Uploaded October 2026 | Updated November 2026, 5 hours ago
GE top load washer won't drain or spin? Here's how I fixed a GE washer that won't drain by replacing the drain pump (model GTW220ACK3WW).
If your washer is full of water and the drain pump just hums, a jammed drain pump is a likely cause, and you can replace it yourself.
The lid lock engaged and the pump made a faint hum, so the lock was good and the pump was getting voltage. That was enough for me to skip meter readings at the pump and the control board. The tub can hold 8 to 26 gallons, so I emptied it with a 5-gallon shop vac first, then tipped the washer back. I took out the pump (three 3/8" hex screws), found the impeller jammed with sand, put in a new pump, checked for leaks, and tested it in service mode.
โฑ๏ธ Chapters
0:00 Washer won't drain or spin (GE GTW220ACK3WW)
0:12 Diagnosis: lid lock engages, pump hums
0:34 Getting the water out (shop vac)
1:32 Unplug, slide out, and tip the washer back
1:58 Tools, and catching leftover water
2:16 Remove the spring clamp and drain hose
2:39 Remove the drain pump (three 3/8" screws)
3:04 Inspect the impeller: it's jammed
3:32 Belt guard, quick connector, and zip tie
4:05 Sand found in the old pump
4:15 Install the new drain pump
4:31 Hose clamp pliers tip for the spring clamps
5:04 Leak test with the washer tipped back
5:27 Service mode test: draining again
๐ GE top load washer service mode & manuals: davespates.com/post/ge-top-load-washer-service-mode-and-manuals
๐ง Tools and Parts Used
โข Hose clamp pliers: amzn.to/4yr8LGJ
โข (Optional, shown on camera, no link) Replacement drain pump for your model, a 5-gallon shop vac, a 3/8" nut driver, pliers or needle nose, and a small bucket
๐บ Related videos
โข GE Top Load Washer Service Mode and Basic Troubleshooting: youtu.be/6f3ojJbmmuk
โข GE Washer Won't Drain - Rinse Light Blinking: youtu.be/IVhBKGLkZ4c
โข GE Top Load Washer Spins, then Stops after 5 Seconds: youtu.be/oGQK1myHpeI
๐ Playlists
โข Washer and Dryer Troubleshooting and Repairs: youtube.com/playlist?list=PLnX0gdC_NeAP45zUE8VcBoGvdRHiHJHiT
โข Appliance Repairs and Troubleshooting: youtube.com/playlist?list=PLnX0gdC_NeAP8DdRXkGjDtYXR7zaHDp7u
WARNING! This video is for educational purposes only. DIY repairs carry real risk. Turn off the power, water, or gas before working. Electrical, gas, and refrigerant work may require a licensed professional and permits under your local code. Renters, check your lease and contact your landlord before making any repairs. Dave and Apartment Maintenance Pro are not liable for any damage or injury.
Some links above are affiliate links, so if you buy through them I may earn a small commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
GE top load washer won't drain or spin? Here's how I fixed a GE washer that won't drain by replacing the drain pump (model GTW220ACK3WW).
If your washer is full of water and the drain pump just hums, a jammed drain pump is a likely cause, and you can replace it yourself.
The lid lock engaged and the pump made a faint hum, so the lock was good and the pump was getting voltage. That was enough for me to skip meter readings at the pump and the control board. The tub can hold 8 to 26 gallons, so I emptied it with a 5-gallon shop vac first, then tipped the washer back. I took out the pump (three 3/8" hex screws), found the impeller jammed with sand, put in a new pump, checked for leaks, and tested it in service mode.
โฑ๏ธ Chapters
0:00 Washer won't drain or spin (GE GTW220ACK3WW)
0:12 Diagnosis: lid lock engages, pump hums
0:34 Getting the water out (shop vac)
1:32 Unplug, slide out, and tip the washer back
1:58 Tools, and catching leftover water
2:16 Remove the spring clamp and drain hose
2:39 Remove the drain pump (three 3/8" screws)
3:04 Inspect the impeller: it's jammed
3:32 Belt guard, quick connector, and zip tie
4:05 Sand found in the old pump
4:15 Install the new drain pump
4:31 Hose clamp pliers tip for the spring clamps
5:04 Leak test with the washer tipped back
5:27 Service mode test: draining again
๐ GE top load washer service mode & manuals: davespates.com/post/ge-top-load-washer-service-mode-and-manuals
๐ง Tools and Parts Used
โข Hose clamp pliers: amzn.to/4yr8LGJ
โข (Optional, shown on camera, no link) Replacement drain pump for your model, a 5-gallon shop vac, a 3/8" nut driver, pliers or needle nose, and a small bucket
๐บ Related videos
โข GE Top Load Washer Service Mode and Basic Troubleshooting: youtu.be/6f3ojJbmmuk
โข GE Washer Won't Drain - Rinse Light Blinking: youtu.be/IVhBKGLkZ4c
โข GE Top Load Washer Spins, then Stops after 5 Seconds: youtu.be/oGQK1myHpeI
๐ Playlists
โข Washer and Dryer Troubleshooting and Repairs: youtube.com/playlist?list=PLnX0gdC_NeAP45zUE8VcBoGvdRHiHJHiT
โข Appliance Repairs and Troubleshooting: youtube.com/playlist?list=PLnX0gdC_NeAP8DdRXkGjDtYXR7zaHDp7u
WARNING! This video is for educational purposes only. DIY repairs carry real risk. Turn off the power, water, or gas before working. Electrical, gas, and refrigerant work may require a licensed professional and permits under your local code. Renters, check your lease and contact your landlord before making any repairs. Dave and Apartment Maintenance Pro are not liable for any damage or injury.
Some links above are affiliate links, so if you buy through them I may earn a small commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.










