Uploaded September 2022 | Updated September 2026, 3 weeks ago
🇧🇬 Българска версия на клипа, тук: youtu.be/oybHSAkR0no
🇬🇧 𝗚𝗥𝗜𝗭𝗭𝗟𝗬 𝗦𝗲𝗿𝗶𝗲𝘀 𝗥𝗦 123 – 3 𝗶𝗻 1 𝗺𝗮𝗰𝗵𝗶𝗻𝗲
(KNIFE ROLLER, CAMBRIDGE ROLLER & CRIMPER ROLLER)
1️⃣ 𝗞𝗡𝗜𝗙𝗘 𝗥𝗢𝗟𝗟𝗘𝗥
The "𝗚𝗥𝗜𝗭𝗭𝗟𝗬" knife roller is intended for intensive grinding of post-harvest residue after corn and rapeseed as well as green mass of aftercrop plants.
The “𝗚𝗥𝗜𝗭𝗭𝗟𝗬” is especially good in the fight against the corn borer beetle that lives in corn stubble. By crushing the stubble, which is the beetle’s natural habitat, its chances of survival are greatly reduced.
The “𝗚𝗥𝗜𝗭𝗭𝗟𝗬” is most effective at speeds between 15 and 20 km/h. At this speed, “𝗚𝗥𝗜𝗭𝗭𝗟𝗬” can reach a capacity of up to 15 hectares/hour and thus far surpasses mower-type implements, which only work above ground and thus do not ensure the same degree of mulching.
Plant residues and stubble are cut into 10-15 cm lengths, crushed and pressed into the ground, which accelerates the activation of microorganisms and the degradation of plant residues.
One of the challenges in rapeseed stubble cultivation is not to bury the fine rapeseed too deep. If they are buried too deep, there is a risk that they will go into dormancy (seminal dormancy). In this condition, the rapeseed can germinate for several years. For this reason, it is essential to only work ultra-shallowly when cultivating rape stubble.
This is no longer a problem with the "𝗚𝗥𝗜𝗭𝗭𝗟𝗬" knife roller. Due to the special blade geometry, the blades do not penetrate deeper than 2 cm into the ground.
This gives you enough soil movement to stimulate the grains to germinate, to mix the organic material on the surface and, on the other hand, to save valuable soil water.
2️⃣ 𝗖𝗔𝗠𝗕𝗥𝗜𝗗𝗚𝗘 𝗥𝗢𝗟𝗟𝗘𝗥
The Cambridge rollers are well known universal machines to provide perfect soil contact, for example during seedbed preparation or when rolling fields of grain damaged by frost.
This construction of Cambridge rollers are available with Cambridge rings in two working widths from 10.5 m and 12.3 m.
3️⃣ 𝗖𝗥𝗜𝗠𝗣𝗘𝗥 𝗥𝗢𝗟𝗟𝗘𝗥
Roller-crimpers are perhaps the most important equipment for organic no-tillers to own, as they let growers terminate cover crops without chemicals and lay down thick mulch to smother weeds.
The advantages of crimpers are they kill cover crops mechanically, suppress weeds by forming a mulch, decrease hot summer soil temperatures, conserve soil moisture, decreases soil erosion, and add organic matter.
The blades are positioned and curved in a “chevron” pattern at a special angle to reduce bouncing, soil movement, and to increase maximum plant stem crimping pressure.
As the barrel rotates the pressure on the blades splits from the centre and moves outwards laying over and “crimping” vegetation, bruising the stalk of the plant and effectively stunting or shutting down the plant.
𝒮𝑒𝑒 𝓂𝑜𝓇𝑒 𝒽𝑒𝓇𝑒:
🌐 madaraagro.com/en/product/229/chopper-cutter-grizzly-foldable
🌐 madaraagro.com/en/product/37/roller-trailed-series-bk
#MADARAAgro, Madara Agro, #KNIFERoller, #Tractor, #Agricultural, #notill, #Bulgaria.
🇧🇬 Българска версия на клипа, тук: youtu.be/oybHSAkR0no
🇬🇧 𝗚𝗥𝗜𝗭𝗭𝗟𝗬 𝗦𝗲𝗿𝗶𝗲𝘀 𝗥𝗦 123 – 3 𝗶𝗻 1 𝗺𝗮𝗰𝗵𝗶𝗻𝗲
(KNIFE ROLLER, CAMBRIDGE ROLLER & CRIMPER ROLLER)
1️⃣ 𝗞𝗡𝗜𝗙𝗘 𝗥𝗢𝗟𝗟𝗘𝗥
The "𝗚𝗥𝗜𝗭𝗭𝗟𝗬" knife roller is intended for intensive grinding of post-harvest residue after corn and rapeseed as well as green mass of aftercrop plants.
