Ice Climbing: 13. Placing Ice Screws | Climbing Tech Tips @ClimbingTechTips
Ice Climbing: 13. Placing Ice Screws | Climbing Tech Tips  @ClimbingTechTips
Uploaded February 2018 | Updated November 2026, 11 hours ago
Subscribe to our channel for the latest training videos, climbing tutorials and more! In this video we look at how to place ice screws. Ice screws offer protection for the lead climber in the event of a fall, the same way cams and stoppers do in rock climbing. Below are the steps for placing ice screws:

Step 1: Turn one foot sideways if possible to help create a more comfortable stance while placing the screw.

Step 2: Place the screw at waist level. This position allows the climber to maximize power without compromising balance. Placing a screw in a higher position minimizes power and affects balance.

Step 3: Begin by pushing and twisting the screw into the ice until the teeth bite and hold the screw in place. Note that the angle should be slightly lower than perpendicular, as this is the strongest and most effective angle to place a screw (the strength actually comes from the threads pulling against the ice).

Step 4: Pop out the “turbo” or crank, and continue screwing the piece into the ice. Be sure to return the crank to the original position, as the rope can potentially catch on this in a fall. These cranks, such as the “turbo” on the Black Diamond screw, have been rumored to sever ropes. You must return the crank to the original position!

Step 5: Chip away any weaker surface ice around the screw that may have cracked during the placement, and set the screw so the hanger is flush with the ice and hanging downward.

Please note that best practice / pull tests show we should back off the screw a bit, rather than over-crank it to get the hanger to sit flush on the ice. You can damage the thread placements by cranking the screw with too much force. This means if the hanger sits flush with the ice but is in the upward direction, it is best to un-thread a half turn to get the hanger to hang down, instead of cranking it tighter.

Step 6: Once the screw is screwed in up to the hanger, clip a quickdraw to the hanger. Then clip your rope into the lower carabiner of the quickdraw, just like sport climbing. Be sure to avoid back-clipping the rope. For more on this see our video on “Avoid Back-Clipping” [hyperlink to video].

Below are a few additional considerations when placing screws:

- More often than not, the leader will need to place the screw with one hand, especially on steeper ice. This makes the first step, which is getting the teeth to bite, the trickiest, and the most likely time you could drop a screw. No dropping!

- Strength of the screw placement depends on the quality of the ice you place it in:

Good = Cold, Clear, Dry

Bad = Soft, Warm, Wet


We hope you found this video helpful.

Please remember, ice climbing is inherently dangerous. Climb at your own risk. Visit ClimbingTechTips.com for related comments, additional videos, and community feedback!
Ice Climbing: 13. Placing Ice Screws | Climbing Tech TipsIce Climbing: 15. Sharpening Crampons and Ice Tools | Climbing Tech TipsAlpine & Mountaineering: 27. The Kiwi Coil | Climbing Tech TipsMulti-Pitch Trad: 4. Gear Logistics | Climbing Tech TipsAlpine & Mountaineering: 24. Knot Considerations | Climbing Tech TipsMulti-Pitch Trad: 13. Route Logistics | Climbing Tech TipsTraditional Climbing: 19. Maximizing Space at the Anchor | Climbing Tech TipsAid Climbing & Big Walls: 11. Racking for Aid Lead - Part 1 of 2 | Climbing Tech TipsFitness for Climbing: 5. Hangboard - Repeaters | Climbing Tech TipsAid Climbing & Big Walls: 19. Offset Placements - Offset Nuts | Climbing Tech TipsAlpine: 19. Clothing Considerations | Climbing Tech TipsGym Top Rope Climbing: 4. Belay Device Fundamentals | Climbing Tech Tips
Climbing Tech Tips |

Ice Climbing: 13. Placing Ice Screws | Climbing Tech Tips

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER