Uploaded June 2023 | Updated September 2026, 2 weeks ago
Dremel is releasing a new 3D printer and... it doesn't look bad?! It is running Core-XY, linear rails, auxiliary part cooling, dual direct drive extruders, high flow ceramic hotends, and KLIPPER FIRMWARE! Is this Dremel Digilab 3d printer actually good? It is just a prototype so only time will tell, but at that price, it is gonna be hard to see the value...
-----------------------------------------------------------------------------------------------
Please consider supporting by checking out my various links:
mandicreally.com/links
-----------------------------------------------------------------------------------------------
Filmed with:
*** Main Camera: amzn.to/3c6ULgV
*** Main Lens: amzn.to/3c616cp
*** Overhead Camera: amzn.to/2U4b1nZ
*** Video Recorder Used: amzn.to/3ymN90U
*** Action Camera: amzn.to/2ATHS73
*** Second Camera: amzn.to/371EhBM
*** B-Roll Lens: amzn.to/2xmg85L
*** Wide Angle Lens: amzn.to/2YiZTmH
*** Slider: amzn.to/3nGZ1Uh
*** Lav Mic: amzn.to/2DFwgR5
*** Shotgun Mic: amzn.to/2IjTJiB
*** Mini Tripod: amzn.to/2Eok8Fw
*** Monopod - amzn.to/2C1YEMU
*** Tripod: amzn.to/2yASruf
*** Gimbal: amzn.to/2FNwesV
*** Primary Lighting: amzn.to/2jHROnW
*** Additional Lighting: amzn.to/2DImspx
*** RGB Lights: amzn.to/2UUGAOk
*** Drone: amzn.to/2yDkwkI
-----------------------------------------------------------------------------------------------
The opinions expressed in this video are my own, from my personal experience. This is not a paid product advertisement. Please feel free to let me know what you think of this tool, or suggest alternatives I should check out. Disclaimer: This is not a paid advertisement. This video is solely my opinions from the use of these products and based on the specifications of them. Some of the links provided are AMAZON AFFILIATE LINKS or others. Affiliate links give the MandicReally a small advertising fee for every purchase made via those links. This does not cost you anything more than if you purchased them normally.
Dremel is releasing a new 3D printer and... it doesn't look bad?! It is running Core-XY, linear rails, auxiliary part cooling, dual direct drive extruders, high flow ceramic hotends, and KLIPPER FIRMWARE! Is this Dremel Digilab 3d printer actually good? It is just a prototype so only time will tell, but at that price, it is gonna be hard to see the value...
-----------------------------------------------------------------------------------------------
Please consider supporting by checking out my various links:
mandicreally.com/links
-----------------------------------------------------------------------------------------------
Filmed with:
*** Main Camera: amzn.to/3c6ULgV
*** Main Lens: amzn.to/3c616cp
*** Overhead Camera: amzn.to/2U4b1nZ
*** Video Recorder Used: amzn.to/3ymN90U
*** Action Camera: amzn.to/2ATHS73
*** Second Camera: amzn.to/371EhBM
*** B-Roll Lens: amzn.to/2xmg85L
*** Wide Angle Lens: amzn.to/2YiZTmH
*** Slider: amzn.to/3nGZ1Uh
*** Lav Mic: amzn.to/2DFwgR5
*** Shotgun Mic: amzn.to/2IjTJiB
*** Mini Tripod: amzn.to/2Eok8Fw
*** Monopod - amzn.to/2C1YEMU
*** Tripod: amzn.to/2yASruf
*** Gimbal: amzn.to/2FNwesV
*** Primary Lighting: amzn.to/2jHROnW
*** Additional Lighting: amzn.to/2DImspx
*** RGB Lights: amzn.to/2UUGAOk
*** Drone: amzn.to/2yDkwkI
-----------------------------------------------------------------------------------------------
The opinions expressed in this video are my own, from my personal experience. This is not a paid product advertisement. Please feel free to let me know what you think of this tool, or suggest alternatives I should check out. Disclaimer: This is not a paid advertisement. This video is solely my opinions from the use of these products and based on the specifications of them. Some of the links provided are AMAZON AFFILIATE LINKS or others. Affiliate links give the MandicReally a small advertising fee for every purchase made via those links. This does not cost you anything more than if you purchased them normally.
