Uploaded November 2026 | Updated November 2026, 4 days ago
In this video, I solve Problem 1 of the EM 304 test that Dr. Judy Wood gave her students on February 6, 2003, five days after the Space Shuttle Columbia disaster. If a thermal tile is lost, how hot can an aluminum tube held between two rigid support plates get before something fails? I check three candidates: compression in the aluminum tube (442.2 °F), bearing on the plate at the tube end (515.9 °F), and shear in the plate around the tube (205.03 °F). The shear stress in the plate arises due to the compressive stress in the tube that the plate is connected to. Since the temperature of 205 °F is the lowest, the failure occurs first as shear in the plate, even though the corresponding compressive stress in the tube (27.8 ksi) is far less than its strength limit of 60 ksi.
#math #science #engineering #nasa #physics
Timestamps:
- 0:00 – Problem 1 of EM 304 on February 6, 2003: Possible cause of failure is the loss of a thermal tile.
- 1:01 – Problem assumptions: Aluminum tube is heated uniformly while the remaining structure is at 0° F.
- 3:26 – Given three volume elements to examine the corresponding stresses and temperatures at failure.
- 6:20 – Material properties for the support plates and aluminum tube.
- 9:33 – Three questions: Determine maximum temperature of the aluminum tube before failure, first failure location, stress states at the three volume elements, and draw these stress state diagrams.
- 11:17 – Location descriptions: Point A is inside the top plate, B is the surface between the plate and tube, Point C is the outer surface of the aluminum tube.
- 12:02 Solution: I used Dr. Judy Wood's solution key and Grok AI's assistance in this solution.
- 12:20 – Thermal expansion properties: Support plates are idealized as perfectly rigid and non-expanding, while the aluminum tube uses the 2014-T6 aluminum alloy properties.
- 12:38 – Strength limits of the plates and tube. Note that ksi = kips per square inch = 1000 psi.
- 14:52 – Solution to (a): Maximum temperature without failure.
- 17:33 – The aluminum tube is assumed to be of constant length, which means the thermal expansion displacement is equal to the resulting compressive displacement.
- 20:17 – Equation for thermal displacement involving the coefficient of linear thermal expansion.
- 22:21 – Equation for Young's Modulus and compressive stress.
- 24:30 – Rearrange to obtain our temperature increase formula (and force that develops in the tube).
- 27:16 – Candidate 1: Aluminum tube in compression (point C).
- 29:07 – Maximum temperature at failure at point C is 442.2 °F.
- 32:04 – Candidate 2: Plate bearing at the tube end (point B).
- 34:40 – Plates are idealized as rigid and non-expanding, so we have to scale up the temperature of the aluminum tube by the ratio of the plate to tube compressive strength limits and obtain failure temperature of 515.9 °F at point B.
- 35:47 – Candidate 3: Shear at the plate connection (point A)
- 37:19 – Free body diagram of the shear stress in the plate due to the compressive stress in the tube
- 42:27 – "Unrolling" the circular shear stress to obtain a rectangle corresponding to the shear area
- 45:40 – By equilibrium, we obtain a formula for the compressive stress in the tube as a function of the shear stress in the plate and the ratio of the shear area to compressive area
- 49:00 – Temperature at failure at point A is 205.03 °F
- 53:30 – Solution to (b): It fails at point A first, shear in the plate, because its failure temperature is the lowest
- 54:33 – Solution to part (c): Stress state at the failure temperature
- 55:46 – Obtain compressive stress in the aluminum from the shear stress in the plate using our earlier derived formula, and get 27.8 ksi, which is also the uniaxial compressive stress at point C and bearing stress at point B. This stress is well below the plate and tube allowable compressive stresses
- 59:02 – Solution to (d): Volume-element sketches
- 59:38 – Note: The "1 + 2" are actually points Dr. Judy Wood gives when grading tests.
