Uploaded September 2021 | Updated November 2026, 2 days ago
This is a video tutorial explaining how to create a "Heart Transplant" Escape Room puzzle, using RF communication between two Arduinos.
One Arduino, placed inside a model heart, must be connected to a battery pack. This causes it to start beating, lighting up a programmable WS2812B Neopixel LED strip in a heartbeat animation, and also transmitting a regular "pulse" message from a 433MHz RF transmitter.
When this radio signal pulse is detected by a receiver module attached to a secondary Arduino contained within the ribcage of the skeleton, it causes a relay to be energised deactivating a maglock and releasing a key.
RF radio transmitter/receivers are not designed as proximity detectors, but by tuning the effective transmission range through a combination of hardware and software methods described, they can provide an interesting and useful alternative short-range detection method to more traditional magnet/RFID sensors used in escape rooms. The method described can be used to determine whether two powered devices are within a range of somewhere from 10cm up to a few metres in distance from each other, which makes it favourable for use in large-scale props compared to other sensors that require much more precise positioning.
Timings
---
00:00:00 - 00:02:22 Introduction and Demonstration
00:02:23 - 00:05:55 Overview of Puzzle Mechanics
00:05:56 - 00:11:23 RF Communication
00:11:24 - 00:15:38 Puzzle Hardware
00:15:39 - 00:22:09 Component Wiring
00:22:10 - 00:44:45 Arduino Code Listing
00:44:46 - 00:46:49 Wrapup
Hardware Used
---
- 433MHz RF Radio Receiver/Transmitter modules banggood.com/custlink/DGGEgOwcA0
- 5V relay module banggood.com/custlink/mDD3bOqeP5
- 2x Arduino Nano banggood.com/custlink/KvKDUmhTqI
- 12V 60kg Maglock ebay.co.uk/itm/164952553832
- WS2812B "Neopixel" LED strip banggood.com/custlink/3G3KMmYfzN
- 12V LED ring banggood.com/custlink/3m3E0O7W1R
- 3D Heart model thingiverse.com/thing:932606
- Bob the Skeleton is of unknown origin... would you believe, I found him in my closet! But he appears similar to this amazon.co.uk/Crazy-Bonez-POSE-N-STAY-Skelton-Halloween/dp/B01INAY2MA
If you enjoyed this video or found it helpful, please like and subscribe to this channel! And, if you'd like to download the Arduino code, wiring diagram, or other resources used in this and all the other escape room projects shown on this channel (and support me to continue making more tutorials in the future!), please check out my Patreon at patreon.com/playfultech
This is a video tutorial explaining how to create a "Heart Transplant" Escape Room puzzle, using RF communication between two Arduinos.
One Arduino, placed inside a model heart, must be connected to a battery pack. This causes it to start beating, lighting up a programmable WS2812B Neopixel LED strip in a heartbeat animation, and also transmitting a regular "pulse" message from a 433MHz RF transmitter.
When this radio signal pulse is detected by a receiver module attached to a secondary Arduino contained within the ribcage of the skeleton, it causes a relay to be energised deactivating a maglock and releasing a key.
RF radio transmitter/receivers are not designed as proximity detectors, but by tuning the effective transmission range through a combination of hardware and software methods described, they can provide an interesting and useful alternative short-range detection method to more traditional magnet/RFID sensors used in escape rooms. The method described can be used to determine whether two powered devices are within a range of somewhere from 10cm up to a few metres in distance from each other, which makes it favourable for use in large-scale props compared to other sensors that require much more precise positioning.
Timings
---
00:00:00 - 00:02:22 Introduction and Demonstration
00:02:23 - 00:05:55 Overview of Puzzle Mechanics
00:05:56 - 00:11:23 RF Communication
00:11:24 - 00:15:38 Puzzle Hardware
00:15:39 - 00:22:09 Component Wiring
00:22:10 - 00:44:45 Arduino Code Listing
00:44:46 - 00:46:49 Wrapup
Hardware Used
---
- 433MHz RF Radio Receiver/Transmitter modules banggood.com/custlink/DGGEgOwcA0
- 5V relay module banggood.com/custlink/mDD3bOqeP5
- 2x Arduino Nano banggood.com/custlink/KvKDUmhTqI
- 12V 60kg Maglock ebay.co.uk/itm/164952553832
- WS2812B "Neopixel" LED strip banggood.com/custlink/3G3KMmYfzN
- 12V LED ring banggood.com/custlink/3m3E0O7W1R
- 3D Heart model thingiverse.com/thing:932606
- Bob the Skeleton is of unknown origin... would you believe, I found him in my closet! But he appears similar to this amazon.co.uk/Crazy-Bonez-POSE-N-STAY-Skelton-Halloween/dp/B01INAY2MA
If you enjoyed this video or found it helpful, please like and subscribe to this channel! And, if you'd like to download the Arduino code, wiring diagram, or other resources used in this and all the other escape room projects shown on this channel (and support me to continue making more tutorials in the future!), please check out my Patreon at patreon.com/playfultech










