works out perfectly.