The “𝗚𝗥𝗜𝗭𝗭𝗟𝗬” is especially good in the fight against the corn borer beetle that lives in corn stubble. By crushing the stubble, which is the beetle’s natural habitat, its chances of survival are greatly reduced.
The “𝗚𝗥𝗜𝗭𝗭𝗟𝗬” is most effective at speeds between 15 and 20 km/h. At this speed, “𝗚𝗥𝗜𝗭𝗭𝗟𝗬” can reach a capacity of up to 15 hectares/hour and thus far surpasses mower-type implements, which only work above ground and thus do not ensure the same degree of mulching.
Plant residues and stubble are cut into 10-15 cm lengths, crushed and pressed into the ground, which accelerates the activation of microorganisms and the degradation of plant residues.
One of the challenges in rapeseed stubble cultivation is not to bury the fine rapeseed too deep. If they are buried too deep, there is a risk that they will go into dormancy (seminal dormancy). In this condition, the rapeseed can germinate for several years. For this reason, it is essential to only work ultra-shallowly when cultivating rape stubble.
This is no longer a problem with the "𝗚𝗥𝗜𝗭𝗭𝗟𝗬" knife roller. Due to the special blade geometry, the blades do not penetrate deeper than 2 cm into the ground.
This gives you enough soil movement to stimulate the grains to germinate, to mix the organic material on the surface and, on the other hand, to save valuable soil water.
2️⃣ 𝗖𝗔𝗠𝗕𝗥𝗜𝗗𝗚𝗘 𝗥𝗢𝗟𝗟𝗘𝗥
The Cambridge rollers are well known universal machines to provide perfect soil contact, for example during seedbed preparation or when rolling fields of grain damaged by frost.
This construction of Cambridge rollers are available with Cambridge rings in two working widths from 10.5 m and 12.3 m.
3️⃣ 𝗖𝗥𝗜𝗠𝗣𝗘𝗥 𝗥𝗢𝗟𝗟𝗘𝗥
Roller-crimpers are perhaps the most important equipment for organic no-tillers to own, as they let growers terminate cover crops without chemicals and lay down thick mulch to smother weeds.
The advantages of crimpers are they kill cover crops mechanically, suppress weeds by forming a mulch, decrease hot summer soil temperatures, conserve soil moisture, decreases soil erosion, and add organic matter.
The blades are positioned and curved in a “chevron” pattern at a special angle to reduce bouncing, soil movement, and to increase maximum plant stem crimping pressure.
As the barrel rotates the pressure on the blades splits from the centre and moves outwards laying over and “crimping” vegetation, bruising the stalk of the plant and effectively stunting or shutting down the plant.
𝒮𝑒𝑒 𝓂𝑜𝓇𝑒 𝒽𝑒𝓇𝑒:
🌐 madaraagro.com/en/product/229/chopper-cutter-grizzly-foldable
🌐 madaraagro.com/en/product/37/roller-trailed-series-bk
#MADARAAgro, Madara Agro, #KNIFERoller, #Tractor, #Agricultural, #notill, #Bulgaria.



![GRIZZLY Series RS 🇧🇬
For English [🇬🇧] version: https://youtu.be/kmK0ZtY9ZdE
🇧🇬 ОПИСАНИЕ НА ВИДЕОТО ПО МИНУТИ:
00:00 - 12-метрова сечка SAVAGE Серия BIP 123
00:05 - Една универсална рама с възможност за три вида работни органи
00:21 - Работна скорост на сечката
00:26 - Теоретична производителност на сечката (150 декара за час)
00:31 - Работа в слънчоглед и рапица
00:39 - Други конструкции на сечки, които предлагаме
00:52 - Резултатите след сечката
01:02 - Контакти на фирмата
𝗚𝗥𝗜𝗭𝗭𝗟𝗬 𝗦𝗲𝗿𝗶𝗲𝘀 𝗥𝗦 123 – машина 3️⃣ в 1️⃣ :
(1️⃣ СЕЧКА, 2️⃣ ВАЛЯК и 3️⃣ НО-ТИЛ КРИМПЕР-ВАЛЯК)
1️⃣ СЕЧКА 𝗚𝗥𝗜𝗭𝗭𝗟𝗬
Сечката 𝗚𝗥𝗜𝗭𝗭𝗟𝗬 е машина предназначена за интензивно смилане на следжътвени остатъци от слънчоглед и рапица, както и при определени обстоятелства: за царевична или зелена маса от покривни култури.
Растителните остатъци от слънчоглед и рапица в стърнищата се нарязват на 10-15 cm дължина, натрошават се и се пресоват в земята, което ускорява активирането на микроорганизмите подобряващи разграждането им.
