Uploaded August 2026 | Updated November 2026, 5 hours ago
Visit https://diyrot.epss.ucla.edu/ to use DIYrotate! Further details on purchasing parts for the Sidewall Tank will be added to the DIYnamics website.
Learn more about the DIYnamics Project, including how to perform experiments yourself and additional LEGO-Based Table add-ons, at diynamics.github.io
This video is made possible with support from the National Science Foundation. Any opinions, findings, and conclusions or recommendations expressed in this video are those of the authors and do not necessarily reflect the views of the National Science Foundation.
Visit https://diyrot.epss.ucla.edu/ to use DIYrotate! Further details on purchasing parts for the Sidewall Tank will be added to the DIYnamics website.
Learn more about the DIYnamics Project, including how to perform experiments yourself and additional LEGO-Based Table add-ons, at diynamics.github.io
This video is made possible with support from the National Science Foundation. Any opinions, findings, and conclusions or recommendations expressed in this video are those of the authors and do not necessarily reflect the views of the National Science Foundation.







![Kinematically-Reversible Magneto-Couette Flow: The Gory Details
A delightful, chalkboard style, portrayal of viscous Magneto-Couette flow which is demonstrated in tandem with experimental videos.
EXPERIMENTAL DETAILS :
Experiment Dimensions:
Setup: r_o = 9.75 [cm]; r_in = 3.75 [cm]; volume liquid: 250 [mL]; height liquid = 1 [cm]
Brine salinity = 19.3 [ppt]; corn syrup:brine, 3:2; density = 1153.6 [kg/m^3]; conductivity = 8021 [uS/cm]; resistance = 39.8 [ohms]; Current = .088 [A]
The magnetic field varied quite a bit in total, but where the particles were in the video at r1 = 5.58e-2 [m], r2 = 6.49e-2 [m], and r3 = 7.27e-2 [m], the magnetic fields were 211 +/- 7 [G], 216 +/-10 [G], 225 +/- 6 [G].
AJs Personal Notes:
GETTING THE SYSTEM TO MAGNETO-COUETTE:
I originally started with high salinity brine and increased the percentage of cornsyrup and ran the experiment. I checked to see if the solution was conducting, if there was corrosion on the stainless steel, how bad the surface was, and if bubbles formed in the fluid. Many of my observations concerning conductivity actually became inconclusive because I did not realize that I needed to deeply wash the setup after every run (not just rinsing and wiping down). There is a thin layer of corrosion that builds up on the stainless steel that inhibits current flow, hence the vigorous washing with soap and water and occasionally brushing with a steel brush/sanding. If the fluid is not moving for you, try sanding the steel first and trying again.
Additionally, the same brine/cornsyrup mixture only produced good results for me only for 3 runs, tops. I found that the texture of the brine/cornsyrup mixture changes slightly (more microbubbles throughout) and the conductivity slightly reduces after every run and more at high current.
Overall, the higher the salinity, the more corrosion and bubbles formed. The more cornsyrup that is used, the less the tracing particles would go to the boundaries (many times the tracers would fly off to the borders and not turn with a constant radius) or move toward each other from surface tension, but because there is less brine, the harder it is to conduct. Moreover, if the particles do move with less brine, there is added time of conduction that degrades the fluid and setup. We also used photoflo to try and mitigate the surface tension as well. I didnt do enough runs to really see if it was effective, though.
I mixed the brine/cornsyrup solution with a standing rotary mixer (basically a small propeller attached to a drill) that we borrowed from another lab. I would mix the solution while I washed and dried the setup from the previous run, so I only mixed for 5 minutes; not long. If you dont have a standing mixer, a kitchen electric mixer would do the trick.
ANIMATING THE EQUATIONS:
I wrote the equations using Slideshow in PowerPoint. Under slideshow, choose record slide show. This will open a whole new screen. In the upper left corner, click record and it will record all your pen strokes. You can also pause the recording, write some more stuff, and continue recording. This creates the effect of writing instantly appearing. Each slide is basically a separate pen stroke recording. To create the video, go to file, export, then click create a video. This will create one video of all the slides strung together, one right after the other.
As a side note, I did this using a tablet pen on a tablet. I highly encourage the use of a pen because mouse writing is quite janky to say the least.
JAs Personal Notes:
NEXT STEPS:
Now, how do we make this a DIYnamics experiment (https://diynamics.github.io/) you can do in your kitchen using salt water, soup can, coffee can, plate, Vaseline, magnet(s) and a few batteries? Kinematically-Reversible Magneto-Couette Flow: The Gory Details](https://i.ytimg.com/vi/d-lc2tZsBGs/mqdefault.jpg)


