Uploaded September 2020 | Updated September 2026, 1 week ago
$2 for 2-Layer PCBs & $5 for 4-Layer PCBs: jlcpcb.com
More project information(Code,Schematic,etc):- nematicslab.com/diy-iot-weather-station-arduino-blynk
To add esp8266 boards in Arduino IDE software: nematicslab.com/install-esp8266-esp32-boards-on-arduino-ide
Website,
NematicsLab.com
Patreon,
patreon.com/NematicsLab
For Sponsorships or Endorsements ONLY!
Business@Nematicslab.com
For project-related questions use Facebook or Twitter @NematicsLab
Music used in the video:
1) Manhattan by Dyalla
2) Midnight Prophet by Sarah, The Illstrumentalist
---------- Affiliate ----------
Gearbest- bit.ly/2KD54KD
Banggod- bit.ly/2xgJIK5
LCSC - bit.ly/2KD0hJ0
---------- Social Media ----------
Facebook - bit.ly/2FC5lJz
Instagram - bit.ly/2XddQpe
Twitter - bit.ly/2IUhqMm
--------------------Electronics Starter kit Tools--------------------
Soldering Iron - banggood.in/custlink/DKGKUAqCKa
Solder wire - banggood.in/custlink/mv3vks2ROf
Helping Hands - banggood.in/custlink/vmvmMAqd0C
Hot Glue - banggood.in/custlink/D3GDMAkWDS
----------------Little information about Video-------------------
This project is related to initial steps in IoT world, here we will interface DHT11/DHT22 sensor with NodeMCU or other ESP8266 based board and receive data on internet we are going to use Blynk application, use the following tutorial link if you are not familiar with blynk application.
For Blynk (it require only few minutes): docs.blynk.cc
After this you are require to add esp8266 boards in your Arduino IDE software, use following link
There are simple hardware connections, you are not going to deal with any messy connections, so recreate & enjoy this project.
$2 for 2-Layer PCBs & $5 for 4-Layer PCBs: jlcpcb.com
More project information(Code,Schematic,etc):- nematicslab.com/diy-iot-weather-station-arduino-blynk
To add esp8266 boards in Arduino IDE software: nematicslab.com/install-esp8266-esp32-boards-on-arduino-ide
Website,
NematicsLab.com
Patreon,
patreon.com/NematicsLab
For Sponsorships or Endorsements ONLY!
Business@Nematicslab.com
For project-related questions use Facebook or Twitter @NematicsLab
Music used in the video:
1) Manhattan by Dyalla
2) Midnight Prophet by Sarah, The Illstrumentalist
---------- Affiliate ----------
Gearbest- bit.ly/2KD54KD
Banggod- bit.ly/2xgJIK5
LCSC - bit.ly/2KD0hJ0
---------- Social Media ----------
Facebook - bit.ly/2FC5lJz
Instagram - bit.ly/2XddQpe
Twitter - bit.ly/2IUhqMm
--------------------Electronics Starter kit Tools--------------------
Soldering Iron - banggood.in/custlink/DKGKUAqCKa
Solder wire - banggood.in/custlink/mv3vks2ROf
Helping Hands - banggood.in/custlink/vmvmMAqd0C
Hot Glue - banggood.in/custlink/D3GDMAkWDS
----------------Little information about Video-------------------
This project is related to initial steps in IoT world, here we will interface DHT11/DHT22 sensor with NodeMCU or other ESP8266 based board and receive data on internet we are going to use Blynk application, use the following tutorial link if you are not familiar with blynk application.
For Blynk (it require only few minutes): docs.blynk.cc
After this you are require to add esp8266 boards in your Arduino IDE software, use following link
There are simple hardware connections, you are not going to deal with any messy connections, so recreate & enjoy this project.
