Uploaded November 2022 | Updated November 2026, 2 hours ago
Patches and patch notes can be found at:
Time stamps: patchstorage.com/cosmic-grains-loops-two-experimental-ambient-delays-with-configurable-routing
0:00 Intro sound examples
Walkthrough
0:53 Introduction / overview
3:08 Delay controls (the same across both patches)
10:15 Cosmic Grains-specific controls
13:27 Cosmic Loops-specific controls
Cosmic Grains sound examples
19:00 Glitch-pitch vibraphone: granular in pre-delay position, one side pitched up an octave.
19:45 Same as above, but now with the granular placed post-delay.
20:27 Long delay, glitch marimba: granular is in pre-delay position.
23:07 Long delay, glitch marimba: granular is in post-delay position.
23:40 If you want to compensate for the pitch feedback, you can set the blur amount toward the ping-pong settings (~.85). With one side plus one octave and the other minor one octave, the pitch stabilizes somewhat.
24:27 Now some strings: granular is in pre-delay position, but same settings as last example, with the blur set high, so the pitched sounds move around the delay network. Then, I take the blur down to almost zero, and we can hear how the granular-affected sounds are preserved.
26:17 Same as before, but now with the granular post-delay.
27:01 Slowly melting glitch piano: granular in post-delay position. High warble level. Low-pass filter adjusted to cut some high-end.
27:48 Now with some plate reverb added from the Empress Reverb (the audio clips a little here, sorry about that).
Cosmic Loops sound examples
29:21 Looper in feedback position. Cheesy choir sound. The most dramatic effect comes from the start and end modulation, which introduces glitchy stutters.
30:21 Drifting palindromic piano. Looper is still in feedback position. L/R loopers are slightly detuned positive and negative, so the pitch drifts a little with each cycle.
31:18 Playing with slewed delay time as a (destructive) performance tool.
31:51 Looper in pre-delay position. High blur amount so the affected loops ping-pong around. One is pitched up an octave and reversed, the other is played at the original speed and direction.
32:42 Glitchy, melting marimba. Looper is in post-delay position. Both sides reversed, one pitched up. Lots of warble, with some glitching from start/end modulation.
33:44 Reverse, phase piano. Looper is in pre-delay position. Reverse both sides. Blur is set to 0, so the offset of the delay lines introduces a Reichian phasing quality.
35:21 Now I move the loopers to post-delay position, maintaining the same buffer, and add some start/end modulation and pitch one side up an octave. Later, I add warble and plate reverb from the Empress Reverb.
37:34 Reversed, glitchy marimba. Looper is in post-delay position. Both loopers are reversed and pitched up. Shenanigans with start/end modulation.
38:30 More glitchy marimba.
39:17 Now with the loopers placed pre-delay, so the glitching gets passed around the delay network. Reverb from EE Reverb added again.
41:17 Bonus blooper
Patches and patch notes can be found at:
Time stamps: patchstorage.com/cosmic-grains-loops-two-experimental-ambient-delays-with-configurable-routing
0:00 Intro sound examples
Walkthrough
0:53 Introduction / overview
3:08 Delay controls (the same across both patches)
10:15 Cosmic Grains-specific controls
13:27 Cosmic Loops-specific controls
Cosmic Grains sound examples
19:00 Glitch-pitch vibraphone: granular in pre-delay position, one side pitched up an octave.
19:45 Same as above, but now with the granular placed post-delay.
20:27 Long delay, glitch marimba: granular is in pre-delay position.
23:07 Long delay, glitch marimba: granular is in post-delay position.
23:40 If you want to compensate for the pitch feedback, you can set the blur amount toward the ping-pong settings (~.85). With one side plus one octave and the other minor one octave, the pitch stabilizes somewhat.
24:27 Now some strings: granular is in pre-delay position, but same settings as last example, with the blur set high, so the pitched sounds move around the delay network. Then, I take the blur down to almost zero, and we can hear how the granular-affected sounds are preserved.
26:17 Same as before, but now with the granular post-delay.
27:01 Slowly melting glitch piano: granular in post-delay position. High warble level. Low-pass filter adjusted to cut some high-end.
27:48 Now with some plate reverb added from the Empress Reverb (the audio clips a little here, sorry about that).
Cosmic Loops sound examples
29:21 Looper in feedback position. Cheesy choir sound. The most dramatic effect comes from the start and end modulation, which introduces glitchy stutters.
30:21 Drifting palindromic piano. Looper is still in feedback position. L/R loopers are slightly detuned positive and negative, so the pitch drifts a little with each cycle.
31:18 Playing with slewed delay time as a (destructive) performance tool.
31:51 Looper in pre-delay position. High blur amount so the affected loops ping-pong around. One is pitched up an octave and reversed, the other is played at the original speed and direction.
32:42 Glitchy, melting marimba. Looper is in post-delay position. Both sides reversed, one pitched up. Lots of warble, with some glitching from start/end modulation.
33:44 Reverse, phase piano. Looper is in pre-delay position. Reverse both sides. Blur is set to 0, so the offset of the delay lines introduces a Reichian phasing quality.
35:21 Now I move the loopers to post-delay position, maintaining the same buffer, and add some start/end modulation and pitch one side up an octave. Later, I add warble and plate reverb from the Empress Reverb.
37:34 Reversed, glitchy marimba. Looper is in post-delay position. Both loopers are reversed and pitched up. Shenanigans with start/end modulation.
38:30 More glitchy marimba.
39:17 Now with the loopers placed pre-delay, so the glitching gets passed around the delay network. Reverb from EE Reverb added again.
41:17 Bonus blooper










