GT Woodshop | How to make Solid Wood Nespresso Coffee Pod Holder on your Router Table using the Incra Fence System @GTWoodshop | Uploaded September 2021 | Updated October 2024, 21 hours ago.
As promised in my last video 'Installing the Incra Router Lift and AukTools Router' this is the first in a short(ish) series on Router Table projects.
In this video I show you how to make a simple but elegant and practical Coffee Pod Stand in Hard wood.
Link to installing the new Router and Lift:
youtu.be/aGJrVJBjIQ4
Tools used:
Straight Router bit: 12-627
infinitytools.co.uk/router-bits/straight-bit-half-inch-shank
T Slot Router Bit:
Whiteside 3070 amzn.to/3gYZRLM
9mm Round over bearing guided bit:
axminstertools.com/axcaliber-ovolo-cutter-d-31-75-x-15-88-r-9-53mm-s-1-2-12-7mm-666054
3.2mm Round over bearing guided bit:
axminstertools.com/axcaliber-ovolo-cutter-d-19-05-x-9-53-r-3-2mm-s-1-4-6-35mm-666047
Incra Tools Push Block: incrementaltools.com/INCRA_PushGuard_Combo_Push_Block_Hand_Guard_p/inc-pushguard.htm
Sizes and settings:
Blank size 300mm x 260mm x 30mm
Router Fence, 0 set to center of Router Bit.
Router Table Fence Stop set to approx 80mm.
Support piece cut of blade angle 10 degrees, length approx 50mm.
Router table fence positions for Straight Cutter:
36 - 54 - 47
86 - 104 - 97
136 - 154 - 147
186 - 204 - 197
Router table fence positions for T Slot Cutter:
38 - 52
88 - 102
138 - 152
188 - 202
Thanks for watching.
My Amazon Associate Page.
Any items you purchase from this page helps to support the channel by giving me a small kick back from Amazon.
amazon.co.uk/shop/gtwoodshop
I will keep adding to this as I get time to build a full list of the tools I use in my workshop.
If you enjoyed this video then please consider giving up one of your likes. 😊
If you 'really' enjoyed this video then why not Subscribe. 😁
If you would like to help support this channel then please consider becoming a Patreon. 😁😁👍
patreon.com/user?u=44803266&fan_landing=true
As promised in my last video 'Installing the Incra Router Lift and AukTools Router' this is the first in a short(ish) series on Router Table projects.
In this video I show you how to make a simple but elegant and practical Coffee Pod Stand in Hard wood.
Link to installing the new Router and Lift:
youtu.be/aGJrVJBjIQ4
Tools used:
Straight Router bit: 12-627
infinitytools.co.uk/router-bits/straight-bit-half-inch-shank
T Slot Router Bit:
Whiteside 3070 amzn.to/3gYZRLM
9mm Round over bearing guided bit:
axminstertools.com/axcaliber-ovolo-cutter-d-31-75-x-15-88-r-9-53mm-s-1-2-12-7mm-666054
3.2mm Round over bearing guided bit:
axminstertools.com/axcaliber-ovolo-cutter-d-19-05-x-9-53-r-3-2mm-s-1-4-6-35mm-666047
Incra Tools Push Block: incrementaltools.com/INCRA_PushGuard_Combo_Push_Block_Hand_Guard_p/inc-pushguard.htm
Sizes and settings:
Blank size 300mm x 260mm x 30mm
Router Fence, 0 set to center of Router Bit.
Router Table Fence Stop set to approx 80mm.
Support piece cut of blade angle 10 degrees, length approx 50mm.
Router table fence positions for Straight Cutter:
36 - 54 - 47
86 - 104 - 97
136 - 154 - 147
186 - 204 - 197
Router table fence positions for T Slot Cutter:
38 - 52
88 - 102
138 - 152
188 - 202
Thanks for watching.
My Amazon Associate Page.
Any items you purchase from this page helps to support the channel by giving me a small kick back from Amazon.
amazon.co.uk/shop/gtwoodshop
I will keep adding to this as I get time to build a full list of the tools I use in my workshop.
If you enjoyed this video then please consider giving up one of your likes. 😊
If you 'really' enjoyed this video then why not Subscribe. 😁
If you would like to help support this channel then please consider becoming a Patreon. 😁😁👍
patreon.com/user?u=44803266&fan_landing=true
