Uploaded June 2023 | Updated November 2026, 22 hours ago
The IBM PCjr. used an Intel 8088 CPU running at 4.77MHz, like the IBM PC and IBM PC/XT that came before it. When running with 64-128KiB of RAM, its memory performance is severely compromised relative to a PC or XT because the PCjr. must share that memory with its video display hardware whereas on a PC or XT the video memory is separate from the system memory. When running programs above the 128KiB range, its performance is about equal to an PC or XT. Most IBM PCjrs used socketed CPUs, so their 8088s could be upgraded to NEC V20s for a 10-25% performance increase, depending on the application. A soldered CPU can be desoldered and replaced with a socket for the upgrade. That V20 will still be running at 4.77MHz if nothing else is done with the system.
There is a single clock source in a PC, XT or PCjr., a crystal which oscillates at a frequency of 14.318MHz. This frequency is divided to obtain the many clocking signals used by the PC, XT and PCjr. There is a clock generator chip in these systems, the Intel 8284, which divides the 14.318MHz signal by 3 in order to derive the CPU frequency, 4.77MHz.
In order to overclock a PC, XT or PCjr., you must supply a higher clock signal to the CPU and only the CPU. Other components of the system and some expansion cards use the 14.318MHz frequency and do not work properly if it is changed. There is a small printed circuit board designed in the mid-1980s called "PC Sprint" which piggybacks or replaces the 8284 chip and hosts two 8284 chips. One 8284 processes the 14.318MHz signal normally, the other processes a higher frequency signal and send that only to the CPU's clock pin. The board has a jumper to allow you to use regular frequency instead of the higher frequency if needed for compatibility. The board is simple enough that its design has been reverse engineered and open sourced.
In the IBM PC and XT, the 8284 chip is usually socketed, making the installation of the PC Sprint board very easy. The IBM PCjr. has a soldered 8284, so installing the PC Sprint requires desoldering the existing 8284 and installing a socket into which the PC Sprint board can be fitted.
The PC Sprint has a clock crystal on it which dictates the resulting speed of the CPU. Although the CPU is running faster with a PC Sprint than without it, it is still constrained by other components in the system that expect a 4.77MHz CPU. The RAM and ROM only have a certain amount of time to respond to the CPU, so if the RAM is not fast enough to keep up with the faster CPU, the system will not be stable. You also need to ensure that your CPU is rated for the speed you wish to achieve. 8088 and V20s are rated to run at 5MHz, 8MHz or 10MHz and the chip markings (-2, -1/-10) will indicate whether the CPU is rated for faster than 5MHz operation.
This video was taken with my PCjr., first running an 8088 CPU at 4.77MHz and then running a V20 CPU at 7.37MHz. The frequency is derived from the clock crystal on the PC Sprint, which is 22.11MHz (divided by 3). The RAM and hard drive is provided by a jrIDE. jrIDE uses SRAM, which does not need to be refreshed, unlike DRAM. This gives a very slight improvement over contemporary DRAM-based PCjr. memory expansions. jrIDE is attached to a Compact Flash adapter and I am using a 1GB card for my "hard drive." I have heard stories of both success and failure with speeds significantly above 7.16MHz. A 50% overclock is still a very impressive feat for any system, and that extra speed comes in handy.
To demonstrate the speed differences, I captured the graphical boot screen and a little gameplay from four PCjr-appropriate games, King's Quest III, Leisure Suit Larry, Space Quest II and Manhunter: New York. All games are running from the Compact Flash card and using the latest game and interpreter versions. First I capture them at their standard 4.77MHz speed on the 8088 and then on their 7.37MHz speed on the V20. I edited out all the DOS screens in between running each game but not the loading times so you can get a reasonably accurate indication about how long it takes to load a game.
