Uploaded March 2025 | Updated September 2026, 6 hours ago
Haotian Laser
https://haotianlaser.store
The Links below are my Amazon Affiliate Links. By using the links below you are helping support this channel. Thank You!
Wixey Digital Angle Gauge
amzn.to/4iwZTYp
Engineering Square
amzn.to/3FywwH2
00:00 - Start
00:16 - The Basic of using a Rotary
04:05 - Get Started in LightBurn
07:29 - Basic Chuck Rotary Settings in LightBurn
10:06 - Installing the Rotary and set alignment
12:51 - Leveling the Tumbler
15:56 - Set Focus
17:00 - Finalize Design in LightBurn
18:15 - Preview Modes
20:24 - Split Size Entry
22:27 - Testing the steps per rotation in LIghtBurn
23:50 - Time to Engrave the Tumbler
This guide provides a step-by-step process for setting up a rotary on a galvo laser engraver, covering necessary tools, alignment techniques, and software settings to ensure accurate engraving results.
In this guide, we will explore the process of setting up a rotary on a galvo laser engraver. Whether you are using a CO2, fiber, or UV laser, the steps outlined here will help you achieve accurate and professional results. This tutorial is designed to be straightforward, providing a solid foundation for beginners and experienced users alike.
## Tools and Materials Needed
Before we begin, gather the following tools and materials:
- A 12 oz Koozie (or similar item to engrave)
- Blue painters tape
- An engineering square with a flat bottom
- A black Sharpie marker
- A Wixie digital angle gauge (highly recommended for accuracy)
## Step 1: Preparing the Koozie
1. **Apply Blue Painters Tape**: Start by wrapping a piece of blue painters tape around the Koozie. This will serve as a surface for marking.
2. **Mark a Vertical Line**: Use the engineering square to ensure that the line you draw with the Sharpie is perpendicular to the bottom and top of the Koozie. This line will help you align your engraving later.
3. **Measure the Diameter**: Measure the diameter of the Koozie, as this will be needed for the engraving software later.
## Step 2: Setting Up LightBurn
1. **Open LightBurn**: Launch the LightBurn software on your computer. You do not need to connect your rotary to the laser at this point.
2. **Draw a Line**: Use the pencil tool to draw a horizontal line in the software. Hold down the shift key to ensure the line is straight.
3. **Center the Line**: Select the line and press the "P" key to center it on the design grid. This line will be used to align with the Koozie.
Step 3: Aligning the Rotary
1. **Connect the Laser**: Once the line is drawn, connect your laser to LightBurn. Ensure the rotary is unplugged from the laser to allow free movement.
2. **Frame the Line**: Select the line you created and hit the frame button. This will project the line onto the laser bed.
3. **Align the Koozie**: Place the Koozie in the rotary and adjust it so that the black line you drew on the Koozie aligns with the projected red line from the laser. Secure the rotary once aligned.
Step 4: Leveling the Koozie
1. **Use the Wixie Gauge**: Place the Wixie digital angle gauge on top of the Koozie. Adjust the rotary until the gauge reads zero, ensuring that the Koozie is level with the laser head.
2. **Focus the Laser**: Use a predetermined focus stick to adjust the laser head to the correct height for engraving.
Step 5: Finalizing Settings in LightBurn
1. **Input Rotary Settings**: In LightBurn, go to the rotary setup tool. Select the Chuck type rotary and enable the rotary switch. Set the steps per rotation according to your rotary's specifications (e.g., 12,800 steps).
2. **Set Engraving Parameters**: Input the diameter of the Koozie to calculate the circumference. Adjust the engraving speed, frequency, and other settings as needed.
3. **Test the Setup**: Use the test feature in LightBurn to confirm that the rotary settings are correct. The rotary should make one full revolution and return to the starting point.
Step 6: Engraving the Design
1. **Select the Design**: Import your logo or design into LightBurn and ensure it fits within the engraving area.
2. **Frame the Design**: Frame the design to see how it will appear on the Koozie. Adjust as necessary to ensure proper placement.
3. **Start Engraving**: Once everything is set, start the engraving process. Monitor the engraving to ensure quality results.
Conclusion
Setting up a rotary on a galvo laser engraver involves careful preparation and alignment to achieve the best results. By following these steps, you can ensure that your engravings are precise and professional. Remember to adjust your settings based on the material and design for optimal outcomes. Happy engraving!
