Uploaded October 2018 | Updated November 2026, 11 hours ago
The appeal of fluorination as a technique for the removal of uranium from fluoride fuel salt has been noted for many years and fluorination formed an integral part of most of the chemical processing flowsheets that were developed at Oak Ridge National Laboratory under the Molten-Salt Reactor Program from 1957 to 1976. Fluorinators were envisioned at a variety of locations in the chemical processing, universally under the assumption that they would remove uranium from the fuel salt. Despite the prevalence of fluorination as an envisioned chemical processing technique, the actual amount of development that was undertaken on continuous fluorination was surprisingly small.
Batch fluorination was utilized to remove uranium from the fuel salt of the Molten-Salt Reactor Experiment (MSRE) in 1968, but this was done in the drain tank of the reactor vessel and led to the introduction of a significant amount of corrosion products. Repeated fluorination of the MSRE fuel salt in this manner would have undoubtedly led to the structural failure of the drain tank due to corrosion.
But the aggressiveness of F2 led to many practical engineering challenges in the development of a continuous fluorination system. To protect the fluorinator from F2 attack, ORNL engineers envisioned using an extensive interior cooling system to freeze a layer of salt on the fluorination column’s inner surface. A fuel salt containing fresh fission products has considerable internal heat generation that can be opposed by a cooling system to form a frozen wall on the interior surface of a fluorination column. But a chemically-similar simulant salt, such as LiF-BeF2-UF4, where fission products are replaced with stable isotopes, has no such internal heat generation term. It was necessary to simultaneously heat the salt internally, to simulate the heating effect of fission product decay, while cooling the wall of the fluorinator to generate the frozen wall. Thus testing the frozen wall of the fluorinator under these conditions was very difficult. This was never satisfactorily resolved during the Molten-Salt Reactor Project.
In the years since the MSRE concluded in 1976, alternative fluorination agents have been advanced for consideration. Most notable among these is NF3. NF3 has been considered for rocket propulsion and is extensively used in the electronics industry to clean and etch microelectronic silica chips. It is minimally hazardous and not corrosive at temperatures below 70C and is likely less corrosive than other fluorinating agents. It is not known to react with moisture, is thermally stable at room temperature, and has been demonstrated by PNNL to be an effective, thermallytunable fluorination/oxidation agent for spent nuclear fuel constituents. By controlling the treatment temperature, NF3 will selectively fluorinate/oxidize spent nuclear fuel constituents. The different temperature sensitivities and NF3 concentration effects for the fluorination/oxidation of the different constituents potentially provides mechanisms to effect separations of the volatile fluorides.
The hazard level, and chemical reactivity attributes potentially make NF3 a very attractive fluorinating/oxidizing agent for managing the composition of the fuel salt in a liquid-fluoride reactor where uranium is the dominant or even exclusive fissile material. Fluorination/oxidation of the fuel salt with NF3 would produce UF6 and remove uranium from the salt. Reductive extraction could then be employed to remove non-volatile fission and activation products from the salt. Hydrogen could be used to reduce UF6 back to UF4 and reconstitute the salt for return to the reactor.
Flibe-Energy.com
The appeal of fluorination as a technique for the removal of uranium from fluoride fuel salt has been noted for many years and fluorination formed an integral part of most of the chemical processing flowsheets that were developed at Oak Ridge National Laboratory under the Molten-Salt Reactor Program from 1957 to 1976. Fluorinators were envisioned at a variety of locations in the chemical processing, universally under the assumption that they would remove uranium from the fuel salt. Despite the prevalence of fluorination as an envisioned chemical processing technique, the actual amount of development that was undertaken on continuous fluorination was surprisingly small.
Batch fluorination was utilized to remove uranium from the fuel salt of the Molten-Salt Reactor Experiment (MSRE) in 1968, but this was done in the drain tank of the reactor vessel and led to the introduction of a significant amount of corrosion products. Repeated fluorination of the MSRE fuel salt in this manner would have undoubtedly led to the structural failure of the drain tank due to corrosion.
But the aggressiveness of F2 led to many practical engineering challenges in the development of a continuous fluorination system. To protect the fluorinator from F2 attack, ORNL engineers envisioned using an extensive interior cooling system to freeze a layer of salt on the fluorination column’s inner surface. A fuel salt containing fresh fission products has considerable internal heat generation that can be opposed by a cooling system to form a frozen wall on the interior surface of a fluorination column. But a chemically-similar simulant salt, such as LiF-BeF2-UF4, where fission products are replaced with stable isotopes, has no such internal heat generation term. It was necessary to simultaneously heat the salt internally, to simulate the heating effect of fission product decay, while cooling the wall of the fluorinator to generate the frozen wall. Thus testing the frozen wall of the fluorinator under these conditions was very difficult. This was never satisfactorily resolved during the Molten-Salt Reactor Project.
