Uploaded January 2017 | Updated November 2026, 3 hours ago
A short demonstration on using the FreeCAD sweep tool from the parts workbench. I demonstrate how to use the tool on Draft, Sketch and Parametric Geometries.
I show a little how to use a sweep path multiple times and how to change the junctions.
A short demonstration on using the FreeCAD sweep tool from the parts workbench. I demonstrate how to use the tool on Draft, Sketch and Parametric Geometries.
I show a little how to use a sweep path multiple times and how to change the junctions.






![OpenSCAD - BASICS - Make-a-Module Keyhole mount opening
This is a module I thought might be useful to keep in a library, possibly not, it was rewarding doing it anyway. It is very basic stuff here. Dont bother if you have experience. You have been warned.
Here is a step by step with time index. ( I got out of sync around step 10. )
STEP1.) 00:53 Create the Module and add Variables
module keyhole_mount( thickness ){
SCREW_DIAMETER = 3; // The shaft of the bolt
SCREW_HEAD_DIAMETER = 6; // The head of the bolt
}
STEP 2.) 01:38 Add a call to the module so we can render as we go.
keyhole_mount( 2 );
STEP 3.) 02:01 Add 2 - 2D Circles and a hull for the basic cutout.
circle(SCREW_DIAMETER/2, center=true);
circle(SCREW_DIAMETER/2, center=true);
STEP 4.) 02:56 Translate the second circle using the screw head diameter as the distance
translate([SCREW_HEAD_DIAMETER,0])
STEP 5.) 02:56 Create a hull() of the two circles
hull(){
circle(SCREW_DIAMETER/2);
translate([SCREW_HEAD_DIAMETER,0]) circle(SCREW_DIAMETER/2, center=true);
}
STEP 6.) 03:42 Add a third circle for the screw head to fit through.
circle(SCREW_HEAD_DIAMETER/2);
STEP 7.) 04:20 Translate the third circle using the screw head diameter as the distance
translate([SCREW_HEAD_DIAMETER,0])
STEP 8.) 04:40 Add thickness using linear_extrude and the thickness arguement, we use the full thickness to avoid overlaping faces.
linear_extrude( thickness ) {
}
STEP 9.) 05:23 translate this object in the negative Z direcection so the bottom face does not overlap with the cutouts bottom face.
LABEL THIS SECTION AS THE Keyhole Cutout
BELOW THE KEYHOLE CUTOUT add code for the DETENT
LABEL THIS SECTION THE DETENT
STEP 10. ) 06:00 Copy the hull() portion in STEP 5 and change SCREW_DIAMETER to SCREW_HEAD_DIAMETER
hull(){
circle( SCREW_HEAD_DIAMETER/2 + SCREW_HEAD_DIAMETER/8 );
translate([SCREW_HEAD_DIAMETER,0]) circle( SCREW_HEAD_DIAMETER/2 + SCREW_HEAD_DIAMETER/8);
}
STEP 11. ) Add thickness to the detent using the thickness arguement. Use the full thickness to ensure it is properly subtracted later in the model.
linear_extrude( thickness/2 ) {
}
STEP 12.) 06:45 Translate the detent in the positive Z direction half the amount of thickness.
translate( [0,0,thickness/2] ){
STEP 13.) 08:10 Make a union() out of these shapes
STEP 14. ) 08:20 Create a test shape to cutout a keyhole
STEP 15.) Position the shape with translate
STEP 16.) 09:30 make multiple copies with linear_array module() OpenSCAD - BASICS - Make-a-Module Keyhole mount opening](https://i.ytimg.com/vi/JKZV9bXuVQk/mqdefault.jpg)



