Fidget light how to make @Pricklysauce

Uploaded May 2017 | Updated September 2026, 51 minutes ago

Fidget light - how to make

Make a FIDGET LIGHT!

I had a bicycle rear wheel hub left over from my Softbox light project...check the video out to see more youtube.com/watch?v=W2gIiQ4xCM4

The wheel hub was kicking around the workshop though I would play with it, it looks so cool and I loved twisting the cassette hub to hear it click...

...I wonder if it could be made into a Fidget light?

Get a piece of steel rod as an armature for the light...

...drill a hole in the hub for the rod and glue in place with epoxy glue.

Thread some lighting wire through the wheel hub and safely wire up to a threaded lamp holder...screw this to the hub.

Paint the wire black...add a nut on the end and glue the wire in place.

Get a vintage laboratory stand and fix the fidget light to the stand...

...find your favourite place...

Switch on...and FIDGET!

You don't have a vintage lab stand to hand?

Get some threaded rod, drill a hole for the fidget light armature to slide through...

...clamp in a pillar drill vice...

...for a funky industrial design look...

OR get a nice plank of wood...plane flat and sand and oil...

...drill a hole and thread the threaded bolt into the wood...slide on the fidget light...COOL

BUT I WANT IT ON THE WALL...

Make a circle of ply with a bandsaw circle cutting sled...

Drill out a hole...stencil some cool graphics...

...pop in a bearing...

...play with your new fidget spinner...

...drill a hole in the wall...

...and fit the fidget light and spinner in the hole for a super cool wall mounted fidget light / fidget spinner combo.

SUPER COOL!

Hey thanks Otis McDonald for your cool tune 'Heavy Petting' available for free use through YouTubes creative suite.

Why not subscribe to catch all of the videos as soon as they are uploaded : youtube.com/c/Pricklysauce?sub_confirmation=1

Visit my website to see what I am creating at pricklysauce.com

Or Like my Facebook page : facebook.com/pricklysauce

Follow me on Twitter : twitter.com/Pricklysauce

and Instagram : instagram.com/pricklysauce

Hot news! I am now on Instructables : instructables.com/member/pricklysauce

and now on Make : community.makezine.com/share/pricklysauce/projects

Thanks for watching and please come back to watch some more.

How to make a windsurfer into a Wave ski

$Metal milling How to Metal milling How to http://www.pricklysauce.com With Pricklysaucess latest project the Bike Wardrobe I needed to make a hasp for the locking throw bolt. I had a piece of 5mm thick aluminium sheet in the workshop which would do nicely, though I required a nice clean slot cut into it. I work with wood and have no experience of doing this, so I searched on the internet and a couple of YouTube videos later I had learnt that I could use my woodworking router and high speed steel [HSS] router cutter to do the job. I removed the plastic baseplate from the router and cut a scrap piece of 4mm ply larger than the router base to enable it to be screwed down. Cut a slot so that the cutter can pass through and to see the progress clearly. Drill and countersink holes to re-fix the ply to the base of the router. I cut a 50mm strip of the aluminium. I then made up the jig by screwing two 6mm thick pieces of MDF to a thicker [12-18mmthick] piece of MDF, to retain the aluminium though to allow it to slide back and forth without slack. The router and ply baseplate were positioned and screwed to the jig. The whole thing was screwed securely to the work bench. It has to be solid and no chance to move. The router can plunge and the aluminium strip can slide. No other movement. I fixed stops at either end of the aluminium strip to the desired cutting length of the slot. I fitted an old plunge cutting HSS router with the cutter profile on the bottom as well as the sides. I dont expect that it will be much good for cutting wood again! Put on ear defenders and ear protectors, switch on and carefully plunge, milling slightly into the aluminium. I found that only a fraction of a millimeter could be milled at a time, I listened to the sound of the cutter to determine the strain on the cutter. Slowly slide the aluminium strip back and forth. Continue the process until you mill all the way through. Remove the strip and there I have it, a nicely milled clean slot in metal, perfect for finishing my bolt on the door of the bike wardrobe. FANTASTIC! Catch the full build of the Bike Wardrobe from pricklysauce at https://www.youtube.com/watch?v=4PUuORmUox0&list=PLFCVDcgb4Bysrw8NtUqjueD3cmeh3B74K I also make a series of videos called Its a Rubbish Challenge where I challenge myself to give the things that we throw away a new life, to make them useful or adapt them to save buying in new stuff. I aim to make them all interesting and I hope they may inspire you to give it a go, take a look at your rubbish bin and make yourself something great from it. Why not subscribe to catch all of the videos as soon as they are uploaded : https://www.youtube.com/channel/UCL2soflHdZyT0PgrVxakxWA?sub_confirmation=1 Visit my website to see what I am creating at http://www.pricklysauce.com Or Like my Facebook page : https://www.facebook.com/pricklysauce/ Follow me on Twitter : https://twitter.com/Pricklysauce Hot news! I am now on Instructables : http://www.instructables.com/member/pricklysauce Thanks for watching and please come back to watch some more.$