vaultfox | Fixing a BUSTED Print // 3D Printing a 332nd Clone Trooper Helmet from The Clone Wars @vaultfox | Uploaded July 2020 | Updated October 2024, 3 hours ago.
Clone STL Files: galacticarmory.net/products/phase-2-animated-clone-trooper-helmet-3d-print-files?_pos=11&_sid=5c11e746a&_ss=r&aff=8
use code VAULTFOX for 10% off your order with Galactic Armory!
I'm back with another helmet build! This time I printed a 332nd Clone helmet from the last season of The Clone Wars. The audio is once again a bit wonky as I continue to figure out the best setup for all of this but I figured it was better to publish as is to get it out there :) STILL LEARNING! haha
Let me know if you have any questions or comments down below, especially if you plan on making one of these helmets yourself!
instagram: instagram.com/VAULTFOX
I'm also on tiktok!: tinyurl.com/ych7ddnb
--------------------------------
Paints Used
Montana Gold in Shock White - shrsl.com/30qoc
Montana Gold in Shock Orange - shrsl.com/30qpu
Bondo Can: amzn.to/3lfIlSX
Filler Primer: hamzn.to/3niCb6h
Sandpaper (I use 120 and 220 mostly): amzn.to/30C3TRR
Bondo: amzn.to/3l8FY4i
Welding Visor for Lens: amzn.to/36BHRCr
Creality CR-10 Printer: amzn.to/2SGwZL
○ Zyltech Filament (I use 1.75mm PLA): https://www.zyltech.com?aff=81
use code VAULTFOX5OFF for 5% off your order of Zyltech filament!
Mirror Tiles: amzn.to/3cXWph8
Binder Clips: amzn.to/3iueapv
Glue Sticks (for bed adhesion): amzn.to/3jCPZ9C
Putty Scrapers (for removing prints from the bed): amzn.to/33zfQtD
Plastic Clippers: amzn.to/3jKei5m
Clone STL Files: galacticarmory.net/products/phase-2-animated-clone-trooper-helmet-3d-print-files?_pos=11&_sid=5c11e746a&_ss=r&aff=8
use code VAULTFOX for 10% off your order with Galactic Armory!
I'm back with another helmet build! This time I printed a 332nd Clone helmet from the last season of The Clone Wars. The audio is once again a bit wonky as I continue to figure out the best setup for all of this but I figured it was better to publish as is to get it out there :) STILL LEARNING! haha
Let me know if you have any questions or comments down below, especially if you plan on making one of these helmets yourself!
instagram: instagram.com/VAULTFOX
I'm also on tiktok!: tinyurl.com/ych7ddnb
--------------------------------
Paints Used
Montana Gold in Shock White - shrsl.com/30qoc
Montana Gold in Shock Orange - shrsl.com/30qpu
Bondo Can: amzn.to/3lfIlSX
Filler Primer: hamzn.to/3niCb6h
Sandpaper (I use 120 and 220 mostly): amzn.to/30C3TRR
Bondo: amzn.to/3l8FY4i
Welding Visor for Lens: amzn.to/36BHRCr
Creality CR-10 Printer: amzn.to/2SGwZL
○ Zyltech Filament (I use 1.75mm PLA): https://www.zyltech.com?aff=81
use code VAULTFOX5OFF for 5% off your order of Zyltech filament!
Mirror Tiles: amzn.to/3cXWph8
Binder Clips: amzn.to/3iueapv
Glue Sticks (for bed adhesion): amzn.to/3jCPZ9C
Putty Scrapers (for removing prints from the bed): amzn.to/33zfQtD
Plastic Clippers: amzn.to/3jKei5m
