Uploaded January 2026 | Updated November 2026, 2 days ago
Selecting the right MOSFET can make or break a power-switching design, whether you're driving LEDs, motors, or other loads from a microcontroller. This video walks through the essential steps of choosing a MOSFET, focusing on the practical parameters that determine reliability, efficiency, and performance in real-world circuits.
We begin with a quick refresher on what a MOSFET is: an electronic switch that uses a small control signal to handle larger voltages and currents. If you already have a basic understanding of MOSFET operation but need guidance on selecting one for your project, this video is designed for you.
1. MOSFET Types and Use Cases
Many Makers, engineers, and hobbyists rely on N-channel MOSFETs for low-side switching, placing the MOSFET between the load and ground. They typically offer lower on-resistance and better efficiency compared to P-channel MOSFETs, making them a common go-to for controlling DC loads.
2. Voltage Ratings: VDS & VGS
We explain how to evaluate two critical voltage specifications:
• Drain-Source Voltage (VDS): Choose a MOSFET rated comfortably above your supply voltage. A good rule of thumb is selecting a device with at least 1.5× to 2× the expected load voltage. This extra margin protects against ringing, spikes, and other transient events that can damage the device.
• Gate-Source Voltage (VGS): Ensure the MOSFET can safely tolerate the voltage you’re using to turn it on. While many MOSFETs have a very low threshold voltage, they may also have a maximum VGS rating (for example, ±8V or ±12V). Exceeding this limit can overstress or destroy the gate. Always check that your microcontroller or driver stays within the allowable range.
3. Current Rating & RDS(on)
The current a MOSFET must carry is just as important as the voltage it must withstand.
• Drain Current (ID): Look for the continuous drain current value and ensure it exceeds the expected load current. As with voltage, some margin is recommended to reduce thermal stress.
• RDS(on): This is the resistance across the MOSFET when it is fully on. Lower RDS(on) results in less heat, lower power loss, and higher efficiency. For high-current or battery-powered designs, a low RDS(on) can make a substantial difference in performance.
4. Switching Speed Considerations
If your design uses PWM such as in dimming, motor control, or DC-DC converters, switching speed becomes a major factor.
• Gate Charge (Qg): MOSFETs with lower gate charge switch faster and are easier for microcontrollers or gate drivers to control. Faster switching means less heat and better efficiency in high-frequency applications.
5. Putting It All Together
The video walks through a practical example to show the selection process in context: controlling a load with a typical microcontroller, evaluating the required headroom on voltage and current, verifying that the gate drive is within limits, and checking RDS(on) to maintain efficient operation.
While the example uses a 12-volt LED strip and a 5-volt microcontroller, the methodology applies to nearly any MOSFET-based power-switching application. By understanding how each datasheet parameter affects performance, you can confidently choose a MOSFET for motor control, lighting, power converters, and more.
Link: digikey.com/en/blog/how-to-select-a-mosfet-for-logic-circuits-or-gate-design
Learn more:
Maker.io - digikey.com/en/maker
DigiKey’s Blog – TheCircuit digikey.com/en/blog
Connect with DigiKey on Facebook facebook.com/digikey.electronics
And follow us on X https://x.com/digikey
Selecting the right MOSFET can make or break a power-switching design, whether you're driving LEDs, motors, or other loads from a microcontroller. This video walks through the essential steps of choosing a MOSFET, focusing on the practical parameters that determine reliability, efficiency, and performance in real-world circuits.
We begin with a quick refresher on what a MOSFET is: an electronic switch that uses a small control signal to handle larger voltages and currents. If you already have a basic understanding of MOSFET operation but need guidance on selecting one for your project, this video is designed for you.
1. MOSFET Types and Use Cases
Many Makers, engineers, and hobbyists rely on N-channel MOSFETs for low-side switching, placing the MOSFET between the load and ground. They typically offer lower on-resistance and better efficiency compared to P-channel MOSFETs, making them a common go-to for controlling DC loads.
