Uploaded February 2024 | Updated September 2026, 35 seconds ago
Lot's of stuff going on in Episode 285 of Mike Finnegan's Garage and this time we are fixing Blasphemi, moddying my 1961 Cadillac Coupe DeVille, and hopping up my garage. It's a super fun one! First up, we had a leaking head gasket on Blasphemi and rather than ripping the motor apart we did what most humans would do, we went to the auto parts store and bought a can of fix-it sauce. Oddly enough, it worked! Here's a link to it:
K Seal Head Gasket Repair: kseal.com/?gad_source=1&gclid=Cj0KCQiA5-uuBhDzARIsAAa21T_-EnHGjsrzQ6J703qJCWRfBe88nKJDu31Tq0I4whH-j0V45c3MO9waAmX-EALw_wcB
Next, we installed a new mid-plate behind the Nelson Racing Engines mockup big-block Chevy. Joe Cole built some trick brackets that I welded into the MRC Fab frame rails. Finally, we relocated the clutch switch on the clutch pedal to make it work better. I used my favorite machine to make that happen, the Miller Multimatic 220 AC/DC Multiprocess welder:
millerwelds.com/equipment/welders/multiprocess/multimatic-220-acdc-multiprocess-welder-m30190
Want more info on those trick configurable cabinets we put in the garage and in our new ATC Trailers Rom550 trailer? go here: atctrailers.com/products/rom-550
I was hoping to test Blasphemi here real soon but currently I'm physically unable to do it and we'll have to wait a bit until I heal up. If you'd like to know why I can't drive it, check out my next upload. It's an epic road trip with an unexpected ending. If you'd like to support this channel then please grab some of my new apparel at fsmgarage.com
Thanks for watching!
-Finnegan
Lot's of stuff going on in Episode 285 of Mike Finnegan's Garage and this time we are fixing Blasphemi, moddying my 1961 Cadillac Coupe DeVille, and hopping up my garage. It's a super fun one! First up, we had a leaking head gasket on Blasphemi and rather than ripping the motor apart we did what most humans would do, we went to the auto parts store and bought a can of fix-it sauce. Oddly enough, it worked! Here's a link to it:
K Seal Head Gasket Repair: kseal.com/?gad_source=1&gclid=Cj0KCQiA5-uuBhDzARIsAAa21T_-EnHGjsrzQ6J703qJCWRfBe88nKJDu31Tq0I4whH-j0V45c3MO9waAmX-EALw_wcB
Next, we installed a new mid-plate behind the Nelson Racing Engines mockup big-block Chevy. Joe Cole built some trick brackets that I welded into the MRC Fab frame rails. Finally, we relocated the clutch switch on the clutch pedal to make it work better. I used my favorite machine to make that happen, the Miller Multimatic 220 AC/DC Multiprocess welder:
millerwelds.com/equipment/welders/multiprocess/multimatic-220-acdc-multiprocess-welder-m30190
Want more info on those trick configurable cabinets we put in the garage and in our new ATC Trailers Rom550 trailer? go here: atctrailers.com/products/rom-550
I was hoping to test Blasphemi here real soon but currently I'm physically unable to do it and we'll have to wait a bit until I heal up. If you'd like to know why I can't drive it, check out my next upload. It's an epic road trip with an unexpected ending. If you'd like to support this channel then please grab some of my new apparel at fsmgarage.com
Thanks for watching!
-Finnegan
