Uploaded February 2025 | Updated September 2026, 1 week ago
A project to showcase the 6 CH "Flysky" Receiver With 2 Brushed ESCs Module converting a small chuck glider.
🔧 Multi-function Board Setup: The project utilizes a multi-function board capable of controlling two brushed motors and six PWM channels. The board is a compact solution for controlling the glider's electrical systems.
🔋 Power Supply Considerations: Various power solutions are being tested, including modified battery packs with gold-plated connectors for better efficiency compared to traditional JST or pH connectors.
✂️ Wing and Control Surface Modifications: The control surfaces are cut out based on standard guide marks, with a single servo managing the ailerons and elevator.
🛠️ Servo and Control Rods: Servos from an old B-17 model are repurposed, and special adhesive tape is used for securing control surfaces.
📡 Antenna and Receiver Positioning: The antenna orientation may create signal challenges, and the optimal placement will be tested in real flight conditions.
🚀 Flight Tests and Adjustments: Initial tests reveal stability issues, requiring center of gravity (CoG) adjustments and modifications to control surfaces.
⚙️ Differential Thrust Control: The twin motors provide additional maneuverability through differential thrust, aiding directional control.
🎯 Final Adjustments and Future Improvements: Adjustments to the center of gravity, motor angles, and aerodynamics are necessary to enhance stability and flight performance.
🔗 Please tell me if any of the links provided no longer work!!
🔗 Coreless Motor Mount thingiverse.com/thing:3917756
🛒 6 CH "Flysky" Receiver With 2 Brushed ESC's banggood.com/custlink/vDvZZQGcMP?title=^ CH FlySky Rx with 2 ESC
🛒 Medical Paper Tapes Eyelash https://s.click.aliexpress.com/e/_oFGzYK6
🛒 RadioMaster Pocket banggood.com/custlink/KDK9IYPzRi?title=Radiomaster Pocket
🛒 RadioMaster Pocket Hall Gimbal Transmitter https://s.click.aliexpress.com/e/_DBpJzqt
👀 Click Here to Subscribe bit.ly/1nformatica
🛠 I buy most of my gear from https://s.click.aliexpress.com/e/_APpCVa You can help me by using these links!
👍 Follow on Facebook facebook.com/1nformatica
💲 If you would like to buy me a coffee: paypal.me/1nformatica
00:00:00,Project Overview and Multi-function Board Introduction
00:00:33,Power Supply and Battery Considerations
00:01:04,Coreless Motor Mount and Center of Gravity (CoG) Discussion
00:01:36,Control Module Placement and Servo Setup
00:02:07,Control Surface Cutting and Servo Actuation
00:02:39,Use of Adhesive Tape for Hinges
00:03:10,Elevator Installation and Antenna Orientation
00:03:41,Final Servo and Control Rod Adjustments
00:04:14,Initial Setup and Power Connection
00:04:46,Differential Thrust Testing
00:05:17,First Flight Test and Stability Observations
00:05:49,Adjusting Ailerons and Adding Nose Weight
00:06:24,Second Flight Test and Wind Conditions
00:07:07,Performance Evaluation and Future Adjustments
00:07:39,Issues with Center of Gravity and Motor Angle
00:08:12,Project Conclusion and Next Steps
DISCLAIMER: Unless otherwise stated all products shown in this video have been purchased personally. The description and video may contain links to products which might be affiliate links, so if you click on one of the product links I could receive a small commission. This does not affect the price you pay. If you do purchase through my affiliate link this will help fund future videos, thank you for your support!
#1nformatica
A project to showcase the 6 CH "Flysky" Receiver With 2 Brushed ESCs Module converting a small chuck glider.
🔧 Multi-function Board Setup: The project utilizes a multi-function board capable of controlling two brushed motors and six PWM channels. The board is a compact solution for controlling the glider's electrical systems.
🔋 Power Supply Considerations: Various power solutions are being tested, including modified battery packs with gold-plated connectors for better efficiency compared to traditional JST or pH connectors.
✂️ Wing and Control Surface Modifications: The control surfaces are cut out based on standard guide marks, with a single servo managing the ailerons and elevator.
🛠️ Servo and Control Rods: Servos from an old B-17 model are repurposed, and special adhesive tape is used for securing control surfaces.
📡 Antenna and Receiver Positioning: The antenna orientation may create signal challenges, and the optimal placement will be tested in real flight conditions.
🚀 Flight Tests and Adjustments: Initial tests reveal stability issues, requiring center of gravity (CoG) adjustments and modifications to control surfaces.
⚙️ Differential Thrust Control: The twin motors provide additional maneuverability through differential thrust, aiding directional control.
🎯 Final Adjustments and Future Improvements: Adjustments to the center of gravity, motor angles, and aerodynamics are necessary to enhance stability and flight performance.
🔗 Please tell me if any of the links provided no longer work!!
🔗 Coreless Motor Mount thingiverse.com/thing:3917756
🛒 6 CH "Flysky" Receiver With 2 Brushed ESC's banggood.com/custlink/vDvZZQGcMP?title=^ CH FlySky Rx with 2 ESC
🛒 Medical Paper Tapes Eyelash https://s.click.aliexpress.com/e/_oFGzYK6
🛒 RadioMaster Pocket banggood.com/custlink/KDK9IYPzRi?title=Radiomaster Pocket
🛒 RadioMaster Pocket Hall Gimbal Transmitter https://s.click.aliexpress.com/e/_DBpJzqt
👀 Click Here to Subscribe bit.ly/1nformatica
🛠 I buy most of my gear from https://s.click.aliexpress.com/e/_APpCVa You can help me by using these links!
👍 Follow on Facebook facebook.com/1nformatica
💲 If you would like to buy me a coffee: paypal.me/1nformatica
00:00:00,Project Overview and Multi-function Board Introduction
00:00:33,Power Supply and Battery Considerations
00:01:04,Coreless Motor Mount and Center of Gravity (CoG) Discussion
00:01:36,Control Module Placement and Servo Setup
00:02:07,Control Surface Cutting and Servo Actuation
00:02:39,Use of Adhesive Tape for Hinges
00:03:10,Elevator Installation and Antenna Orientation
00:03:41,Final Servo and Control Rod Adjustments
00:04:14,Initial Setup and Power Connection
00:04:46,Differential Thrust Testing
00:05:17,First Flight Test and Stability Observations
00:05:49,Adjusting Ailerons and Adding Nose Weight
00:06:24,Second Flight Test and Wind Conditions
00:07:07,Performance Evaluation and Future Adjustments
00:07:39,Issues with Center of Gravity and Motor Angle
00:08:12,Project Conclusion and Next Steps
DISCLAIMER: Unless otherwise stated all products shown in this video have been purchased personally. The description and video may contain links to products which might be affiliate links, so if you click on one of the product links I could receive a small commission. This does not affect the price you pay. If you do purchase through my affiliate link this will help fund future videos, thank you for your support!
#1nformatica
