Uploaded March 2022 | Updated September 2026, 1 week ago
In this video I walk you through the process by which you would install a BLtouch or CRtouch module onto the Creality Ender 7 printer. Currently, there is not much information available online for this modification as it seems the Ender 7 is being slowly adopted by others. I believe this printer has a lot of potential and this is a fairly easy modification to enable auto bed levelling on this printer for optimal first layer adhesion.
Overall it is a fairly easy install, the most challenging part is extending the CR touch / BL touch wiring harness as it is not long enough to reach the mainboard. There is a connector labelled BL touch on the breakout board at the top of the printer, but oddly, the connector on the Creality CR touch harness does not plug into the Creality printer… go figure.
As a bonus to the CR touch walkthrough, I will also be installing an RGB LED light strip to add some light inside of the print area and some extra colors are always fun!
To download the 3D printable file for CR touch mounting, click here:
► prusaprinters.org/prints/153172-creality-ender-7-cr-touch-bl-touch-mounting-bracke
Please remember to like and rate the file on PrusaPrints as it is a small, free, and easy gesture that helps with my ratings on that website :) I spend a of time making these videos and designing parts for the community.
In addition to the 3D printed file you will, of course, need a BL touch or CR touch module. With my bracket you will need four M3x8 socket head cap screws for mounting.
You can find the BLtouch / CRtouch firmware for the Ender 7 here:
► embracemaking.com/products/creality-ender-7-bondtech-lgx-lite-mosquito-magnum-hot-end-kit
Scroll to the bottom of the listing to find the download link.
Remember to check out Mech Solutions as they were the generous ones to provide me with this printer for development!
► mechestore.com
If you enjoyed this video please consider subscribing! Please post comments and questions below!
#DIY #3dPrinting #Creality
****************************************************************
If you enjoy and have benefited from my content and are feeling generous I would love your support! You can "buy me a coffee" here:
► paypal.com/donate/?hosted_button_id=V2T6MEFUGP73Y ☕
By supporting my channel you are encouraging me to continue with this time consuming endeavor. A lot of time goes into design work, building my projects, filming the videos, editing the videos, etc. Plus it all costs money! Your generosity goes a long way in helping me bring you better content as often as I can!
Follow me on Instagram!
► instagram.com/embracemaking 📷
If you liked this video, perhaps you will also enjoy some channels that I personally find inspiring and interesting...
► The Hacksmith
youtube.com/channel/UCjgpFI5dU-D1-kh9H1muoxQ
► Adam Savage Tested
youtube.com/channel/UCiDJtJKMICpb9B1qf7qjEOA
► Thomas Sanladerer
youtube.com/user/ThomasSanladerer
In this video I walk you through the process by which you would install a BLtouch or CRtouch module onto the Creality Ender 7 printer. Currently, there is not much information available online for this modification as it seems the Ender 7 is being slowly adopted by others. I believe this printer has a lot of potential and this is a fairly easy modification to enable auto bed levelling on this printer for optimal first layer adhesion.
Overall it is a fairly easy install, the most challenging part is extending the CR touch / BL touch wiring harness as it is not long enough to reach the mainboard. There is a connector labelled BL touch on the breakout board at the top of the printer, but oddly, the connector on the Creality CR touch harness does not plug into the Creality printer… go figure.
As a bonus to the CR touch walkthrough, I will also be installing an RGB LED light strip to add some light inside of the print area and some extra colors are always fun!
To download the 3D printable file for CR touch mounting, click here:
► prusaprinters.org/prints/153172-creality-ender-7-cr-touch-bl-touch-mounting-bracke
Please remember to like and rate the file on PrusaPrints as it is a small, free, and easy gesture that helps with my ratings on that website :) I spend a of time making these videos and designing parts for the community.
In addition to the 3D printed file you will, of course, need a BL touch or CR touch module. With my bracket you will need four M3x8 socket head cap screws for mounting.
You can find the BLtouch / CRtouch firmware for the Ender 7 here:
► embracemaking.com/products/creality-ender-7-bondtech-lgx-lite-mosquito-magnum-hot-end-kit
Scroll to the bottom of the listing to find the download link.
Remember to check out Mech Solutions as they were the generous ones to provide me with this printer for development!
► mechestore.com
If you enjoyed this video please consider subscribing! Please post comments and questions below!
#DIY #3dPrinting #Creality
****************************************************************
If you enjoy and have benefited from my content and are feeling generous I would love your support! You can "buy me a coffee" here:
► paypal.com/donate/?hosted_button_id=V2T6MEFUGP73Y ☕
By supporting my channel you are encouraging me to continue with this time consuming endeavor. A lot of time goes into design work, building my projects, filming the videos, editing the videos, etc. Plus it all costs money! Your generosity goes a long way in helping me bring you better content as often as I can!
Follow me on Instagram!
► instagram.com/embracemaking 📷
If you liked this video, perhaps you will also enjoy some channels that I personally find inspiring and interesting...
► The Hacksmith
youtube.com/channel/UCjgpFI5dU-D1-kh9H1muoxQ
► Adam Savage Tested
youtube.com/channel/UCiDJtJKMICpb9B1qf7qjEOA
► Thomas Sanladerer
youtube.com/user/ThomasSanladerer