- 1:03:30 – Shear stress diagram needs to have arrows be in equilibrium aka not rotating
- 1:06:02 – Summary of the Engineering Logic: Compressive stress in the tube causes failure in shear at the plate, even though the compressive stress is far below its strength limit
Notes and playlists:
- Notes: https://mes.fm/em-304-failure-temperature-columbia
- Full video: https://mes.fm/space-shuttle-columbia
- https://mes.fm/math
------------------------------------------------------
MES: https://mes.fm
Donate: https://mes.fm/donate
MES Truth: youtube.com/@mestruth
Hive: peakd.com/@mes
Email me: contact@mes.fm
In this video, I solve Problem 1 of the EM 304 test that Dr. Judy Wood gave her students on February 6, 2003, five days after the Space Shuttle Columbia disaster. If a thermal tile is lost, how hot can an aluminum tube held between two rigid support plates get before something fails? I check three candidates: compression in the aluminum tube (442.2 °F), bearing on the plate at the tube end (515.9 °F), and shear in the plate around the tube (205.03 °F). The shear stress in the plate arises due to the compressive stress in the tube that the plate is connected to. Since the temperature of 205 °F is the lowest, the failure occurs first as shear in the plate, even though the corresponding compressive stress in the tube (27.8 ksi) is far less than its strength limit of 60 ksi.
#math #science #engineering #nasa #physics
Timestamps:
- 0:00 – Problem 1 of EM 304 on February 6, 2003: Possible cause of failure is the loss of a thermal tile.
- 1:01 – Problem assumptions: Aluminum tube is heated uniformly while the remaining structure is at 0° F.
- 3:26 – Given three volume elements to examine the corresponding stresses and temperatures at failure.
- 6:20 – Material properties for the support plates and aluminum tube.
- 9:33 – Three questions: Determine maximum temperature of the aluminum tube before failure, first failure location, stress states at the three volume elements, and draw these stress state diagrams.
- 11:17 – Location descriptions: Point A is inside the top plate, B is the surface between the plate and tube, Point C is the outer surface of the aluminum tube.
- 12:02 Solution: I used Dr. Judy Wood's solution key and Grok AI's assistance in this solution.
- 12:20 – Thermal expansion properties: Support plates are idealized as perfectly rigid and non-expanding, while the aluminum tube uses the 2014-T6 aluminum alloy properties.
- 12:38 – Strength limits of the plates and tube. Note that ksi = kips per square inch = 1000 psi.
- 14:52 – Solution to (a): Maximum temperature without failure.
- 17:33 – The aluminum tube is assumed to be of constant length, which means the thermal expansion displacement is equal to the resulting compressive displacement.
- 20:17 – Equation for thermal displacement involving the coefficient of linear thermal expansion.
- 22:21 – Equation for Young's Modulus and compressive stress.
- 24:30 – Rearrange to obtain our temperature increase formula (and force that develops in the tube).
- 27:16 – Candidate 1: Aluminum tube in compression (point C).
- 29:07 – Maximum temperature at failure at point C is 442.2 °F.
- 32:04 – Candidate 2: Plate bearing at the tube end (point B).
- 34:40 – Plates are idealized as rigid and non-expanding, so we have to scale up the temperature of the aluminum tube by the ratio of the plate to tube compressive strength limits and obtain failure temperature of 515.9 °F at point B.
- 35:47 – Candidate 3: Shear at the plate connection (point A)
- 37:19 – Free body diagram of the shear stress in the plate due to the compressive stress in the tube
- 42:27 – "Unrolling" the circular shear stress to obtain a rectangle corresponding to the shear area
- 45:40 – By equilibrium, we obtain a formula for the compressive stress in the tube as a function of the shear stress in the plate and the ratio of the shear area to compressive area
- 49:00 – Temperature at failure at point A is 205.03 °F
- 53:30 – Solution to (b): It fails at point A first, shear in the plate, because its failure temperature is the lowest
- 54:33 – Solution to part (c): Stress state at the failure temperature
- 55:46 – Obtain compressive stress in the aluminum from the shear stress in the plate using our earlier derived formula, and get 27.8 ksi, which is also the uniaxial compressive stress at point C and bearing stress at point B. This stress is well below the plate and tube allowable compressive stresses
- 59:02 – Solution to (d): Volume-element sketches
- 59:38 – Note: The "1 + 2" are actually points Dr. Judy Wood gives when grading tests.
