Installing 5 VELUX Skylights in a Row Using Combi Flashing @veluxusa
Installing 5 VELUX Skylights in a Row Using Combi Flashing  @veluxusa
Uploaded August 2023 | Updated November 2026, 6 hours ago
This skylight installation video demonstrates how to install 5 deck-mounted skylights in a row using VELUX combi flashing. Learn more about all the VELUX flashing kits pro.veluxusa.com/products/flashing-systems

Here is another tutorial on installing a VELUX Sun Tunnel skylight youtu.be/1jGfbbstZCA

=========================================
This video is NOT sponsored.
============================

Connect with a VELUX Representative or Find a Skylight Installer
============================
VELUX Representative Consultation: veluxusa.com/design-advice
Find a Skylight Installer: veluxusa.com/locator

============================
Connect With Us!
============================
Facebook: facebook.com/VELUXAmerica
Instagram: instagram.com/veluxusa
Pinterest: pinterest.com/veluxamerica
or
Facebook for Pros: facebook.com/veluxusapro
Instagram for Pros: instagram.com/veluxusapro

Question? – Have a question about installing multiple skylights using VELUX EKL or EKW combi-flashing? Leave it in the comments!

⏰Time codes⏰
0:00 Installing multiple skylights with combi-flashing
0:10 Distance measurements for VELUX combi-flashing
0:21 Interior room and attic preparation
0:31 Marking the skylight placement on the ceiling
0:47 Installing framing for skylights and adjusting truss width
1:01 Furring out the trusses for equal distance
1:17 Exterior preparation for multiple skylights in a row
1:27 Marking and cutting skylight openings in roof
1:42 Remove shingles around skylight openings
1:52 Step 3 Skylight Installation
2:10 Using a 2X4 to keep skylights aligned
2:22 Wooden spacer blocks between skylights
2:46 Step 4 Installing adhesive underlayment
3:44 Install shingles at base of skylights
3:55 Installing the bottom sill flashing
4:10 Connecting sill flashing with slide strip
4:21 Installing VELUX engineered step flashing
5:04 Installing the VELUX engineered gutters
5:54 Reinstall cladding and Install head flashing
6:22 Step 5 Enjoy new skylights

#velux #skylights #skylightinstallation #VELUXUSA

About: The installation of a series of skylights using combi flashing begins by marking off the opening in the interior. First, remove any insulation above the area, and then cut out the drywall. Install a header and adjust the trusses as necessary to ensure equal distance between skylights. On the roof, mark the area of the roof to be removed and cut the openings with a saw. Remove all shingles around the openings. Then, install skylights using ring shank nails provided. Next, attach the adhesive underlayment on all four sides. Attach the lower sills and then use the side strips to connect the lower sills. Next, install the engineered step flashing. After that, install the gutters between the skylights makings sure to get the edges under the lower sill flashing. Finally, install the cladding and the head flashing. Install the remainder of the shingles, leaving room for water and debris to flow.
Installing 5 VELUX Skylights in a Row Using Combi FlashingUsing Skylights to Create Passive VentilationVELUX Sun Tunnel Flexi Loc VideoHow to Pair a VELUX 300 Remote to a Skylight ShadeHow to darken a bedroom that has skylightsTips for Connecting the Upper and Lower Section of Tube During a Sun Tunnel Installation #veluxVELUX Sustainability Strategy 2030Using skylights to transform home reno to-dos into ta-da momentsVELUX Flat Ceiling AnimationHow To Copy a VELUX KLI110 skylight remote to Another KLI110Skylights Create the Perfect Kitchen Light for a Food Photographer #velux #kitchendesign #skylightsHow to Remove a VELUX Skylight Shade That Was Added to a Skylight
VELUX USA |

Installing 5 VELUX Skylights in a Row Using Combi Flashing

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER