Uploaded September 2015 | Updated November 2026, 22 hours ago
In this video, I go through a step-by-step process for how to build your very own Schlieren setup. First, I go through the basic theory and overview. Then I describe all the materials you'll need. Finally, I walk you through the full setup. By the end of the video, you should have no problem getting some nice pictures or videos with your at-home system.
00:00 - Introduction
00:36 - Theory
03:19 - Materials
09:39 - Initial Placement
12:19 - Finding 2f
14:28 - Add LED Mask
15:27 - Add Camera and Alignment
20:12 - Bathroom Mirror
Note: I will sometimes say 'laser' when I actually mean 'LED'. You will have to forgive me; I work with lasers in my research and have become accustomed to saying 'laser' whenever talking about some sort of source.
Below are some website links that I found useful/referenced while going through my own setup.
General Schlieren Knowledge
goo.gl/gI1YQq
goo.gl/pLwii8
goo.gl/uonkOt
goo.gl/RFCSuG
goo.gl/hegJHF
goo.gl/YD0i0c
Interesting Mirror Articles (slightly advanced)
goo.gl/t16ePi
goo.gl/BAL6Bj
Want some more theory? Here's a video with some great visuals to aid your understanding.
goo.gl/b31aOS
Other Papers (you can search on Google for these)
"Hypersonic Application of Focused Schlieren and Deflectometry"
"Flow Visualization for Supersonic Flow Past a Wedge"
"An Overview on Schlieren Optics and its Applications"
"Design, Assembly, and Calibration of a Focusing Schlieren System"
"Introduction to Shadowgraph and Schlieren Imaging"
Below are little sections about the materials and where to find them (Amazon affiliate links).
LED Light Source (goo.gl/bPbJx9)
You can find tons of LEDs on Amazon. You will only need one, and I prefer a bright white LED, as seen in the link above. If you buy these, you'll end up with 49 extra, and who doesn't want an extra 49 LEDs lying around their house? I personally bought a single white LED from Radio Shack before the store closed at the mall.
Resistors (470 Ohm) (goo.gl/XNH8u9)
To build your own LED circuit, you'll need this particular resistor. The value comes from the fact that you are using a 9 volt battery, and that the white LED has a forward voltage of about 2 V and a current rating of about 20 mA. Using these values, you would need a resistor of 350 Ohms, but I've found it is better to be on the higher resistance side, and 470 Ohms is the next highest resistor you can use without having to wire together a series or parallel circuit to get the most accurate value. It's a compromise between simplicity and efficiency. Above is a link to a pack on Amazon, although you'll only need one.
Circuit Board (goo.gl/tKNaFH)
If you're making your own circuit (like I did), you'll want a circuit board to solder all your materials together. This one from Amazon seemed like a good bet. I bought mine straight from the Radio Shack at the mall.
9V Battery Connector (goo.gl/oL7M3g)
To finish off the circuit, you'll need some way to connect the 9V battery. Above is a link to a 9V battery connector.
Knife Edge (Single Edge Razor Blade) (goo.gl/zCyNt1)
This is again one of those items where you only need one, but you'll end up buying a thousand. Above is a link on Amazon, but they sell them at any store like Target.
Mirror (Spherical Concave)
It looks like the mirror that I use has officially been fully sold out (from both Anchor Optics and now Edmund Optics). I'll be looking for an inexpensive alternative with the same quality, and will update this section if I find one. If you find an option, please leave a comment letting me know so I can update this section! Small focal length mirrors won't give you the sensitivity you need, so make sure to get a longer focal length mirror. Note that Z-type systems will use two parabolic mirrors, while this double-pass system uses one spherical concave mirror (parabolic is okay too).
Camera (goo.gl/KmPwy7)
I personally use my Nikon D3200 DSLR camera with its 18-55mm f/3.5-5.6 kit lens. I use this lens so I can zoom in on the mirror. I also have a 35mm f/1.8 prime lens, but it can't zoom (obviously), so I don't see that being as useful. Above is a link for the camera I have on Amazon (newer model).
I have used my point-and-shoot camera and Samsung S6 phone to get videos and pictures as well. I mention this just so you realize you don't absolutely need to buy a DSLR camera. However, I will say the quality of the DSLR videos/images was much better than the other two. It gives you more control over settings, and will make your life much easier.
Tripod (goo.gl/oKmyU8)
I use two tripods during the video. The tripod that I use to mount the LED and knife-edge is a cheap plastic one that I got a while ago. I purchased a higher quality tripod recently, and if you're looking for a low-cost, good quality tripod, I would recommend the one provided in the link.
In this video, I go through a step-by-step process for how to build your very own Schlieren setup. First, I go through the basic theory and overview. Then I describe all the materials you'll need. Finally, I walk you through the full setup. By the end of the video, you should have no problem getting some nice pictures or videos with your at-home system.
00:00 - Introduction
00:36 - Theory
03:19 - Materials
09:39 - Initial Placement
12:19 - Finding 2f
14:28 - Add LED Mask
15:27 - Add Camera and Alignment
20:12 - Bathroom Mirror
Note: I will sometimes say 'laser' when I actually mean 'LED'. You will have to forgive me; I work with lasers in my research and have become accustomed to saying 'laser' whenever talking about some sort of source.
Below are some website links that I found useful/referenced while going through my own setup.
General Schlieren Knowledge
goo.gl/gI1YQq
goo.gl/pLwii8
goo.gl/uonkOt
goo.gl/RFCSuG
goo.gl/hegJHF
goo.gl/YD0i0c
Interesting Mirror Articles (slightly advanced)
goo.gl/t16ePi
goo.gl/BAL6Bj
Want some more theory? Here's a video with some great visuals to aid your understanding.
goo.gl/b31aOS
Other Papers (you can search on Google for these)
"Hypersonic Application of Focused Schlieren and Deflectometry"
"Flow Visualization for Supersonic Flow Past a Wedge"
"An Overview on Schlieren Optics and its Applications"
"Design, Assembly, and Calibration of a Focusing Schlieren System"
"Introduction to Shadowgraph and Schlieren Imaging"
Below are little sections about the materials and where to find them (Amazon affiliate links).
LED Light Source (goo.gl/bPbJx9)
You can find tons of LEDs on Amazon. You will only need one, and I prefer a bright white LED, as seen in the link above. If you buy these, you'll end up with 49 extra, and who doesn't want an extra 49 LEDs lying around their house? I personally bought a single white LED from Radio Shack before the store closed at the mall.
Resistors (470 Ohm) (goo.gl/XNH8u9)
To build your own LED circuit, you'll need this particular resistor. The value comes from the fact that you are using a 9 volt battery, and that the white LED has a forward voltage of about 2 V and a current rating of about 20 mA. Using these values, you would need a resistor of 350 Ohms, but I've found it is better to be on the higher resistance side, and 470 Ohms is the next highest resistor you can use without having to wire together a series or parallel circuit to get the most accurate value. It's a compromise between simplicity and efficiency. Above is a link to a pack on Amazon, although you'll only need one.
Circuit Board (goo.gl/tKNaFH)
If you're making your own circuit (like I did), you'll want a circuit board to solder all your materials together. This one from Amazon seemed like a good bet. I bought mine straight from the Radio Shack at the mall.
9V Battery Connector (goo.gl/oL7M3g)
To finish off the circuit, you'll need some way to connect the 9V battery. Above is a link to a 9V battery connector.
Knife Edge (Single Edge Razor Blade) (goo.gl/zCyNt1)
This is again one of those items where you only need one, but you'll end up buying a thousand. Above is a link on Amazon, but they sell them at any store like Target.
Mirror (Spherical Concave)
It looks like the mirror that I use has officially been fully sold out (from both Anchor Optics and now Edmund Optics). I'll be looking for an inexpensive alternative with the same quality, and will update this section if I find one. If you find an option, please leave a comment letting me know so I can update this section! Small focal length mirrors won't give you the sensitivity you need, so make sure to get a longer focal length mirror. Note that Z-type systems will use two parabolic mirrors, while this double-pass system uses one spherical concave mirror (parabolic is okay too).
Camera (goo.gl/KmPwy7)
I personally use my Nikon D3200 DSLR camera with its 18-55mm f/3.5-5.6 kit lens. I use this lens so I can zoom in on the mirror. I also have a 35mm f/1.8 prime lens, but it can't zoom (obviously), so I don't see that being as useful. Above is a link for the camera I have on Amazon (newer model).
I have used my point-and-shoot camera and Samsung S6 phone to get videos and pictures as well. I mention this just so you realize you don't absolutely need to buy a DSLR camera. However, I will say the quality of the DSLR videos/images was much better than the other two. It gives you more control over settings, and will make your life much easier.
Tripod (goo.gl/oKmyU8)
I use two tripods during the video. The tripod that I use to mount the LED and knife-edge is a cheap plastic one that I got a while ago. I purchased a higher quality tripod recently, and if you're looking for a low-cost, good quality tripod, I would recommend the one provided in the link.
![Explained: Waitbar Color Change [MATLAB]
This video shows how you can change the color of your waitbar (progress bar) in your MATLAB code.
Basic waitbar video: http://www.youtube.com/watch?v=k2wKPxRUPiE Explained: Waitbar Color Change [MATLAB]](https://i.ytimg.com/vi/IjkajdAE8vA/mqdefault.jpg)
![Vortex Panel Method: Tangential Velocity Geometric Integral [L(ij)]
We just finished the video for the source panel method (SPM), and saw its inherent limitations as we looked at some results for an airfoil. Now, to be able to code up the vortex panel method (VPM), we need to compute geometric integrals similar to those for the SPM. These geometric integrals come from the expressions for the normal and tangential velocity.
In this video, we derive the geometric integral from the tangential velocity expression (Lij). In the next video, we will derive the X and Y velocity expression geometric integrals needed for the streamline calculations, after which we can construct a system of equations to solve for the vortex panel strengths.
RELEVANT VIDEOS
► Panel Methods Playlist
https://www.youtube.com/watch?v=bWjo3N9COz4&list=PLxT-itJ3HGuUDVMuWKBxyoY8Dm9O9qstP
NOTES
- Ill add notes here if I need to.
ERRORS
- If you see an error in the video, please let me know and I will include it here.
REFERENCES
Note: the links are Amazon affiliate links. If you do happen to want to buy the book and use the link below, it helps me out a little.
► Fundamentals of Aerodynamics, Anderson
https://amzn.to/3emVuXU
► Foundations of Aerodynamics, Kuethe and Chow
https://amzn.to/2yMg1Vi
► Theory of Wing Sections, Abbott and Doenhoff
https://amzn.to/2wvZyUt Vortex Panel Method: Tangential Velocity Geometric Integral [L(ij)]](https://i.ytimg.com/vi/IxWJzwIG_gY/mqdefault.jpg)
![Explained: NACA 4-Digit GUI Part 5/10 [MATLAB]
This is the fifth video in my 10-video series on coding a program in MATLAB to compute, display, and save a NACA 4-digit airfoil.
IN THIS VIDEO:
We code the input for the angle of attack and save file name edit text boxes. The angle of attack text box needs to be converted to a number, while the file name text box can remain a string.
IN THIS SERIES:
Part 1/10 : https://goo.gl/9UBgbo
Part 2/10 : https://goo.gl/jRRcYJ
Part 3/10 : https://goo.gl/rSVLHo
Part 4/10 : https://goo.gl/HwHB39
Part 5/10 : https://goo.gl/AlDne8
Part 6/10 : https://goo.gl/7n1QP7
Part 7/10 : https://goo.gl/nTGleR
Part 8/10 : https://goo.gl/ez247P
Part 9/10 : https://goo.gl/8mXYcc
Part 10/10: https://goo.gl/ovBlbW Explained: NACA 4-Digit GUI Part 5/10 [MATLAB]](https://i.ytimg.com/vi/J0L7N7cvk80/mqdefault.jpg)
![Explained: Oblique Shock Relations Derivation
In this video, we will derive the oblique shock (OS) relations. We will start from integral conservation equations, and derive expressions for the downstream Mach number, density ratio, velocity ratio, pressure ratio, and temperature ratio.
RELEVANT VIDEOS
→ Oblique Shock Example
https://goo.gl/77hjcb
→ Normal Shock Relations Derivation
https://goo.gl/Unvjey
→ Normal Shock Example
https://goo.gl/RBJtgV
RELEVANT LINKS
► Surface (Double) Integrals Explanation
http://www.joshtheengineer.com/2017/01/02/surface-double-integrals/
► VT Calculator
http://www.dept.aoe.vt.edu/~devenpor/aoe3114/calc.html
► MATLAB Functions
https://github.com/jte0419/Compressible_Flow_Relations
THUMBNAIL CREDIT
By Settles1 (Own work) [CC BY-SA 4.0 (https://creativecommons.org/licenses/by-sa/4.0)], via Wikimedia Commons Explained: Oblique Shock Relations Derivation](https://i.ytimg.com/vi/JBZtFhXRkVM/mqdefault.jpg)

![Vortex Panel Method: Airfoil
The vortex panel method code in this video is an adaptation of the source panel method code from a few videos ago. The only change weve made between the codes is the formulation of the matrix system of equations (including the addition of the Kutta condition equation).
Well look at a few examples of the code working like you would expect, and compare resulting lift and moment coefficients to the XFOIL results. Then well look at a few cases where the code seems to fall apart, which is the motivation for my next two videos, the combined source/vortex panel method.
WHERE ARE WE GOING?
→ The limitations in this video motivate the need for a more robust implementation of the VPM.
→ I will derive the combined SPM/VPM formulation and code it to show how good we can get the results for a pretty simple implementation.
→ We can finally extend the SPM/VPM formulation to multiple separate airfoil elements. This will be the last video in the series.
CODE
► My website
http://www.joshtheengineer.com/2020/06/21/vortex-panel-method-airfoil/
► GitHub
https://github.com/jte0419/Panel_Methods
RELEVANT VIDEOS
► Panel Methods Playlist
https://www.youtube.com/watch?v=bWjo3N9COz4&list=PLxT-itJ3HGuUDVMuWKBxyoY8Dm9O9qstP
► Panel Method Geometry
https://www.youtube.com/watch?v=kIqxbd937PI
► Building More Complex Flows
https://www.youtube.com/watch?v=EKzbwJvKcmw
► Flow Around an Airfoil
https://www.youtube.com/watch?v=cLdv1UfX1g8
► Normal Velocity Geometric Integral [K(ij)]
https://www.youtube.com/watch?v=5lmIv2CUpoc
► Tangential Velocity Geometric Integral [L(ij)]
https://www.youtube.com/watch?v=IxWJzwIG_gY
► Streamline Geometric Integral VPM [Nx(ij) and Ny(ij)]
https://www.youtube.com/watch?v=TBwBnW87hso
► Solving the System of Equations: VPM
https://www.youtube.com/watch?v=j3ETHFBiYOg
► Source Panel Method: Airfoil
https://www.youtube.com/watch?v=fdNOYdwY9Bw
NOTES
→ Ill add notes here if I need to.
ERRORS
→ If you see an error in the video, please let me know and I will include it here.
REFERENCES
Note: the links are Amazon affiliate links. If you do happen to want to buy the book and use the link below, it helps me out a little.
► Fundamentals of Aerodynamics, Anderson
https://amzn.to/3emVuXU
► Foundations of Aerodynamics, Kuethe and Chow
https://amzn.to/2yMg1Vi
► Theory of Wing Sections, Abbott and Doenhoff
https://amzn.to/2wvZyUt Vortex Panel Method: Airfoil](https://i.ytimg.com/vi/JL2fz-xTTT0/mqdefault.jpg)
![Explained: Ghost Nodes [CFD]
In some finite difference/volume equations, you might need to use points that are outside of the actual grid domain. In these cases, ghost nodes can be calculated from the interior points and used for the differences (such as a central difference on a boundary node). Explained: Ghost Nodes [CFD]](https://i.ytimg.com/vi/JMP9aanQ5o0/mqdefault.jpg)
![Source Panel Method: Tangential Velocity Geometric Integral [J(ij)]
In the previous video (Geometric Integral Iij), we went through the full derivation of the geometric integral for the normal partial derivative, which was needed to solve for the source panel strengths. In this video, we will go through the (very similar) derivation of the tangential partial derivative geometric integral, which is needed to solve for the panel velocities, and thus the panel pressure coefficients.
This derivation is almost exactly the same as the normal geometric integral derivation, but there are some slight differences. Where it is exactly the same, I will refer you back to my other video (Iij) so we dont make this video longer than it needs to be.
RELEVANT VIDEOS
► Panel Methods Playlist
https://www.youtube.com/watch?v=bWjo3N9COz4&list=PLxT-itJ3HGuUDVMuWKBxyoY8Dm9O9qstP
► Panel Method Geometry
https://www.youtube.com/watch?v=kIqxbd937PI
► Building More Complex Flows
https://www.youtube.com/watch?v=EKzbwJvKcmw
► Flow Around an Airfoil
https://www.youtube.com/watch?v=cLdv1UfX1g8
► Normal Velocity Geometric Integral, Iij
https://www.youtube.com/watch?v=76vPudNET6U
NOTES
- Ill add notes here if I need to.
ERRORS
- If you see an error in the video, please let me know and I will include it here.
REFERENCES
Note: the links are Amazon affiliate links. If you do happen to want to buy the book and use the link below, it helps me out a little.
► Fundamentals of Aerodynamics, Anderson
https://amzn.to/3emVuXU
► Foundations of Aerodynamics, Kuethe and Chow
https://amzn.to/2yMg1Vi
► Theory of Wing Sections, Abbott and Doenhoff
https://amzn.to/2wvZyUt Source Panel Method: Tangential Velocity Geometric Integral [J(ij)]](https://i.ytimg.com/vi/JRHnOsueic8/mqdefault.jpg)

![Oblique Shock Example Problem
Lets work through an oblique shock (OS) example. In this video, we will go through four methods for solving OS problems.
1) Derived equations
2) Compressible flow tables (NACA 1135)
3) VT calculator
4) MATLAB functions
RELEVANT VIDEOS
→ Oblique Shock Derivation
https://goo.gl/xLYYYP
→ Normal Shock Relations Derivation
https://goo.gl/Unvjey
→ Normal Shock Example
https://goo.gl/RBJtgV
RELEVANT LINKS
► VT Calculator
http://www.dept.aoe.vt.edu/~devenpor/aoe3114/calc.html
► MATLAB Functions
https://github.com/jte0419/Compressible_Flow_Relations
THUMBNAIL CREDIT
By Settles1 (Own work) [CC BY-SA 4.0 (https://creativecommons.org/licenses/by-sa/4.0)], via Wikimedia Commons Oblique Shock Example Problem](https://i.ytimg.com/vi/JvrWmg8m5is/mqdefault.jpg)
![Explained: TI-83 Linear Interpolation Program [Math]
In this video I show you how to program a linear interpolation equation into your TI-83 graphing calculator.
If you would like to see how the equation is derived, click the link below to my other video.
https://goo.gl/7OA0UU
Here is the code if you already know how to input it into your calculator:
PROGRAM:INTERP
Input X1=,A
Input X2=,D
Input X= ,I
Input Y1=,N
Input Y2=,S
Disp (((S-N)/(D-A))(I-A)+N) Explained: TI-83 Linear Interpolation Program [Math]](https://i.ytimg.com/vi/KQzK5z9jkHE/mqdefault.jpg)