Uploaded November 2026 | Updated November 2026, 3 hours ago
Ecobee wired and the install looks clean, but the blower still won’t slow down to pull moisture out? On two-stage systems, dehumidification is the setup step techs miss most often. In this video, the team walks through the Ecobee settings that make dehumidify-on-demand work, and the field checks that confirm it before you leave the job.
The “dehumidifier” here isn’t a standalone unit. The Ecobee controls the equipment’s DH input through a one-wire accessory on ACC+. When the relay opens and drops 24V, the indoor fan slows down, which gives you a colder coil and more moisture removal. If the relay is set wrong or the feature is never turned on, the system runs at full airflow and the humidity stays high.
Install and Equipment Setup
Accessory: select the one-wire option on ACC+
Relay: normally open (open = no power = reduced fan speed)
Dehumidify with fan: No
Minimum runtime delta: change it from the factory 5% to 2%
Dehumidify in heat mode: No, because the system itself is doing the dehumidification
Relay state: confirm it reads open, and correct it here if it says closed
Still Not Working? It’s Off by Default
Even after you set it up as an accessory, Ecobee dehumidification defaults to off. Go to the main menu, then the gear icon and system/equipment settings. Turn the dehumidifier on and set your target. We use 56% RH because 54% was hard to hit reliably.
Check It in Test Mode
Use test mode to call first and second stage cooling. Keep 24V on DH while you set the charge so you have full airflow. Then toggle dehumidification on and off and check that the fan speed drops and ramps back up. You’ll be able to hear the change.
Set Expectations with the Customer
Overcool to dehumidify can run the house a couple of degrees below setpoint. Explain that up front so you don’t get a “too cold” callback. And plug in the remote sensors.
---
NEXT VIDEO
Ecobee Smart Thermostat Setup - Two Stage Systems & Client Support
youtube.com/watch?v=7vZIkC9RerY&t=6s
KEEP LEARNING
Start here:
hvacrschool.com/start
Free HVAC/R training, tech tips, quizzes, calculators, courses, and more:
hvacrschool.com
Listen to the HVAC School podcast:
hvacrschool.com/podcast
Get the HVAC School app:
hvacrschool.com/apps-page
HVAC School provides free HVAC/R training—primarily for techs, by techs. The goal is not just to collect facts. It is to understand the system well enough to apply what you know in the field.
Questions or corrections? Leave a comment and include the equipment model, measurements, and source when you can. None of us gets everything right, and good measurements beat confident guesses.
This content is educational. Follow manufacturer instructions, use proper PPE and safe work practices, and comply with the codes and standards that apply to your equipment and jurisdiction.
Ecobee wired and the install looks clean, but the blower still won’t slow down to pull moisture out? On two-stage systems, dehumidification is the setup step techs miss most often. In this video, the team walks through the Ecobee settings that make dehumidify-on-demand work, and the field checks that confirm it before you leave the job.
The “dehumidifier” here isn’t a standalone unit. The Ecobee controls the equipment’s DH input through a one-wire accessory on ACC+. When the relay opens and drops 24V, the indoor fan slows down, which gives you a colder coil and more moisture removal. If the relay is set wrong or the feature is never turned on, the system runs at full airflow and the humidity stays high.
Install and Equipment Setup
Accessory: select the one-wire option on ACC+
Relay: normally open (open = no power = reduced fan speed)
Dehumidify with fan: No
Minimum runtime delta: change it from the factory 5% to 2%
Dehumidify in heat mode: No, because the system itself is doing the dehumidification
Relay state: confirm it reads open, and correct it here if it says closed
Still Not Working? It’s Off by Default
Even after you set it up as an accessory, Ecobee dehumidification defaults to off. Go to the main menu, then the gear icon and system/equipment settings. Turn the dehumidifier on and set your target. We use 56% RH because 54% was hard to hit reliably.
Check It in Test Mode
Use test mode to call first and second stage cooling. Keep 24V on DH while you set the charge so you have full airflow. Then toggle dehumidification on and off and check that the fan speed drops and ramps back up. You’ll be able to hear the change.
Set Expectations with the Customer
Overcool to dehumidify can run the house a couple of degrees below setpoint. Explain that up front so you don’t get a “too cold” callback. And plug in the remote sensors.
---
NEXT VIDEO
Ecobee Smart Thermostat Setup - Two Stage Systems & Client Support
youtube.com/watch?v=7vZIkC9RerY&t=6s
KEEP LEARNING
Start here:
hvacrschool.com/start
Free HVAC/R training, tech tips, quizzes, calculators, courses, and more:
hvacrschool.com
Listen to the HVAC School podcast:
hvacrschool.com/podcast
Get the HVAC School app:
hvacrschool.com/apps-page
HVAC School provides free HVAC/R training—primarily for techs, by techs. The goal is not just to collect facts. It is to understand the system well enough to apply what you know in the field.
Questions or corrections? Leave a comment and include the equipment model, measurements, and source when you can. None of us gets everything right, and good measurements beat confident guesses.
This content is educational. Follow manufacturer instructions, use proper PPE and safe work practices, and comply with the codes and standards that apply to your equipment and jurisdiction.