2. Voltage Ratings: VDS & VGS
We explain how to evaluate two critical voltage specifications:
• Drain-Source Voltage (VDS): Choose a MOSFET rated comfortably above your supply voltage. A good rule of thumb is selecting a device with at least 1.5× to 2× the expected load voltage. This extra margin protects against ringing, spikes, and other transient events that can damage the device.
• Gate-Source Voltage (VGS): Ensure the MOSFET can safely tolerate the voltage you’re using to turn it on. While many MOSFETs have a very low threshold voltage, they may also have a maximum VGS rating (for example, ±8V or ±12V). Exceeding this limit can overstress or destroy the gate. Always check that your microcontroller or driver stays within the allowable range.
3. Current Rating & RDS(on)
The current a MOSFET must carry is just as important as the voltage it must withstand.
• Drain Current (ID): Look for the continuous drain current value and ensure it exceeds the expected load current. As with voltage, some margin is recommended to reduce thermal stress.
• RDS(on): This is the resistance across the MOSFET when it is fully on. Lower RDS(on) results in less heat, lower power loss, and higher efficiency. For high-current or battery-powered designs, a low RDS(on) can make a substantial difference in performance.
4. Switching Speed Considerations
If your design uses PWM such as in dimming, motor control, or DC-DC converters, switching speed becomes a major factor.
• Gate Charge (Qg): MOSFETs with lower gate charge switch faster and are easier for microcontrollers or gate drivers to control. Faster switching means less heat and better efficiency in high-frequency applications.
5. Putting It All Together
The video walks through a practical example to show the selection process in context: controlling a load with a typical microcontroller, evaluating the required headroom on voltage and current, verifying that the gate drive is within limits, and checking RDS(on) to maintain efficient operation.
While the example uses a 12-volt LED strip and a 5-volt microcontroller, the methodology applies to nearly any MOSFET-based power-switching application. By understanding how each datasheet parameter affects performance, you can confidently choose a MOSFET for motor control, lighting, power converters, and more.
Link: digikey.com/en/blog/how-to-select-a-mosfet-for-logic-circuits-or-gate-design
Learn more:
Maker.io - digikey.com/en/maker
DigiKey’s Blog – TheCircuit digikey.com/en/blog
Connect with DigiKey on Facebook facebook.com/digikey.electronics
And follow us on X https://x.com/digikey

![All Wound Up [Maker Update] | Maker.io
This week on Maker Update: on a wing and a prayer, making your own RAM in a shed, corrugated starships, and indestructible PLA parts.
+Show Notes [Maker Update Ep.481]+
=Project of the Week=
Super Capacitor Wind Up Plane by Tom Stanton 0:28
https://www.youtube.com/watch?v 4X6KYlQ7YQ
=More Projects=
Making RAM at Home by Dr. Semiconductor 2:40
https://www.youtube.com/watch?v=h6GWikWlAQA
3d Printed Pinball by 3d Printer Academy 3:30
https://www.youtube.com/watch?v=r7c_iTuHRgs
Cardboard Star Wars by Zach King 4:50
https://www.youtube.com/watch?v=ulVscDewRPI
=Tips & Tools=
Indestructible PLA by Makers Muse 5:24
https://www.youtube.com/watch?v=c7CI6yBTKMc
The Quietest Servo by Will Cogley 5:59
https://www.youtube.com/watch?v=G8TKJH7o5Fs
Shop Servos on DigiKey:
https://www.digikey.com/short/np4n89r0
Repair Box by Duct Tapers Anonymous 6:45
https://www.youtube.com/watch?v=2BwVKB1s4JA
Time of Flight Sensor to 3d Scanner by Henrique Ferrolho 7:19
https://www.youtube.com/watch?v=s32OUzhjf4U
Shop Time of Flight Sensors on DigiKey:
https://www.digikey.com/short/5mbq3573
=DigiKey Spotlight=
How to Choose a Mosfet 7:53
https://www.youtube.com/watch?v=e19derT5z9A
https://www.youtube.com/watch?v=F485AB1B1_Y
#makerupdate
Maker Update is a weekly video series covering news, projects, tips, and events that interest the maker and DIY community.
