Tom Stanton | DIY Electric Bike @TomStantonEngineering | Uploaded 7 years ago | Updated 7 hours ago
If you would like to build the same setup, I have listed the parts required at the bottom of this description.
Which 3D Printer do I recommend? This one: goo.gl/oM3TLg
----------------------------------------------------------------------------------------------------------------------------------------
My Other Equipment:
Main camera - http://amzn.to/2tqJKe7
Main tripod - http://amzn.to/2tqRjBt
Secondary Tripod - http://amzn.to/2t1NkMh
Microphone - http://amzn.to/2uuv9n0
Audio recorder - http://amzn.to/2v3mjcG
Banggood affiliate: banggood.com/?p=LT0710618750201406EK
Support my videos via Patreon: patreon.com/tomstanton
Huge thanks to the following Patrons for supporting me:
Bernard Gauweiler
+2 others who have chosen not to be mentioned
----------------------------------------------------------------------------------------------------------------------------------------
Other Social Media Links:
Instagram: instagram.com/stantonfpv
FaceBook: facebook.com/Tom-Stanton-171292196234142/?fref=ts
----------------------------------------------------------------------------------------------------------------------------------------
Description
Parts List
Bike: goo.gl/h2GIVm (UK)
goo.gl/MNdU2O (USA)
3D Printed parts: http://www.thingiverse.com/thing:2191603
Motor: goo.gl/3HFwXg
VESC: http://vedder.se/2015/01/vesc-open-source-esc/
Electric scooter throttle: goo.gl/yvloKG
Saddle bag: goo.gl/ilyxSJ
6s 5000mah li-po battery
HTD5 12T pulley (with 8mm bore for motor shaft)
HTD5 800x15mm belt
5pcs m4x30mm bolts (clamp motor mount to frame)
4pcs m4x10mm bolts (attach motor to mount)
1pcs m4x50mm bolt (roller bearings seat on this bolt)
5pcs m4 nyloc nuts
3pcs m3x10mm bolts (assembly of electronics case)
5mm wide cable ties (attach pulley to spokes)
EC5 battery connectors
4mm bullet connectors (for ESC)
Basic knowledge of electronics and soldering
and a 3D printer...
Also, the VESC is capable of using the electric scooter 'analog signal' and an input, so the arduino isn't required.
Get your quality 3D printer filament for an affordable price here: 3dprintz.co.uk
3D Printz on FaceBook: facebook.com/3dprintzltd
Note: The 3D printed brackets/pulley were designed specifically for the bike used in the video, it will not fit any other bike and I will not be modifying it on request to fit to other bikes.
Disclaimer: I do not hold responsibility for any wrongful riding if you chose to build this ebike. It is beyond the legal limit (250w) for an electric bike, which is why I chose to ride it within the grounds of my university.
If you would like to build the same setup, I have listed the parts required at the bottom of this description.
Which 3D Printer do I recommend? This one: goo.gl/oM3TLg
----------------------------------------------------------------------------------------------------------------------------------------
My Other Equipment:
Main camera - http://amzn.to/2tqJKe7
Main tripod - http://amzn.to/2tqRjBt
Secondary Tripod - http://amzn.to/2t1NkMh
Microphone - http://amzn.to/2uuv9n0
Audio recorder - http://amzn.to/2v3mjcG
Banggood affiliate: banggood.com/?p=LT0710618750201406EK
Support my videos via Patreon: patreon.com/tomstanton
Huge thanks to the following Patrons for supporting me:
Bernard Gauweiler
+2 others who have chosen not to be mentioned
----------------------------------------------------------------------------------------------------------------------------------------
Other Social Media Links:
Instagram: instagram.com/stantonfpv
FaceBook: facebook.com/Tom-Stanton-171292196234142/?fref=ts
----------------------------------------------------------------------------------------------------------------------------------------
Description
Parts List
Bike: goo.gl/h2GIVm (UK)
goo.gl/MNdU2O (USA)
3D Printed parts: http://www.thingiverse.com/thing:2191603
Motor: goo.gl/3HFwXg
VESC: http://vedder.se/2015/01/vesc-open-source-esc/
Electric scooter throttle: goo.gl/yvloKG
Saddle bag: goo.gl/ilyxSJ
6s 5000mah li-po battery
HTD5 12T pulley (with 8mm bore for motor shaft)
HTD5 800x15mm belt
5pcs m4x30mm bolts (clamp motor mount to frame)
4pcs m4x10mm bolts (attach motor to mount)
1pcs m4x50mm bolt (roller bearings seat on this bolt)
5pcs m4 nyloc nuts
3pcs m3x10mm bolts (assembly of electronics case)
5mm wide cable ties (attach pulley to spokes)
EC5 battery connectors
4mm bullet connectors (for ESC)
Basic knowledge of electronics and soldering
and a 3D printer...
Also, the VESC is capable of using the electric scooter 'analog signal' and an input, so the arduino isn't required.
Get your quality 3D printer filament for an affordable price here: 3dprintz.co.uk
3D Printz on FaceBook: facebook.com/3dprintzltd
Note: The 3D printed brackets/pulley were designed specifically for the bike used in the video, it will not fit any other bike and I will not be modifying it on request to fit to other bikes.
Disclaimer: I do not hold responsibility for any wrongful riding if you chose to build this ebike. It is beyond the legal limit (250w) for an electric bike, which is why I chose to ride it within the grounds of my university.
