Uploaded November 2021 | Updated November 2026, 11 hours ago
Install and set up a Creality CR Touch on an Ender 3 or Ender 3 Pro with a Creality 4.2.2 or 4.2.7 mainboard. This walkthrough covers hardware installation, firmware, Z-offset, and the Cura change needed to run probing before prints.
Full written CR Touch installation guide, with the steps and resources in one place:
3dprintscape.com/guide-to-install-a-cr-touch-on-a-creality-32-bit-mainboard
━━━━━━━━━━━━━━━━━━━━━━
🧰 HARDWARE & SOFTWARE
━━━━━━━━━━━━━━━━━━━━━━
▸ CR Touch on Amazon: geni.us/VwD0
▸ Ender 3 Pro on Amazon: geni.us/vIAIx
▸ Ender 3 V2 on Amazon: geni.us/ur8YHM
▸ HATCHBOX filament on Amazon: geni.us/BJx0Gdj
▸ Creality firmware downloads: creality.com/download
Disclosure: Some links below may be affiliate links. If you buy through them, 3DPrintscape may earn a commission at no extra cost to you.
━━━━━━━━━━━━━━━━━━━━━━
🔗 RELATED SETUP GUIDES
━━━━━━━━━━━━━━━━━━━━━━
▸ Cura profile library: 3dprintscape.com/cura-profiles
▸ Marlin firmware builds: 3dprintscape.com/marlin-firmware-builds
▸ Firmware and upgrades hub: 3dprintscape.com/guides/octoprint-firmware-upgrades
━━━━━━━━━━━━━━━━━━━━━━
⏱️ CHAPTERS
━━━━━━━━━━━━━━━━━━━━━━
0:00 – Introduction
1:15 – What’s in the box
2:30 – Downloading & flashing the firmware
4:00 – Verifying firmware loaded correctly
4:45 – Choosing the right mounting bracket
5:45 – Attaching CR Touch to bracket
6:30 – Mounting to the printer
7:15 – Connecting the cable & cable management
8:15 – Accessing the mainboard
9:15 – Disconnecting the Z-stop
10:00 – Connecting the 5-pin adapter
10:45 – Testing before final assembly
11:30 – Running Auto Home
12:00 – Setting the Z-offset
13:30 – Adding G29 to Cura
14:30 – Summary & what’s next
━━━━━━━━━━━━━━━━━━━━━━
▶️ RELATED VIDEOS
━━━━━━━━━━━━━━━━━━━━━━
▸ Ender 3 Pro Z-axis calibration: youtu.be/lspkdhtShgc
▸ CR Touch vs. BLTouch: youtu.be/iz7I5qz2gpY
▸ CR Touch with Marlin: youtu.be/iaQSXZsybl0
▸ CR Touch on SKR Mini: youtu.be/u1c1go69zJY
▸ Marlin firmware on a Creality board: youtu.be/pQ7WZST8sqk
━━━━━━━━━━━━━━━━━━━━━━
🔔 SUBSCRIBE
━━━━━━━━━━━━━━━━━━━━━━
Practical 3D printing guides, reviews, and projects:
youtube.com/channel/UCUakh0dyF_l3b-W3x2DZplQ
━━━━━━━━━━━━━━━━━━━━━━
💬 CONNECT
━━━━━━━━━━━━━━━━━━━━━━
▸ Discord: discord.gg/Bu94EYVkrU
▸ Patreon: patreon.com/3dprintscape
▸ Website: 3dprintscape.com
━━━━━━━━━━━━━━━━━━━━━━
🏷️ TAGS
━━━━━━━━━━━━━━━━━━━━━━
#CRTouch #Ender3 #AutoBedLeveling #MarlinFirmware #Cura #3DPrinting
Install and set up a Creality CR Touch on an Ender 3 or Ender 3 Pro with a Creality 4.2.2 or 4.2.7 mainboard. This walkthrough covers hardware installation, firmware, Z-offset, and the Cura change needed to run probing before prints.
Full written CR Touch installation guide, with the steps and resources in one place:
3dprintscape.com/guide-to-install-a-cr-touch-on-a-creality-32-bit-mainboard
━━━━━━━━━━━━━━━━━━━━━━
🧰 HARDWARE & SOFTWARE
━━━━━━━━━━━━━━━━━━━━━━
▸ CR Touch on Amazon: geni.us/VwD0
▸ Ender 3 Pro on Amazon: geni.us/vIAIx
▸ Ender 3 V2 on Amazon: geni.us/ur8YHM
▸ HATCHBOX filament on Amazon: geni.us/BJx0Gdj
▸ Creality firmware downloads: creality.com/download
Disclosure: Some links below may be affiliate links. If you buy through them, 3DPrintscape may earn a commission at no extra cost to you.
━━━━━━━━━━━━━━━━━━━━━━
🔗 RELATED SETUP GUIDES
━━━━━━━━━━━━━━━━━━━━━━
▸ Cura profile library: 3dprintscape.com/cura-profiles
▸ Marlin firmware builds: 3dprintscape.com/marlin-firmware-builds
▸ Firmware and upgrades hub: 3dprintscape.com/guides/octoprint-firmware-upgrades
━━━━━━━━━━━━━━━━━━━━━━
⏱️ CHAPTERS
━━━━━━━━━━━━━━━━━━━━━━
0:00 – Introduction
1:15 – What’s in the box
2:30 – Downloading & flashing the firmware
4:00 – Verifying firmware loaded correctly
4:45 – Choosing the right mounting bracket
5:45 – Attaching CR Touch to bracket
6:30 – Mounting to the printer
7:15 – Connecting the cable & cable management
8:15 – Accessing the mainboard
9:15 – Disconnecting the Z-stop
10:00 – Connecting the 5-pin adapter
10:45 – Testing before final assembly
11:30 – Running Auto Home
12:00 – Setting the Z-offset
13:30 – Adding G29 to Cura
14:30 – Summary & what’s next
━━━━━━━━━━━━━━━━━━━━━━
▶️ RELATED VIDEOS
━━━━━━━━━━━━━━━━━━━━━━
▸ Ender 3 Pro Z-axis calibration: youtu.be/lspkdhtShgc
▸ CR Touch vs. BLTouch: youtu.be/iz7I5qz2gpY
▸ CR Touch with Marlin: youtu.be/iaQSXZsybl0
▸ CR Touch on SKR Mini: youtu.be/u1c1go69zJY
▸ Marlin firmware on a Creality board: youtu.be/pQ7WZST8sqk
━━━━━━━━━━━━━━━━━━━━━━
🔔 SUBSCRIBE
━━━━━━━━━━━━━━━━━━━━━━
Practical 3D printing guides, reviews, and projects:
youtube.com/channel/UCUakh0dyF_l3b-W3x2DZplQ
━━━━━━━━━━━━━━━━━━━━━━
💬 CONNECT
━━━━━━━━━━━━━━━━━━━━━━
▸ Discord: discord.gg/Bu94EYVkrU
▸ Patreon: patreon.com/3dprintscape
▸ Website: 3dprintscape.com
━━━━━━━━━━━━━━━━━━━━━━
🏷️ TAGS
━━━━━━━━━━━━━━━━━━━━━━
#CRTouch #Ender3 #AutoBedLeveling #MarlinFirmware #Cura #3DPrinting