Haotian Laser
https://haotianlaser.store
The Links below are my Amazon Affiliate Links. By using the links below you are helping support this channel. Thank You!
Wixey Digital Angle Gauge
amzn.to/4iwZTYp
Engineering Square
amzn.to/3FywwH2
00:00 - Start
00:16 - The Basic of using a Rotary
04:05 - Get Started in LightBurn
07:29 - Basic Chuck Rotary Settings in LightBurn
10:06 - Installing the Rotary and set alignment
12:51 - Leveling the Tumbler
15:56 - Set Focus
17:00 - Finalize Design in LightBurn
18:15 - Preview Modes
20:24 - Split Size Entry
22:27 - Testing the steps per rotation in LIghtBurn
23:50 - Time to Engrave the Tumbler
This guide provides a step-by-step process for setting up a rotary on a galvo laser engraver, covering necessary tools, alignment techniques, and software settings to ensure accurate engraving results.
In this guide, we will explore the process of setting up a rotary on a galvo laser engraver. Whether you are using a CO2, fiber, or UV laser, the steps outlined here will help you achieve accurate and professional results. This tutorial is designed to be straightforward, providing a solid foundation for beginners and experienced users alike.
## Tools and Materials Needed
Before we begin, gather the following tools and materials:
- A 12 oz Koozie (or similar item to engrave)
- Blue painters tape
- An engineering square with a flat bottom
- A black Sharpie marker
- A Wixie digital angle gauge (highly recommended for accuracy)
## Step 1: Preparing the Koozie
1. **Apply Blue Painters Tape**: Start by wrapping a piece of blue painters tape around the Koozie. This will serve as a surface for marking.
2. **Mark a Vertical Line**: Use the engineering square to ensure that the line you draw with the Sharpie is perpendicular to the bottom and top of the Koozie. This line will help you align your engraving later.
3. **Measure the Diameter**: Measure the diameter of the Koozie, as this will be needed for the engraving software later.
## Step 2: Setting Up LightBurn
1. **Open LightBurn**: Launch the LightBurn software on your computer. You do not need to connect your rotary to the laser at this point.
2. **Draw a Line**: Use the pencil tool to draw a horizontal line in the software. Hold down the shift key to ensure the line is straight.
3. **Center the Line**: Select the line and press the "P" key to center it on the design grid. This line will be used to align with the Koozie.
Step 3: Aligning the Rotary
1. **Connect the Laser**: Once the line is drawn, connect your laser to LightBurn. Ensure the rotary is unplugged from the laser to allow free movement.
2. **Frame the Line**: Select the line you created and hit the frame button. This will project the line onto the laser bed.
3. **Align the Koozie**: Place the Koozie in the rotary and adjust it so that the black line you drew on the Koozie aligns with the projected red line from the laser. Secure the rotary once aligned.
Step 4: Leveling the Koozie
1. **Use the Wixie Gauge**: Place the Wixie digital angle gauge on top of the Koozie. Adjust the rotary until the gauge reads zero, ensuring that the Koozie is level with the laser head.
2. **Focus the Laser**: Use a predetermined focus stick to adjust the laser head to the correct height for engraving.
Step 5: Finalizing Settings in LightBurn
1. **Input Rotary Settings**: In LightBurn, go to the rotary setup tool. Select the Chuck type rotary and enable the rotary switch. Set the steps per rotation according to your rotary's specifications (e.g., 12,800 steps).
2. **Set Engraving Parameters**: Input the diameter of the Koozie to calculate the circumference. Adjust the engraving speed, frequency, and other settings as needed.
3. **Test the Setup**: Use the test feature in LightBurn to confirm that the rotary settings are correct. The rotary should make one full revolution and return to the starting point.
Step 6: Engraving the Design
1. **Select the Design**: Import your logo or design into LightBurn and ensure it fits within the engraving area.
2. **Frame the Design**: Frame the design to see how it will appear on the Koozie. Adjust as necessary to ensure proper placement.
3. **Start Engraving**: Once everything is set, start the engraving process. Monitor the engraving to ensure quality results.
Conclusion
Setting up a rotary on a galvo laser engraver involves careful preparation and alignment to achieve the best results. By following these steps, you can ensure that your engravings are precise and professional. Remember to adjust your settings based on the material and design for optimal outcomes. Happy engraving!