- 1:03:30 – Shear stress diagram needs to have arrows be in equilibrium aka not rotating
- 1:06:02 – Summary of the Engineering Logic: Compressive stress in the tube causes failure in shear at the plate, even though the compressive stress is far below its strength limit
Notes and playlists:
- Notes: https://mes.fm/em-304-failure-temperature-columbia
- Full video: https://mes.fm/space-shuttle-columbia
- https://mes.fm/math
------------------------------------------------------
MES: https://mes.fm
Donate: https://mes.fm/donate
MES Truth: youtube.com/@mestruth
Hive: peakd.com/@mes
Email me: contact@mes.fm




![Vortex Math is Based on the Modulo Multiplication Identity
In this video I show that the previous result of multiplying a number and its vortex sum yields the same vortex sum can be written in its equivalent modulo multiplication identity. Since we have already established that the vortex sum of an integer (summing the digits until we get a single digit) is the same as the modulo of that number with the modulus being the base - 1, we can rewrite the vortex sums using the modulo operations. In general, if we have integers A, B, and C, then we have the identity AB mod C = [A·(B mod C)] mod C. Furthermore we can apply this same identity with the integers inside the bracket to also get it equal to [( A mod C)(B mod C)] mod C and [(A mod C)·B] mod C. Pretty epic stuff!
#math #vortexmath #modulararithmetic #numbertheory #education
Timestamps:
- Vortex math multiplication as an equivalent modulo identity – 0:00
- 25 * 4 = 100 v= 1 or 25 v= 7 * 4 = 28 v= 1 – 0:38
- (4*25) mod 9 = [4*(25 mod 9)] mod 9 = 1 – 1:59
- Generalize modulo operation to any integer multiple or modulus: (AB mod C = [A(B mod C)] mod C = [(A mod C)(B mod C)] mod C = [(A mod C)B] mod C – 3:00
- Example: A = 11, B = 22, C = 7 – 4:44
- Reason is because modulo operation gives integers, which can just apply the same identity over again – 5:51
– Modulo of a multiplication of integers is the same as the modulo of the multiplication of either or both modulo of the integers – 6:54
Notes and playlists:
- Summary: https://inleo.io/threads/view/mes/re-leothreads-2epxg3553
- Notes: https://peakd.com/hive-128780/@mes/messcience-2-vortex-math-part-1-number-theory-and-modular-arithmetic
- Vortex Math playlist: https://www.youtube.com/playlist?list=PLai3U8-WIK0EbRnMsUBx2RxlerL7GQuLX
- MES Science playlist: https://www.youtube.com/playlist?list=PLai3U8-WIK0GhjCHmTw1XbqMD_EdVKdd9 .
Become a MES Super Fan! https://www.youtube.com/channel/UCUUBq1GPBvvGNz7dpgO14Ow/join
DONATE! ʕ •ᴥ•ʔ https://mes.fm/donate
SUBSCRIBE via EMAIL: https://mes.fm/subscribe
MES Links: https://mes.fm/links
MES Truth: https://mes.fm/truth
Official Website: https://MES.fm
Hive: https://peakd.com/@mes
Email me: contact@mes.fm
Free Calculators: https://mes.fm/calculators
BMI Calculator: https://bmicalculator.mes.fm
Grade Calculator: https://gradecalculator.mes.fm
Mortgage Calculator: https://mortgagecalculator.mes.fm
Percentage Calculator: https://percentagecalculator.mes.fm
Free Online Tools: https://mes.fm/tools
iPhone and Android Apps: https://mes.fm/mobile-apps Vortex Math is Based on the Modulo Multiplication Identity](https://i.ytimg.com/vi/cJTiB6njXAc/mqdefault.jpg)