8088 @ 4.77MHz
00:00 - Boot
00:26 - KQ3
02:24 - LL
06:01 - SQ2
09:45 - MH
V20 @7.37MH z
16:54 - Boot
17:10 - KQ3
20:10 - LL
22:39 - SQ2
25:06 - MH
The IBM PCjr. used an Intel 8088 CPU running at 4.77MHz, like the IBM PC and IBM PC/XT that came before it. When running with 64-128KiB of RAM, its memory performance is severely compromised relative to a PC or XT because the PCjr. must share that memory with its video display hardware whereas on a PC or XT the video memory is separate from the system memory. When running programs above the 128KiB range, its performance is about equal to an PC or XT. Most IBM PCjrs used socketed CPUs, so their 8088s could be upgraded to NEC V20s for a 10-25% performance increase, depending on the application. A soldered CPU can be desoldered and replaced with a socket for the upgrade. That V20 will still be running at 4.77MHz if nothing else is done with the system.
There is a single clock source in a PC, XT or PCjr., a crystal which oscillates at a frequency of 14.318MHz. This frequency is divided to obtain the many clocking signals used by the PC, XT and PCjr. There is a clock generator chip in these systems, the Intel 8284, which divides the 14.318MHz signal by 3 in order to derive the CPU frequency, 4.77MHz.
In order to overclock a PC, XT or PCjr., you must supply a higher clock signal to the CPU and only the CPU. Other components of the system and some expansion cards use the 14.318MHz frequency and do not work properly if it is changed. There is a small printed circuit board designed in the mid-1980s called "PC Sprint" which piggybacks or replaces the 8284 chip and hosts two 8284 chips. One 8284 processes the 14.318MHz signal normally, the other processes a higher frequency signal and send that only to the CPU's clock pin. The board has a jumper to allow you to use regular frequency instead of the higher frequency if needed for compatibility. The board is simple enough that its design has been reverse engineered and open sourced.
In the IBM PC and XT, the 8284 chip is usually socketed, making the installation of the PC Sprint board very easy. The IBM PCjr. has a soldered 8284, so installing the PC Sprint requires desoldering the existing 8284 and installing a socket into which the PC Sprint board can be fitted.
The PC Sprint has a clock crystal on it which dictates the resulting speed of the CPU. Although the CPU is running faster with a PC Sprint than without it, it is still constrained by other components in the system that expect a 4.77MHz CPU. The RAM and ROM only have a certain amount of time to respond to the CPU, so if the RAM is not fast enough to keep up with the faster CPU, the system will not be stable. You also need to ensure that your CPU is rated for the speed you wish to achieve. 8088 and V20s are rated to run at 5MHz, 8MHz or 10MHz and the chip markings (-2, -1/-10) will indicate whether the CPU is rated for faster than 5MHz operation.
This video was taken with my PCjr., first running an 8088 CPU at 4.77MHz and then running a V20 CPU at 7.37MHz. The frequency is derived from the clock crystal on the PC Sprint, which is 22.11MHz (divided by 3). The RAM and hard drive is provided by a jrIDE. jrIDE uses SRAM, which does not need to be refreshed, unlike DRAM. This gives a very slight improvement over contemporary DRAM-based PCjr. memory expansions. jrIDE is attached to a Compact Flash adapter and I am using a 1GB card for my "hard drive." I have heard stories of both success and failure with speeds significantly above 7.16MHz. A 50% overclock is still a very impressive feat for any system, and that extra speed comes in handy.
To demonstrate the speed differences, I captured the graphical boot screen and a little gameplay from four PCjr-appropriate games, King's Quest III, Leisure Suit Larry, Space Quest II and Manhunter: New York. All games are running from the Compact Flash card and using the latest game and interpreter versions. First I capture them at their standard 4.77MHz speed on the 8088 and then on their 7.37MHz speed on the V20. I edited out all the DOS screens in between running each game but not the loading times so you can get a reasonably accurate indication about how long it takes to load a game.
8088 @ 4.77MHz
00:00 - Boot
00:26 - KQ3
02:24 - LL
06:01 - SQ2
09:45 - MH
V20 @7.37MH z
16:54 - Boot
17:10 - KQ3
20:10 - LL
22:39 - SQ2
25:06 - MH










