Uploaded April 2022 | Updated November 2026, 4 days ago
Gear & Studio Setup List: vonmalegowski.blogspot.com/2020/06/von-malegowskis-equipment-list-2020.html
This mycology tutorial demonstrates how to build autoclavable, reusable mason jar lids designed for sterile mushroom cultivation. Equipped with a self-healing rubber injection port (SHIP) for sterile needle inoculations and a 0.22 µm PTFE syringe filter for contaminant-free gas exchange, these modified lids eliminate the need to open jars during colonization. They withstand standard pressure-cooker sterilization cycles (15 PSI) and are suitable for liquid culture (LC), sterilized grain spawn jars, BRF (PF Tek) cakes, and no-pour agar containers.
Equipment & Supplies
Self-Healing Rubber Injection Ports (13 mm / 20 mm): https://link.amazon/B0f2RCNaU
0.22 µm Hydrophobic Syringe Filters: https://link.amazon/B03RU5FhQ
Ball Mason Jar Metal Lids & Bands: https://link.amazon/B04awK6Gt
Ball Wide-Mouth Mason Jars: https://link.amazon/B00eTCCzI
Stovetop Pressure Canner (15 PSI): https://link.amazon/B01PIWxrX
Timestamps
0:00 Introduction
0:57 Making the Lids
3:19 Alternative Materials
4:05 Outro
Step-by-Step Assembly
1. Mark two holes on the top of a metal or plastic mason jar lid: one sized for the self-healing injection port (typically 1/4" to 1/2" depending on port design) and a smaller hole sized to receive the tip of the syringe filter.
2. Drill or punch the holes cleanly from the top side down, then remove any sharp metal burrs with a file or countersink bit to protect the rubber port from tearing.
3. Press the self-healing rubber injection port firmly into its hole (adding a bead of high-temp red RTV silicone if necessary to ensure a hermetic seal).
4. Insert the syringe filter into the gas exchange hole and secure it flush against the lid with high-temperature silicone.
5. Allow all silicone to cure fully before loading jars into a pressure cooker for steam sterilization.
Alternative Material Options
Gas Exchange Alternatives: Synthetic filter discs (SFD), multiple layers of breathable micropore surgical tape, or packed synthetic polyester polyfill stuffing.
Port Alternatives: High-temperature red RTV gasket maker silicone cured in place of pre-molded rubber ports.
Always vent your pressure cooker properly and maintain 15 PSI for the full sterilization duration required for your specific substrate or grain volume. Wear heat-resistant gloves when handling hot canning jars from the cooker, and perform all inoculations inside a still air box (SAB) or laminar flow hood to maintain sterility.
Photos and Videos Creative Commons Attribution
How to make a Liquid Culture for Growing Mushroom Mycelium | Quickest way to make Liquid Culture, by Mycotopia (support.google.com/youtube/answer/2797468)
Using My DIY Still Air Box, by DIY Mushroom Enthusiasts (support.google.com/youtube/answer/2797468)
Music by Karl Casey @ White Bat Audio
Tracks: Legend, Existence
#Mycology #MushroomCultivation #GrainSpawn
©Von Malegowski. All Rights Reserved.
Gear & Studio Setup List: vonmalegowski.blogspot.com/2020/06/von-malegowskis-equipment-list-2020.html
This mycology tutorial demonstrates how to build autoclavable, reusable mason jar lids designed for sterile mushroom cultivation. Equipped with a self-healing rubber injection port (SHIP) for sterile needle inoculations and a 0.22 µm PTFE syringe filter for contaminant-free gas exchange, these modified lids eliminate the need to open jars during colonization. They withstand standard pressure-cooker sterilization cycles (15 PSI) and are suitable for liquid culture (LC), sterilized grain spawn jars, BRF (PF Tek) cakes, and no-pour agar containers.
Equipment & Supplies
Self-Healing Rubber Injection Ports (13 mm / 20 mm): https://link.amazon/B0f2RCNaU
0.22 µm Hydrophobic Syringe Filters: https://link.amazon/B03RU5FhQ
Ball Mason Jar Metal Lids & Bands: https://link.amazon/B04awK6Gt
Ball Wide-Mouth Mason Jars: https://link.amazon/B00eTCCzI
Stovetop Pressure Canner (15 PSI): https://link.amazon/B01PIWxrX
Timestamps
0:00 Introduction
0:57 Making the Lids
3:19 Alternative Materials
4:05 Outro
Step-by-Step Assembly
1. Mark two holes on the top of a metal or plastic mason jar lid: one sized for the self-healing injection port (typically 1/4" to 1/2" depending on port design) and a smaller hole sized to receive the tip of the syringe filter.
2. Drill or punch the holes cleanly from the top side down, then remove any sharp metal burrs with a file or countersink bit to protect the rubber port from tearing.
3. Press the self-healing rubber injection port firmly into its hole (adding a bead of high-temp red RTV silicone if necessary to ensure a hermetic seal).
4. Insert the syringe filter into the gas exchange hole and secure it flush against the lid with high-temperature silicone.
5. Allow all silicone to cure fully before loading jars into a pressure cooker for steam sterilization.
Alternative Material Options
Gas Exchange Alternatives: Synthetic filter discs (SFD), multiple layers of breathable micropore surgical tape, or packed synthetic polyester polyfill stuffing.
Port Alternatives: High-temperature red RTV gasket maker silicone cured in place of pre-molded rubber ports.
Always vent your pressure cooker properly and maintain 15 PSI for the full sterilization duration required for your specific substrate or grain volume. Wear heat-resistant gloves when handling hot canning jars from the cooker, and perform all inoculations inside a still air box (SAB) or laminar flow hood to maintain sterility.
Photos and Videos Creative Commons Attribution
How to make a Liquid Culture for Growing Mushroom Mycelium | Quickest way to make Liquid Culture, by Mycotopia (support.google.com/youtube/answer/2797468)
Using My DIY Still Air Box, by DIY Mushroom Enthusiasts (support.google.com/youtube/answer/2797468)
Music by Karl Casey @ White Bat Audio
Tracks: Legend, Existence
#Mycology #MushroomCultivation #GrainSpawn
©Von Malegowski. All Rights Reserved.