“𝗚𝗥𝗜𝗭𝗭𝗟𝗬” е особено добър инструмент в борбата срещу някои инсекти, защото раздробяването на растителните остатъци в стърнищата, които са естествено местообитание на тези вредители, значително намалява шансове им за оцеляване.
Сечките “𝗚𝗥𝗜𝗭𝗭𝗟𝗬” са най-ефективни при скорости между 15 и 20 км/ч., като при тази скорост „𝗚𝗥𝗜𝗭𝗭𝗟𝗬” може да достигнат капацитет до 150 декара за час! По този начин надминават производителността на приспособленията тип мулчер (косачка), които дори работят само над земята и осигуряват различна степен на мулчиране т.е. нашите сечки предлагат търсената, нито прекалено плитка, нито прекалено дълбока обработка.
Разяснителен пример: Едно от предизвикателствата при обработката на рапицата е семената им да не се заравят прекалено дълбоко. Ако са заровени твърде дълбоко, съществува риск да изпаднат в латентност (семенна латентност). В това състояние рапицата може да покълва в продължение на години. Поради тази причина е от съществено значение да се работи изключително плитко, когато се култивират стърнища от рапица.
Това вече не е проблем със сечките 𝗚𝗥𝗜𝗭𝗭𝗟𝗬, защото благодарение на специалната геометрия на ножовете, те не проникват по-дълбоко от 2 см в земята, осигурявайки достатъчно движение на почвата, за стимулация на покълване на зърната, да се смеси органичният материал само на повърхността и същевременно, да се спести ценната почвена влага.
2️⃣ ВАЛЯК 𝗖𝗢𝗡𝗗𝗢𝗥
Когато сечащите възли на универсалната рама са заменени с ротори от тежести (отливки) тип 𝗖𝗔𝗠𝗕𝗥𝗜𝗗𝗚𝗘, сечката се превръща в притъпкващ валяк. Според нашите търговци, за Ваше улеснение Сечката 𝗚𝗥𝗜𝗭𝗭𝗟𝗬 автоматично придобива ново търговско наименование: 𝗖𝗢𝗡𝗗𝗢𝗥.
Валяците 𝗖𝗢𝗡𝗗𝗢𝗥 са добре познати универсални машини за осигуряване на перфектно уплътнение почвата, например за подготовка на сеитбено легло или за валиране на полета със зърно, увредени през зимните студове.
Тази конструкция на валяците 𝗖𝗢𝗡𝗗𝗢𝗥 се предлага с тежести (пръстени) тип Cambridge в две работни ширини от 10,5 m и 12,3 m.
3️⃣ НО-ТИЛ КРИМПЕР-ВАЛЯК
(𝗖𝗥𝗜𝗠𝗣𝗘𝗥 𝗥𝗢𝗟𝗟𝗘𝗥)
КРИМПЕР-ВАЛЯЦИТЕ са може би най-важното оборудване, което трябва да притежават хората насочили се към работа без конвенционални обработки (НО-ТИЛ, без оран), тъй като те им позволяват да унищожат механично покривните култури без химикали, превръщайки ги в слой дебел мулч, задушащ плевелите. Така също се намалява влиянието на горещите летни температури върху почвата, запазва се почвената влага, намалява се ерозията и се добавя ценна органична материя в най-ценната част на почвените слоеве.
За разлика от стандартните ни сечки, чийто напречно сечение е правилен многоъгълник, позволяващ ротация с интензивни, разсичащи, ударни натоварвания, тук остриетата (притъпкващите работни шини) са разположени в извита шевронна (V-образна) форма под специален ъгъл, за да намалят подскачането и нежеланите размествания на почва, както и да увеличат максималния равномерен натиск над стъблото на растенията.
For 🇬🇧 click here: https://fb.watch/fYauwS_fDi/
𝒮𝑒𝑒 𝓂𝑜𝓇𝑒 𝒽𝑒𝓇𝑒:
🌐 https://www.madaraagro.com/bg/product/228/razdrobitel-sechka-grizzly-sgavaem/
🌐 https://www.madaraagro.com/bg/product/23/kombiniran-valiak-prikachien-sieriia-bk/
#MADARAAgro, Madara Agro , #KNIFERoller, #Tractor, #Agricultural, #notill, #Bulgaria. GRIZZLY Series RS 🇧🇬](https://i.ytimg.com/vi/oybHSAkR0no/mqdefault.jpg)
![DUNAV Series RNT 🇧🇬
🇧🇬 𝗗𝗨𝗡𝗔𝗩 𝗦𝗲𝗿𝗶𝗲𝘀 𝗥𝗡𝗧 17𝗧:
🇬🇧 - YouTube version here: https://youtu.be/JyZC2OYr0o0
🇷🇴 - Varianta in romana aici: https://youtu.be/fKCNBtIKNgA
🇭🇷 - Hrvatska verzija ovdje: https://youtu.be/eRgP5La337Q
🇩🇪 - Deutsche Version hier: https://youtu.be/LtHkNgMC_1s
3-странно саморазтоварващо се, 16,5-кубиково, тандемно, ремарке за насипни товари.