In the years since the MSRE concluded in 1976, alternative fluorination agents have been advanced for consideration. Most notable among these is NF3. NF3 has been considered for rocket propulsion and is extensively used in the electronics industry to clean and etch microelectronic silica chips. It is minimally hazardous and not corrosive at temperatures below 70C and is likely less corrosive than other fluorinating agents. It is not known to react with moisture, is thermally stable at room temperature, and has been demonstrated by PNNL to be an effective, thermallytunable fluorination/oxidation agent for spent nuclear fuel constituents. By controlling the treatment temperature, NF3 will selectively fluorinate/oxidize spent nuclear fuel constituents. The different temperature sensitivities and NF3 concentration effects for the fluorination/oxidation of the different constituents potentially provides mechanisms to effect separations of the volatile fluorides.
The hazard level, and chemical reactivity attributes potentially make NF3 a very attractive fluorinating/oxidizing agent for managing the composition of the fuel salt in a liquid-fluoride reactor where uranium is the dominant or even exclusive fissile material. Fluorination/oxidation of the fuel salt with NF3 would produce UF6 and remove uranium from the salt. Reductive extraction could then be employed to remove non-volatile fission and activation products from the salt. Hydrogen could be used to reduce UF6 back to UF4 and reconstitute the salt for return to the reactor.
Flibe-Energy.com

![SINAP T-MSR Promotional Video [ Thorium Molten Salt Reactor ] [ Captioned in English ]
Chinas Thorium-MSR (Molten Salt Reactor) program has created a promotional video.
Conrad Knauer found this on http://wemedia.ifeng.com and shared on Twitter: https://twitter.com/ConradKnauer/status/1030373450324443138
Some translated excerpts:
Of the 6 types of fourth generation atomic reactors the type that combines both atmospheric pressure and high temperature is the molten salt reactor including both liquid fuel and solid fuel types.
The liquid fuel type molten salt reactor incorporates online reprocessing to maximize the fuel utilization of the thorium cycle.
The solid fuel molten salt reactor can achieve higher temperature to maximize efficiency of combined heat and power generation applications.
Thorium based molten salt reactors can be used in inland water-scarce areas and can allow us to use the vast resources of Northwest China to achieve energy and resource independence.
In 2011, to advance the development requirements of our nation The Chinese Academy of Sciences commenced The Near future disruptive change atomic energy - Thorium molten salt reactor apparatus strategic pilot science and technology project, with political power behind the molten salt reactor research.
In the past 5 years, the development of key systems and techniques have made vital advancements Specialized developments established the software analysis system required to study the molten salt reactor and grasped the thorium molten salt reactor design analysis technique completed the worlds first experimental solid fuel molten salt reactor engineering design with national and international co-operation we have formulated a safety standard for thorium molten salt reactors as well as anti-proliferation and safety classification documentation.
Specific breakthroughs have occurred in the molten salt reactor itself and techniques in many crucial areas related to the molten salt reactor loop successfully research and developing molten salt pumps, molten salt heat exchanges, high-temperature instrumentation and controls, etc.
The project establishes an all-new online separation process combined with a dry method of reprocessing that simultaneously realizes the online dry reprocessing, pioneering isotopic solvent extraction and centrifugal separation.
In a world first, the technologys cascade separation and batch preparation. puts fluoride salt preparation and purification within grasp, allowing production in the scale of tons.
THANKS to Mon Malthias, Meese Engine and Conrad Knauer for their contributions to Community Captioning in English! SINAP T-MSR Promotional Video [ Thorium Molten Salt Reactor ] [ Captioned in English ]](https://i.ytimg.com/vi/EdelSZUxZeM/mqdefault.jpg)






![THORIUM DEBUNK
Thorium, element 90 on the periodic table, is a fertile material. When struck by a neutron, it will change (over time) into Uranium-233. Uranium-233 is fissile, and can fission into energy and fission products.
Claims have been made regarding both thoriums energy potential, and counter claims that it holds no particular advantage over uranium as a nuclear fuel.
This video seeks to clarify this dispute.
Music in this video was created by KiloWatts: http://KiloWattsMusic.com/
Video assets were remixed from http://ThoriumRemix.com/ ,with some video excerpts from COSMOS with Dr. Neil deGrasse Tyson.
Video constructed by Gordon McDowell.
Reports cited are...
NNL [UKs National Nuclear Laboratory] Comparison of Thorium and Uranium Fuel Cycles: https://www.gov.uk/government/uploads/system/uploads/attachment_data/file/65504/6300-comparison-fuel-cycles.pdf
OECD NEAs Introduction of Thorium In The Nuclear Fuel Cycle: https://www.oecd-nea.org/science/pubs/2015/7224-thorium.pdf
IEER Thorium Fact Sheet: http://energyfromthorium.com/ieer-rebuttal/ (I will not be linking to IEER. Easy to Google.)
For a multi-hour in-depth look at Thorium, see video Thorium.: https://youtu.be/2oK6Rs6yFsM THORIUM DEBUNK](https://i.ytimg.com/vi/H6mhw-CNxaE/mqdefault.jpg)