Find more online:
Blog: http://makerprojectlab.com
Instagram: https://www.instagram.com/makerprojectlab/ All Wound Up [Maker Update] | Maker.io](https://i.ytimg.com/vi/eeGZ0l2yWeY/mqdefault.jpg)

![Face It [Maker Update] | Maker.io
Face It [Maker Update] | Maker.io Face It [Maker Update] | Maker.io](https://i.ytimg.com/vi/f3_lLdpr6bs/mqdefault.jpg)



![Seeing Double [Maker Update] | Maker.io
This week on Maker Update: a lamp that’s through the looking glass, a butterfly you can steer, a 3d printed vending machine, and how to use free weights as a battery.
+Show Notes [Maker Update Ep.469]+
=Project of the Week=
Kaleidoscope Lamp by Simone Giertz 0:31
https://www.youtube.com/watch?v=GPSNT5vjSO8
=More Projects=
RC Butterfly by S-DIY 2:56
https://www.youtube.com/watch?v=eLTltRwuGW8
Making Furniture from Tiny Objects by Rachel Maksy 4:01
https://www.youtube.com/watch?v=z90eikSwvhc
3d Printed Vending Machine by DevMode Makes 5:03
https://www.youtube.com/watch?v=iorlgZoYXaQ
=Tips & Tools=
Testing Advanced 3d Printing Materials by Makers Muse 5:43
https://www.youtube.com/watch?v=Lo6UdFKQO0c
Can a Pendulum be a Battery by Tom Stanton 6:22
https://www.youtube.com/watch?v=uqmT1GzRXWI
TrueNAS Deep Dive by Zack Freedman 7:01
https://www.youtube.com/watch?v=n4wDmjEn8Vo
=DigiKey Spotlight=
Embedded Rust by Shawn Hymel 7:45
https://www.youtube.com/watch?v=mz-vW-Ar_GM
#makerupdate
Maker Update is a weekly video series covering news, projects, tips, and events that interest the maker and DIY community.
Find more online:
Blog: http://makerprojectlab.com
Instagram: https://www.instagram.com/makerprojectlab/ Seeing Double [Maker Update] | Maker.io](https://i.ytimg.com/vi/fyR3Dv0BOlo/mqdefault.jpg)


![In My Lane, Flourishing [Maker Update] | Maker.io
This week on Maker Update: bowling 300 in your kitchen, knights of the Canadian tuxedo, a dimpled display, and a control board for tiny bots.
+Show Notes [Maker Update Ep.471]+
=Project of the Week=
Mini Bowling Lane by Danny Lum 0:31
https://www.youtube.com/watch?v=sriRDDAa19A
=More Projects=
Armor Made From Jeans by Miss Twisted 2:58
https://www.youtube.com/watch?v=eIpotKXXrBI
Air Powered Display by Soiboi Soft 4:03
https://www.youtube.com/watch?v=VZ2ZcOzLnGg
R2-Cthru by Swooshdave 5:15
https://www.youtube.com/watch?v=PemdlFmORNs
=Tips & Tools=
Smallest Robotic Drive by Microbots 6:01
https://www.youtube.com/watch?v=uoak2QaHMsI
Design for Any Thread by Salveo3d 6:41
https://www.youtube.com/shorts/n8MxYaiIvno
3d Printed Furniture by Paul Lagier 7:13
https://www.youtube.com/watch?v=f3j8getccfA
=DigiKey Spotlight=
Making Sound Reactive Projects by Becky Stern 7:56
https://www.youtube.com/watch?v=TnpJTVUOYdA
#makerupdate
Maker Update is a weekly video series covering news, projects, tips, and events that interest the maker and DIY community.
Find more online:
Blog: http://makerprojectlab.com
Instagram: https://www.instagram.com/makerprojectlab/ In My Lane, Flourishing [Maker Update] | Maker.io](https://i.ytimg.com/vi/gBiG8B-54S4/mqdefault.jpg)