Видеото по минути:
00:00 - Интро
00:15 - Маневреност на заден ход
00:28 - Поглед под ремаркето
00:42 - Размери на товарното пространство
01:05 - Окачване (ADR GROUP [ 🇮🇹 ]) и спирачна система (WABCO [ 🇦🇹 ])
01:22 - Данни за теглича ( ф40mm, Scharmüller [ 🇦🇹 ])
01:26 - 17 тонен хидравличен крик - (AGRIEST [ 🇫🇷 ])
01:37 - Инструкция за разтоварване назад
01:50 - Телескопични цилиндри - (C.U.S. Hydraulics S.r.l. [ 🇮🇹 ])
01:54 - Площадка за обслужване и канати - Archus Neumeier [ 🇦🇹 ]
02:01 - Инструкция за странично разтоварване
02:25 - Контакти
⚙️ ТЕХНИЧЕСКИ ДАННИ:
🔳Полезен обем [㎥]: 16,5
🔲Пълна маса [kg]: 17 780 (предлага се и в 14t. и 19t. варианти)
◽️ Товароносимост [kg]: 13 000
⬇️ Височина на товарното пространство от земята [m]: 1,35
🔳Размери на товарното пространство:
↕️ височина (канати) [m]: 0,6 / 0,8
↔️ широчина [m]: 2,30
↗️ дължина [m]: 5,05
СТАНДАРТНА ЕКИПИРОВКА:
✅Окачване: тандемно - ADR GROUP [ 🇮🇹 ]
✅Tеглич с ухо: Ф40 mm - Scharmüller GmbH & Co KG [ 🇦🇹 ]
✅Разтоварване: тристранно с два телескопични цилиндъра: C.U.S. Hydraulics S.r.l. [ 🇮🇹 ]
✅Спирачна система:
🛡 Раборна: двукръгова, пневатична - WABCO [ 🇦🇹 ]
🛡 Паркова: механична, ръчна
✅17 тонен хидравличен крик - AGRIEST [ 🇫🇷 ]
✅Площадка за обслужване
- Archus Neumeier GmbH & Co. KG [ 🇦🇹 ]
✅Канати и заключващи компоненти - Archus Neumeier [ 🇦🇹 ]
✅Гуми*: 385 / 65 – 22,5” - BKT Tires [ 🇮🇳 / 🇮🇹 ]
✅Джанти: 11,75 x 22,5” - Pronar Wheels [ 🇮🇩 ]
ℹ️ ОПЦИИ:
- заден шнек: CanAGRO GmbH [ 🇩🇪 ] (с хидромотор) за зареждане на сеялки и торачки
- заден шибър и улей за запълване на чували
- резервна гума и механизъм с лебедка
- решетъчна надстройка за превоз на силаж
- спирачни клинове
- кутия за инструменти - СФК ТРАК ООД [ 🇧🇬 ]
- заден теглич, хидравлична и електрическа система за допълнително ремарке
- покривало и механизъм за навиване
- гуми и джанти по специални изисквания на клиента*
🌐 https://www.madaraagro.com/en/product/58/hopper-bulk-loads-series-rnt/ DUNAV Series RNT 🇧🇬](https://i.ytimg.com/vi/pJvr2YpEllw/mqdefault.jpg)
![SAVAGE Series BIP 150 🇧🇬
🇬🇧 version here: https://youtu.be/WAmdwFetzVQ
🇷🇴 version here: https://youtu.be/bFiY0FVYENQ
🇩🇪 https://youtu.be/igtJ4MWcHQc
🇧🇬 ОПИСАНИЕ НА ВИДЕОТО ПО МИНУТИ:
00:00 - Въведение
00:12 - Транспортно положение
00:22 - Интензивно смесване на растителните остатъци
00:35 - Подходяща за заравяне и смесване на торта в почвата
00:42 - Използване като пролетен култиватор
01:00 - Работна скорост - 15 - 25 км/ч [до 250 декара/час]
01:17 - Кадри от различни почвени условия
01:38 - Контакти SAVAGE Series BIP 150 🇧🇬](https://i.ytimg.com/vi/pipLYRiU814/mqdefault.jpg)




