Uploaded December 2020 | Updated November 2026, 4 hours ago
In this video, we’re going to show you how to replace a foamed-in door gasket in a refrigerator. This gasket fits into the gap between the inner and outer panels around the edge of the door on a side-by-side refrigerator. The inner and outer door panels are joined with adhesive, insulating foam. The door gasket seals the gap around the door to keep the cold air in. You might need to replace it if you notice excessive frost buildup and reduced cooling or if the gasket is worn, cracked or torn.
This repair procedure can be used on many Kenmore, Whirlpool, Crosley and Amana refrigerators.
To smooth creases and folds in the gasket, carefully warm it with a hair dryer or heat gun on a low setting. Be careful not to melt the gasket. You can also soak it in warm water.
Replace the gasket:
1. First, unplug the refrigerator or shut off the circuit breaker for the refrigerator.
2. Pull the gasket out from the gap between the inner and outer door panels. Starting at a spot halfway down the side of the door is usually easiest. You may need to tug the gasket firmly to get the removal process started.
3. Using a wet cloth, wipe any spills from the outside edge of the outer door panel.
4. Slide the edge of a putty knife through the gap between inner and outer door panels to remove any foam residue that clings to gasket mounting surfaces. Don't insert the putty knife more than 1 inch into the inner door panel to avoid damaging insulation inside the door.
5. Starting at the top of the door, work the new door gasket lip into the gap between the inner and outer door panels. Work your way down both sides of the door and across the bottom.
6. Check for loose spots and adjust the gasket as needed for a proper fit.
7. Spread a thin coat of petroleum jelly along the sealing surface of the door gasket to help the new gasket seal properly.
8. Close the door and check the fit. The door gasket should fit tightly against the cabinet and door with no gaps showing. Smooth out any creases that cause gaps between the gasket and cabinet.
9. Turn the refrigerator back on or restore power to the refrigerator.
10. Use the same procedure to replace the freezer door gasket.
We hope this video helped you out today. Please subscribe to our channel to see more repair tips and tricks.
For more DIY help, visit
searspartsdirect.com/diy/repair-help?sid=soc:youtube:DIY
Find parts for your refrigerator at
searspartsdirect.com/category/1234589/refrigerator-parts?sid=soc:youtube:refrigerator-parts
In this video, we’re going to show you how to replace a foamed-in door gasket in a refrigerator. This gasket fits into the gap between the inner and outer panels around the edge of the door on a side-by-side refrigerator. The inner and outer door panels are joined with adhesive, insulating foam. The door gasket seals the gap around the door to keep the cold air in. You might need to replace it if you notice excessive frost buildup and reduced cooling or if the gasket is worn, cracked or torn.
This repair procedure can be used on many Kenmore, Whirlpool, Crosley and Amana refrigerators.
To smooth creases and folds in the gasket, carefully warm it with a hair dryer or heat gun on a low setting. Be careful not to melt the gasket. You can also soak it in warm water.
Replace the gasket:
1. First, unplug the refrigerator or shut off the circuit breaker for the refrigerator.
2. Pull the gasket out from the gap between the inner and outer door panels. Starting at a spot halfway down the side of the door is usually easiest. You may need to tug the gasket firmly to get the removal process started.
3. Using a wet cloth, wipe any spills from the outside edge of the outer door panel.
4. Slide the edge of a putty knife through the gap between inner and outer door panels to remove any foam residue that clings to gasket mounting surfaces. Don't insert the putty knife more than 1 inch into the inner door panel to avoid damaging insulation inside the door.
5. Starting at the top of the door, work the new door gasket lip into the gap between the inner and outer door panels. Work your way down both sides of the door and across the bottom.
6. Check for loose spots and adjust the gasket as needed for a proper fit.
7. Spread a thin coat of petroleum jelly along the sealing surface of the door gasket to help the new gasket seal properly.
8. Close the door and check the fit. The door gasket should fit tightly against the cabinet and door with no gaps showing. Smooth out any creases that cause gaps between the gasket and cabinet.
9. Turn the refrigerator back on or restore power to the refrigerator.
10. Use the same procedure to replace the freezer door gasket.
We hope this video helped you out today. Please subscribe to our channel to see more repair tips and tricks.
For more DIY help, visit
searspartsdirect.com/diy/repair-help?sid=soc:youtube:DIY
Find parts for your refrigerator at
searspartsdirect.com/category/1234589/refrigerator-parts?sid=soc:youtube:refrigerator-parts










