Uploaded October 2018 | Updated September 2026, 4 hours ago
Learn how to assemble your new Aquaglide WindSUP and Sail Rigs.
Instructions:
* UNROLL THE BOARD ON A SMOOTH GROUND LIKE GRASS OR SAND
* PUSH AND TURN THE STEM AT THE CENTER OF THE VALVE UNTIL IT POPS OUT. INSERT THE HOSE WITH THE HALKEY ROBERTS ADAPTER
* PUT BOTH FEET ON THE HAND PUMP AND BEGIN PUMPING UNTIL THE BOARD IS COMPLETELY INFLATED
* REMOVE THE SAIL AND ACCESSORIES FROM THE BAG
ROLL OUT THE SAIL AND INSERT THE MAST PIECES ON THE MAST SLEEVES
* MAKE SURE THEY CONNECT INSERT THE MAST EXTENSION TO THE BOTTOM OF THE MAST
* THREAD THE ROPE AROUND THE PULLEY, MAKE SURE THEY LINE UP AND THAT THEY ARE NOT CROSSED OVER THIS WILL MAKE THE ROPE EASIER TO PULL AND IT WILL STOP THE ROPE WEARING DOWN AS MUCH
* IN THE BOTTOM OF THE EXTENSION YOU WILL FIND THE CLEATS, MAKE SURE THE ROPE RESTS IN THESE TEETH TO HOLD IT IN PLACE
* TIE OFF YOUR REMAINING SO YOU DON’T STEP ON IT
MAKE SURE THE SAIL IS RIGID AND PLACE THE BOOM
* AT THE HEAD OF THE BOOM YOU WILL SEE THE BOOM CLAMP, THIS ATTACHES ONTO THE MAST. USING THE ROPES MAKE SURE IS TIGHT AND SECURE WITHOUT CRUSHING THE MAST
* THE END OF THE BOOM ATTACHES TO THE CLEW. THERE IS A LOOP, PASS THE LOOP THROUGH THE EYELET OF THE SAIL, FOLD IT OVER AND HOOK IT BACK ONTO THE BOOM
* PULL THE ROPE TO CREATE A BIT OF TENSION IN THE SAIL AND LOCK IT IN THE CLEAT. TIE THE REMAIN ROPE
* INSERT THE FIN TAB INTO THE FIN BOX AND SLIDE TO THE SIDE. INSERT THE FIN AND SLIDE AS FAR BACK AS POSSIBLE
* ALIGN THE SCREW WITH THE FIN TAB AND TIGHT WITH A SCREWDRIVER
* SCREW THE MAST BASE TO THE BOARD AND PLACE THE SAIL RIG.
---------------------------------------
Follow us on:
WEB ‣ aquaglide.com
INSTAGRAM ‣ instagram.com/aquaglide
FACEBOOK ‣ facebook.com/Aquaglide
PINTEREST ‣ pinterest.com/Aquaglide
TWITTER ‣ twitter.com/Aquaglide
Learn how to assemble your new Aquaglide WindSUP and Sail Rigs.
Instructions:
* UNROLL THE BOARD ON A SMOOTH GROUND LIKE GRASS OR SAND
* PUSH AND TURN THE STEM AT THE CENTER OF THE VALVE UNTIL IT POPS OUT. INSERT THE HOSE WITH THE HALKEY ROBERTS ADAPTER
* PUT BOTH FEET ON THE HAND PUMP AND BEGIN PUMPING UNTIL THE BOARD IS COMPLETELY INFLATED
* REMOVE THE SAIL AND ACCESSORIES FROM THE BAG
ROLL OUT THE SAIL AND INSERT THE MAST PIECES ON THE MAST SLEEVES
* MAKE SURE THEY CONNECT INSERT THE MAST EXTENSION TO THE BOTTOM OF THE MAST
* THREAD THE ROPE AROUND THE PULLEY, MAKE SURE THEY LINE UP AND THAT THEY ARE NOT CROSSED OVER THIS WILL MAKE THE ROPE EASIER TO PULL AND IT WILL STOP THE ROPE WEARING DOWN AS MUCH
* IN THE BOTTOM OF THE EXTENSION YOU WILL FIND THE CLEATS, MAKE SURE THE ROPE RESTS IN THESE TEETH TO HOLD IT IN PLACE
* TIE OFF YOUR REMAINING SO YOU DON’T STEP ON IT
MAKE SURE THE SAIL IS RIGID AND PLACE THE BOOM
* AT THE HEAD OF THE BOOM YOU WILL SEE THE BOOM CLAMP, THIS ATTACHES ONTO THE MAST. USING THE ROPES MAKE SURE IS TIGHT AND SECURE WITHOUT CRUSHING THE MAST
* THE END OF THE BOOM ATTACHES TO THE CLEW. THERE IS A LOOP, PASS THE LOOP THROUGH THE EYELET OF THE SAIL, FOLD IT OVER AND HOOK IT BACK ONTO THE BOOM
* PULL THE ROPE TO CREATE A BIT OF TENSION IN THE SAIL AND LOCK IT IN THE CLEAT. TIE THE REMAIN ROPE
* INSERT THE FIN TAB INTO THE FIN BOX AND SLIDE TO THE SIDE. INSERT THE FIN AND SLIDE AS FAR BACK AS POSSIBLE
* ALIGN THE SCREW WITH THE FIN TAB AND TIGHT WITH A SCREWDRIVER
* SCREW THE MAST BASE TO THE BOARD AND PLACE THE SAIL RIG.
---------------------------------------
Follow us on:
WEB ‣ aquaglide.com
INSTAGRAM ‣ instagram.com/aquaglide
FACEBOOK ‣ facebook.com/Aquaglide
PINTEREST ‣ pinterest.com/Aquaglide
TWITTER ‣ twitter.com/Aquaglide
