Uploaded October 2026 | Updated November 2026, 3 hours ago
Wondering how to install door casing without a nail gun? In this video, I show you how to install door trim the old-school way using just a hammer and finish nails!
I bought a standard door that turned out to be 4 cm narrower than the old one, so the drywall and wallpaper around the frame were completely ruined. Instead of wasting days patching and painting, I show you my secret hack to hide a damaged wall by shifting the trim outward.
To keep it beginner-friendly, I use a pre-cut door casing kit. The top corners are already cut at 45 degrees, so you don't need a miter saw. You only make one straight cut at the bottom.
Plus, I share my favorite painter's tape hack and show you how to pre-start your nails while the casing is flat, so the boards don't move. A nail punch gives you a professional finish without a nail gun.
🔨 Tools used:
- Hammer
- Finish nails
- Painter's tape
- Nail punch (nail set)
Is this a genius budget hack or completely terrible? Let me know in the comments below!
👉 In this video, you will learn:
- How to install door casing without a nail gun
- How to hide damaged drywall around a door frame
- How to use a pre-cut mitered door trim kit (no miter saw needed)
- How to use a nail punch (nail set) for a professional finish
If this video helped you, please LIKE and SUBSCRIBE for more easy DIY and home improvement tips!
#DoorCasing #DoorTrim #HowToInstallDoorCasing #DIYHomeImprovement #HandToolsOnly #NoNailGun
CHAPTERS:
0:00 - The Problem: Narrower Door & Ruined Drywall
0:40 - The Pre-Cut Door Casing Kit Hack
1:05 - Hand Tools Only: The Tools You Need
1:35 - Pro Tip: Pre-Start Nails While the Casing Is Flat
2:10 - The Painter's Tape Hack (Genius or Terrible?)
2:45 - Nailing It Down: How to Use a Nail Punch
3:00 - The Result: Ruined Wall Hidden, No Nail Gun Needed
Wondering how to install door casing without a nail gun? In this video, I show you how to install door trim the old-school way using just a hammer and finish nails!
I bought a standard door that turned out to be 4 cm narrower than the old one, so the drywall and wallpaper around the frame were completely ruined. Instead of wasting days patching and painting, I show you my secret hack to hide a damaged wall by shifting the trim outward.
To keep it beginner-friendly, I use a pre-cut door casing kit. The top corners are already cut at 45 degrees, so you don't need a miter saw. You only make one straight cut at the bottom.
Plus, I share my favorite painter's tape hack and show you how to pre-start your nails while the casing is flat, so the boards don't move. A nail punch gives you a professional finish without a nail gun.
🔨 Tools used:
- Hammer
- Finish nails
- Painter's tape
- Nail punch (nail set)
Is this a genius budget hack or completely terrible? Let me know in the comments below!
👉 In this video, you will learn:
- How to install door casing without a nail gun
- How to hide damaged drywall around a door frame
- How to use a pre-cut mitered door trim kit (no miter saw needed)
- How to use a nail punch (nail set) for a professional finish
If this video helped you, please LIKE and SUBSCRIBE for more easy DIY and home improvement tips!
#DoorCasing #DoorTrim #HowToInstallDoorCasing #DIYHomeImprovement #HandToolsOnly #NoNailGun
CHAPTERS:
0:00 - The Problem: Narrower Door & Ruined Drywall
0:40 - The Pre-Cut Door Casing Kit Hack
1:05 - Hand Tools Only: The Tools You Need
1:35 - Pro Tip: Pre-Start Nails While the Casing Is Flat
2:10 - The Painter's Tape Hack (Genius or Terrible?)
2:45 - Nailing It Down: How to Use a Nail Punch
3:00 - The Result: Ruined Wall Hidden, No Nail Gun Needed

![I Poured ONE Concrete Floor Over TWO Different Structures… Will It Crack?
Everyone told me this concrete floor would crack... but I did it anyway.
In this video, I’m pouring 20 m² of floor heating over TWO completely different structures. One side is solid concrete over a basement – the other side is a 40 cm deep hole I dug myself.
Can one single slab survive being poured over a moving foundation? Or do I have a secret trick up my sleeve to save the floor? Stick around to see the technical solution and the final bill!
[DANSK VERSION]
Alle sagde, at det her betongulv ville flække... men jeg gjorde det alligevel.
Jeg støber 20 m² gulvvarme over TO forskellige underlag. Den ene halvdel er beton over en kælder – den anden halvdel har jeg gravet 40 cm ned i jorden.
Kan ét samlet gulv holde til at ligge på to så forskellige fundamenter uden at revne? Eller har jeg et teknisk trick, der redder det hele? Se med til slutningen for at se løsningen... og den endelige regning!
HIGHLIGHTS IN THIS VIDEO:
• The Foundation Struggle: Digging 40 cm down by hand to prep the floor.
• The Big Dilemma: One slab or two? How to prevent the concrete from cracking.
• Energy Crisis: How I’m fighting a 50% price hike in district heating.
• The Solution: My controlled expansion joint (flamingo) hack.
• The Budget: Can we finish this for under $1,400 (10.000 kr.)?
THE COST BREAKDOWN (TOTAL):
💰 Final Cost: 9.218 KR. ($1,325)
(Includes insulation, pex-pipes, reinforcement, and concrete)
POLL: WHAT WOULD YOU DO?
Would you have risked pouring it as one single piece, or would you play it safe like me? Let me know in the comments!
0:00 Intro: The Big Gamble
1:30 The 40cm Dig & Foundation
3:00 Why two structures?
5:00 Price check: Insulation & Pipes
7:30 The Secret Solution: Expansion Joint
10:00 Pouring the Concrete
11:30 Final result & The Total Bill
👇
SUPPORT THE CHANNEL / STØT KANALEN:
✅ Subscribe for more DIY experiments and budget-friendly renovations!
🔔 Hit the bell so you dont miss the next step of the project!
Business inquiries: see channel About page
HASHTAGS:
#ConcreteFloor #DIY #FloorHeating #HomeRenovation #Gulvvarme #Construction #Beton I Poured ONE Concrete Floor Over TWO Different Structures… Will It Crack?](https://i.ytimg.com/vi/8Rn88YQP9iQ/mqdefault.jpg)








